炭黑填充硬聚氯乙烯的改性

为使聚氯乙烯具有抗静电性能,采用加入具有导电性填料的方法,但加入大量的填料,会使硬聚氯乙烯的冲击性能降低,加工性能变差。本文是在以炭黑为填料的基础上,研究不同的改性剂和加工助剂改进硬聚氯乙烯的效果,结果表明,加入冲击改性剂和加工助剂后,大大增加了硬聚氯乙烯的冲击强度,且加工性能也得到改善,同时由于炭黑具有补强效果,其拉伸强度和弯曲强度在加入改性剂后也能满足使用要求。     

聚氯乙烯(PVC)共混合金──(Ⅰ)聚氯乙烯(PVC)基础知识

本讲主要介绍聚氯乙烯（PVC）的基础知识，如PVC发展史、生产情况、型号、性能、用途及改性的必要性等，使读者对PVC的基本情况有一个大概的了解。     

污水处理中物化与兼性生化低温下的协同作用

针对兼性生化低温状态去除效果差、污泥易流失等问题,提出采取物化兼性生化联用法来提高其处理效果.并采用对比法研究物化、兼性生化及二者联用技术处理低温城市污水.研究结果表明在聚合氯化铝（PAC）投加量为20mg/L时,物化与兼性生化在COD、浊度及TP的去除方面表现出良好的协同作用,但脱氮效果一般;二者协同作用能以较小的投药量有效改善低温状态兼性生化处理效果及污泥流失现象,为后续生态单元的稳定运行提供了保障.     

Electrodialytic extraction of Cu,Pb and Cl from municipal solid waste incineration fly ash suspended in water

The possibility of using fly ash from municipal solid waste incineration (MSWI) in, for example, concrete is considered. MSWI fly ash, however, has too high a concentration of heavy metals, which may cause leaching problems during use or problems with waste handling at the end of the lifetime of the concrete. The Cl content in MSWI fly ash is also too high and will cause corrosion problems in reinforced concrete. The possibility of removing some of the unwanted heavy metals (Cu and Pb) together with Cl from an MSWI fly ash suspended in water using an electrodialytic separation method was investigated. The removal of Pb and Cu was found to be highly pH dependent and the highest contents removed were 41 and 90%, respectively. The Cu concentration of the ash decreased from 2200 to 860 mg kg^?1 but the Pb concentration increased from 8560 to 16 800 mg kg^?1, showing that Pb is mainly found in the ash fraction that is least soluble. Hence electrodialytic treatment of the ash suspended in water is not a solution to improve the ash quality in terms of Pb. The water‐soluble Cl content per unit weight of the original ash was 12.4%. The removal of water‐soluble Cl was efficient and >98% of Cl was removed (calculated on the basis of mean initial and final concentrations). This result indicates that electrodialytic extraction may be a method that can be used for the removal of Cl from ash prior to its utilization in concrete. Copyright © 2006 Society of Chemical Industry     

Rheological and mechanical properties of PVC/CaCO3 nanocomposites prepared by in situ polymerization

Poly(vinyl chloride) (PVC)/calcium carbonate (CaCO₃) nanocomposites were synthesized by in situ polymerization of vinyl chloride (VC) in the presence of CaCO₃ nanoparticles. Their thermal, rheological and mechanical properties were evaluated by dynamic mechanical analysis (DMA), thermogravimetry analysis (TGA), capillary rheometry, tensile and impact fracture tests. The results showed that CaCO₃ nanoparticles were uniformly distributed in the PVC matrix during in situ polymerization of VC with 5.0 wt% or less nanoparticles. The glass transition and thermal decomposition temperatures of PVC phase in PVC/CaCO₃ nanocomposites are shifted toward higher temperatures by the restriction of CaCO₃ nanoparticles on the segmental and long-range chain mobility of the PVC phase. The nanocomposites showed shear thinning and power law behaviors. The ‘ball bearing’ effect of the spherical nanoparticles decreased the apparent viscosity of the PVC/CaCO₃ nanocomposite melts, and the viscosity sensitivity on shear rate of the PVC/CaCO₃ nanocomposite is higher than that of pristine PVC. Moreover, CaCO₃ nanoparticles stiffen and toughen PVC simultaneously, and optimal properties were achieved at 5 wt% of CaCO₃ nanoparticles in Young's modulus, tensile yield strength, elongation at break and Charpy notched impact energy. Detailed examinations of micro-failure micromechanisms of impact and tensile specimens showed that the CaCO₃ nanoparticles acted as stress raisers leading to debonding/voiding and deformation of the matrix material around the nanoparticles. These mechanisms also lead to impact toughening of the nanocomposites.     

3-十二烷氧基-2-羟丙基三甲基氯化铵水溶液与烷烃的动态界面张力

用旋转滴法测定了3-十二烷氧基-2-羟丙基三甲基氯化铵（R12TAC）水溶液与系列烷烃的动态界面张力（DIFT），考察了浓度、温度和烷烃链长对DIFT的影响，并详细表征了DIFT随时间的变化过程。根据修正的Word-Tordai方程计算了DIFT的有关参数。结果表明：R12TAC浓度越大，DIFT曲线越低，DIFT下降越快，达平衡值的时间越短；随R12TAC浓度的增大，表观扩散系数Da从2．02×10^-10m^-2·s^-1减小到0．14×10^10m^-2·s^-1，吸附势垒Ea从2．60kJ·mol^-1增大到9．32kJ·mol^-1；温度升高，DIFT降低，表观扩散系数Da升高，而吸附势垒降低；固定一种表面活性剂溶液，测定R12TAC／系列烷烃溶液的动态界面张力，发现R12TAC／正己烷体系的DIFT最低，这与表面活性剂在水和油中的溶船度有关。     

氯化锂－水吸附式再循环型空调制冷系统性能研究

对氯化锂－水吸附式空调系统在再循环运行方式下的性能进行了模拟。分析了再生温度、热交换器效率及蒸发冷却器效率对性能的影响。与开式通风型空调制冷系统的制冷性能相比，再循环型空调制冷系统的制冷能力较大，但性能系数ＣＯＰ较小     

浅谈有堰汽提塔在PVC生产中的应用

介绍了聚合后处理工序—有堰汽提塔的装置特点、工艺以及在生产中的应用。运行应用体现了该装置高效、低耗、环保、优等品率高等特点。     

新型氯乙烯非均相聚合动力学和成粒机理

对以正丁烷（But)为反应介质的新型氯乙烯（VC）非均相聚合动力学和成粒机理进行了研究，根据VC-But二元体系气液平衡方程，由聚合过程气相压力或组成变化计算VC聚合转化率，VC非均相聚合的诱导期不明显，自动加速现象一般发生在聚合前、中期，后期聚合速率较小，新型VC非均相聚合PVC树脂的体粒径与悬浮PVC树脂相当，数均粒径较小，PVC颗粒由基本不熔结的初级粒子组成，颗粒内部初级粒子分布密度大，粒径大，孔隙率高；而在颗粒表层初级粒子分布密度高，粒径小，孔隙率低；树脂的增塑剂吸收率远大于悬浮PVC树脂，根据PVC树脂的颗粒特性和PVC与VC／But混合液的溶解度参数差异，推断聚合成粒机理为：PVC分子链在很低转化率时就从聚合介质中沉析出来并聚集形成微区，初级粒子和颗粒；后期成粒过程包括颗粒内部初级粒子的增长和向表层的离心聚集，颗粒对新形成的大分子链及其初级聚集体的捕捉等。