Uncertainty of Predictions of Embankment Dam Breach Parameters

Risk assessment studies considering the failure of embankment dams often require the prediction of basic geometric and temporal parameters of a breach, or the estimation of peak breach outflows. Many of the relations most commonly used to make these predictions were developed from statistical analyses of data collected from historic dam failures. The prediction uncertainties of these methods are widely recognized to be very large, but have never been specifically quantified. This paper presents an analysis of the uncertainty of many of these breach parameter and peak flow prediction methods. Application of the methods and the uncertainty analysis are illustrated through a case study of a risk assessment recently performed by the Bureau of Reclamation for a large embankment dam in North Dakota.     

L-CKM 220开式齿轮油的研制

通过对基础油，增粘剂、降凝剂和其它添加剂的筛选，确定了L-CKM220开式齿轮油的配方，参照AGMA 251．02 EP极压开式齿轮油规范，制定了L-CKM220开式齿轮油的暂定质量标准，产品经应用试验表明：能满足开式齿轮的润滑要求。     

Structural integrity in electronics

With continuing miniaturisation, increased performance demands and the requirement to remove lead from solder alloys, the challenges to structural integrity and reliability of electronic equipment are substantial and increasing. This paper outlines typical features in electronic equipment of which the structural integrity community may be generally unaware. Potential failure modes in service are described, and the problems of scale and material characteristics are considered. Progress in the application of fracture mechanics to the life prediction of interconnections is reviewed. The limited evidence available suggests that the crack growth resistance of silver‐containing lead‐free solders is superior to that of the traditional Sn‐37Pb under cycle‐controlled conditions but there is no difference when time‐dependent conditions prevail. In several respects, it is contended that the electronics sector is faced with challenges at least equivalent to those encountered in gas turbines and nuclear power generation.     

Tensile fracture and failure behavior of technical flax fibers

The apparent tensile strength of technical flax fibers was determined in single‐fiber tests at various clamping lengths (20, 40, and 80 mm) and the outcome was compared with literature data. It was demonstrated that the strength of flax at each clamping length obeyed the two‐parameter Weibull model. The failure mode and sequence were studied in situ (i.e., during loading) by SEM and acoustic emission (AE). The failure sequence (axial splitting of the technical fiber along its elementary constituents, radial cracking of the elementary fibers, multiple fracture of the elementary fibers) concluded reflected the hierarchical build‐up of the flax bast fibers. To the above failure events AE amplitude ranges were assigned. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3638–3645, 2003     

VOD在有线电视网的实现

从视频点播系统的结构及组成和在有线电视网络中VOD系统的结构模式与应用两个方面，详细地阐述了如何利用有线电视网络实现视频点播，主要从以下3个方面介绍关于视频点播系统VOD技术：①视频点播VOD的技术原理；②视频点播系统的结构及组成；③有线电视视频点播系统的结构模式与应用。     

非均匀材料破坏过程数值模拟的边界元法研究

用格子模型和统计分布模拟非均匀材料性质的初始分布,针对二维非均匀材料格子模型建立了重复多子域边界元法求解方程。通过把各行子域集成为亚子域,然后对链状排列的亚子域应用域转移矩阵法进行求解。由于使用的域转移矩阵法对内存的要求仅略大于一个亚子域的求解,以及重复多子域法只需要进行一次系数矩阵积分,因而可以大大提高求解的规模和效率。在此基础上,对非均匀脆性材料在简单载荷作用下的破坏过程进行了数值模拟。采用重复多子域法和域转移矩阵法,可以得到子域内高精度的连续应力分布,为进一步研究非均匀材料裂纹萌生、扩展和破坏过程提供了基础。     

Stress Heterogeneity Effect on the Strength of Silicon Nitride

The experiments reported in this paper demonstrate the causes of the failure of monolithic ceramics. The specimens are made of silicon nitride and tested at room temperature. The stress field within the specimen is different for each of four series of tests that have been conducted. Fractographic observations have also been made to identify the causes of the failures. A size effect analysis is performed.     

岩金矿山采空区处理现状及对策

岩金矿山以浅眼留矿法为代表的空场采矿法为主要开采手段，约占50％，每年形成数百万m^3采空区，并绝大多数未进行专门处理。本文介绍数例岩金矿山采空区处理方法及效果与对策，供有关企业参考。     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Evaluation of Slow Crack Growth Resistance in Ceramics for High-Temperature Applications

The slow (subcritical) crack growth (SCG) resistance of Si₃N₄ and SiC ceramics has been evaluated by a stepwise loading test on bending bars precracked by Vickers indentation. Three highly refractory materials were selected for the evaluation: i.e., (1) high-purity Si₃N₄ sintered by hot isostatic pressing (HIP) without additives and (2,3) α - and β - SiC pressureless sintered with B and C addition. Under the hypothesis of linear elastic behavior at high temperature, which was found satisfied in the present materials, the SCG resistance was expressed in terms of initial stress intensity factor critical for SCG failure within a predetermined lifetime. The present method was found useful in shortening the testing time and consistent with other traditional fatigue tests (e.g., static-fatigue test): It is recommended as a screening test for materials under research and development. Among the materials tested in the present study, the highest SCG resistance up to 1440°C was found in the high-purity Si₃N₄ without additives.