新型多效能复合式橡胶防老剂FNPPD的制备

介绍了一种新型多效复合式橡胶防老剂FNPPD及其制备。其中包括该剂主要成分668防老剂(N-苯基N′-另辛基对苯二胺)的加氢法合成;合成668的原料之一2-辛酮的制备方法,以及668与酮胺类化合物复合为FNPPD防老剂的工艺过程。生产FNPPD具有可观的经济效益和市场前景。     

超细铁粉和氧化铁颗粒的研究

用透射电镜和图像分析仪等研究了超细铁粉和γ-Fe_2O_3粉末的结构、形貌、粒子的平均尺寸以及粒度分布。研究结果表明,多数超细铁粉粒子近似呈球形,并且,铁粉粒子由两相组成,粒子的核心部分是金屑a-Fe,表面的包裹层为氧化物层,它由Fe_3O_4和7-Fe_O_3的混合物组成。氧化层的平均厚度大约占整个粒子直径的20％左右。羰基铁粉粒子(含氧化层)的平均直径为16nm。直径在4～24nm范围的粒子数占总粒子数的91％,而7-Fe_2O_3粉末既有雪茄状粒子,也有小球状粒子。分析表明,球状粒子的平均直径为113nm,雪茄状粒子的平均直径(按<长 宽>/2计算)为148nm。由于超细铁粉粒子很细,且有磁性,制备电镜试样时分散比较困难。本文比较了几种分散方法后,使用了一种较好的分散方法——超声喷管分散法。     

Flow dynamics or ‘quaking’ in gravity discharge from silos

This paper reviews the characteristics of pulsating or cyclic flow of bulk solids during gravity discharge in bins and silos. The dynamic load phenomenon is often referred to as “silo quaking” and is influenced by various factors related to the type of flow pattern developed in the bin and the flow properties of the bulk material. Of particular relevance is the influence of ‘slip-stick’ during shear flow, and the velocity at critical sections in the silo during discharge. An overview of recent and current research on this subject is presented.     

Effects of mechanical interactions on the hydrostatic stress in randomly distributed rubber particles in an amorphous polymer matrix

The equivalent inclusion method (EIM) assuming linear elasticity is used to calculate the mechanical interactions between spherical rubber particles in an amorphous matrix, as in a rubber toughened polymer. The influences of the various calculation parameters are examined and it is shown that the method can provide reliable results with regard to the level of hydrostatic stress in the particles. Damage of the material is simulated by replacing the most stressed particles by voids. Numerical simulations for several hundreds of interacting particles give information on the kinetics and spatial organisation of the damage. It appears that, as the volume fraction of particles increases from 10 to 20%, the spatial configuration of the damage evolves from a localised to a diffuse mode. These results are discussed in relation to the efficiency of rubber toughening.     

Gravity pipe flow of polymeric bulk solids in pneumatic conveying system

Various physical parameters of gravity pipes such as gravity pipe diameter, the inclination of the gravity pipe, the cone angle, temperature of the discharged material and the rate of air counter flow into the gravity pipe were studied. The results obtained from the pipe diameter and cone angle experiments showed that the mass flow rate was proportional to (D-1.4d)^2.5 and also to θ^-0.5. The results from the pipe inclination experiment showed the existence of an angle of inclination for maximum flow, which was also reported by Wieghardt [Uber einige versuche an stromungen in sand. Ingenieur Archived 20, 109-115]. The air flow experiment also showed that the mass flow rate was inversely proportional to the air counter-flow rate, and strongly influenced by the material properties. Results from the temperature experiment showed that the temperature of the material had slight effect on the mass flow rate for the temperature range that was used in the experiment. Flow visualization images showed formation of solid plugs in the pipe that played a part in influencing the behaviour and mass flow rate of solids in the system.     

纳米羟基磷灰石的合成及分散性能研究

采用中和反应制备羟基磷灰石（HA），在反应过程中添加了六偏磷酸钠、三聚磷酸钠和“快易”作分散剂。采用X射线衍射仪（XRD）、扫描电镜（SEM）、透镜电镜（TEM）、热重和差示扫描分析（TG-DSC）等测试手段对所合成的粉末进行了表征。结果表明：分散剂添加的时间对合成粉末的粒径没有明显的影响；三种分散剂中六偏磷酸钠和三聚磷酸钠的均有较好的分散效果，粉末粒径达到纳米级。     

多相物质粉末衍射的物相检索

讨论了多相物质粉末衍射的物相检索问题，介绍了XRDS的物相检索软件。这是一种智能型的物相检索程序，考虑了测试数据的不确定度，以及粉末样品和块状样品衍射图谱各自的特点，不仅注意到实际样品中微量物相存在的可能，也注意到块状样品结构有序性的可能。XRDS能够帮助材料工作者同时检出样品中所含的多种物相及其含量，操作简单、结果可靠。     

一起氧气瓶燃割事故分析

20 0 2年 5月 30日晚 7:5 5 ,徐州市工程集团某机械厂下料车间 ,氧气汇流排中一只即将开启使用的氧气瓶发生燃烧击穿事故 ,造成一死一伤的严重后果。事故发生的第二天笔者被特邀赶到现场 ,会同调查组对事故的性质、原因进行分析鉴定 ,并通过了原因分析鉴定结论。为防止此类事故的再次发生 ,引起充装或使用单位的足够重视 ,从中吸取教训 ,把事故消灭在萌芽状态 ,减少不必要的损失 ,现将这起氧气瓶燃割事故介绍如下。1　钢瓶及汇流排的原始情况钢瓶为河北涿鹿高压气瓶制造厂生产 ,气瓶原始数据如下 :气瓶编号 0 85 15 ,水压试验TP2 2 5 ,工…     

喷雾沉积快速凝固技术的发展与展望

喷雾沉积是制取大体积快凝材料的一种新工艺。本文综述了它的产生和发展，概述了其基本原理和过程控制。对该领域今后的发展动向，提出了一些新看法。     

聚合物分解法制备微波介质陶瓷粉体的研究

对采用聚合物分解（Ｐｅｃｈｉｎｉ）法制备ＭｇＴｉＯ＿３粉体进行了研究。通过对聚合中间产物进行红外光谱分析，研究了聚合物分解法制备ＭｇＴｉＯ＿３陶瓷粉体的聚合反应过程及产物。并与用传统固相反应法制备粉体工艺进行对比．从而证明用聚合物分解法可获得单一ＭｇＴｉＯ＿３相材料．并可降低粉体的煅烧温度。