NiTi形状记忆合金基本驱动特性

研究了预应变ＮｉＴｉ形状记忆合金的基本驱动特性，结果表明，加热和冷却过程回复力存在滞后行为；卸载过程中应力与应变具有与加热、冷却过程相关的非线性关系；卸尖力随卸载应变速率增加而降低，此外研究了预应变ＮｉＴｉ合金丝产生回复力后对外应力的响应行为。     

桐油改性酚醛树脂的结构及固化过程的研究

通过桐油与苯酚在酸性催化剂存在下反应，然后再在碱性催化剂存在与甲醛反应制得了一种热固性桐油改性酚醛树脂。利用红外光谱，差示扫描量热法分析技术对改性树脂的结构及固化反应过程进行了研究。     

C50 级混凝土冬季施工技术探讨

介绍了应用在预应力砼Ｔ型梁的Ｃ５０级砼的冬季施工配制措施，并给出了－１０℃条件下的砼有效配合比及冬季４５℃±５℃蒸汽养生法措施。     

优化SMC模压工艺控制制品收缩率和表面粗糙度

优化SMC模压工艺参数：模压压力分为二阶段，选定最佳压力释放时机和压力；适宜降低模压温度。可显著降低SMC制品的固化收缩率，提高其表观质量、试验表明，同时采用的线收缩率和表面粗糙度两种检测和村定方法具有很好的同一性。     

双马来酰亚胺树脂体系的固化反应研究

利用ＤＳＣ及原位ＦＴＩＲ技术研究了双马来酰亚妥树脂体系的固化反应，获得了在固化反应过程中各组分的转化率与时间的关系，结合热分析数据，确立了最佳固化工艺。     

The combined effects of curing and environmental exposure on fracture properties of woven carbon/epoxy laminates

This paper concerns a study of the combined effects of curing conditions and environmental exposure on the ultimate properties of two commercial woven carbon/epoxy laminates. Curing parameters (heating rate and applied pressure) were varied so as to obtain six different conditions for each material. Moisture saturation was also achieved by exposing some of the cured samples to environmental conditions of 70°C and 95% relative humidity. Four different tests (tensile, impact, Mode I and Mode II interlaminar fracture resistance) were therefore performed, and the results obtained on the different materials before and after moisture saturation compared. Neither curing pressure nor heating rate nor moisture absorption were observed to have any practical effect on tensile and impact properties. On the contrary, one noticeable effect was the interlaminar fracture resistance of the laminates. The results are discussed and interpreted in terms of damage formation and stress intensification mechanisms.     

导电相和固化剂对铜系导电涂料性能的影响

利用IR、SEM等手段,较详细地研究了铜粉–环氧树脂体系中固化剂与铜粉的相互作用,并探讨了铜粉用量、形状对涂料导电性能的影响规律。结果表明:固化剂(最佳用量为20%左右)可以通过形成配合物的反应,有效除去铜粉表面的氧化物,极大改善涂料导电性,使填充75%铜粉的体系具有约0.2×104Ω·m的体积电阻率。应用渗流模型和导电通道理论分析铜粉的用量、形状对涂料导电性能的影响规律。     

气体悬浮焙烧炉内衬烘炉曲线的确定

根据所使用的低水泥浇注料的性能，对中铝山西分公司检修厂4号焙烧炉制定了合理的烘烤曲线，提高了耐火内衬的质量，延长了内衬的使用寿命。     

Effects of processing conditions on the curing of a vinyl ester resin

The effects of temperature, initiator, and accelerator levels on the curing of an epoxy bisphenol‐A vinyl ester resin Derakane® 411‐45 (formulated with styrene) were investigated by gel‐time and exotherm‐peak measurements on bulk samples. It was observed that the gel time was reduced as the initiator or accelerator ratio increased. Except at higher contents of the accelerator, a small kinetic plateau was seen in the gel curve and a shift of the maximum exotherm toward high temperatures in the DSC curves. This was explained by the dual role played by the accelerator species. A regression analysis of all gel‐time data showed a dependence of 3/2 order in the accelerator and first order in the initiator concentrations. Thus, for this polymerization initiation system, the gel time can be predicted for any initiator and cobalt levels and at any temperature within the ranges studied. The effect of the initiator on the unreacted styrene and vinyl ester was also examined. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1146–1154, 2002; DOI 10.1002/app.10403     

环境湿度对贮存树脂的影响EI

通过对中温固化环氧树脂ＤＳＣ、扭辫分析、凝胶时间、粘度、力学性能的测定，固化反应活化能的计算，研究了在贮存树脂的过程中环境湿度对树脂的固化反应和性能的影响。