关于粉体成球机盘体几何形状的研究

通过对粉体小球在粉体成球机盘底上运动轨线的研究,利用Euler定理,结合其参数特点,得到了不同几何形状的盘底在成球过程中对粉体小球运动的影响,球面盘底较平面盘底更有利于成球的结论。     

纳米Fe粉的制备研究

总结了纳米Fe粉的制备方法,重点介绍了一种新的制备方法——封闭循环氢还原法。该方法以FeSO·47H2O和NaOH为原料,采用沉淀方法制备粒径为30～70nm的Fe2O3粉末,其反应条件为:反应温度50℃,反应终点pH值大于12,陈化时间1h。用封闭循环氢还原法,在400℃下还原Fe2O3得到了Fe粉。其粒径在20～50nm之间,含量为99.16%。     

激光二极管线阵光束变换研究

推导出激光二极管线阵光束通过透镜系统的光强分布表达式，分析了出射光束的传输特性，设计一种凹柱透镜的光束变换系统得到一维均匀光强分布。此外，给出扩展角宽度的计算公式。     

结构-波浪-海床耦合系统中大圆筒结构的波压力响应

以沉入式大圆筒结构为对象，通过设计随机波浪水槽实验，测取了在单筒和连续筒两种结构型式、两种沉入深度和两种波谱输入下结构表面的动波压力分布。波面高度以及波压力历程均在领域进行分析。通过计算结构表面沿高程和沿环向的波压力谱及波压力传递函数，将单筒实测结果与基于线性绕射理论的解析解进行了比较，同时也详细对比了两种结构型式下的实测结果。文中汇报了在研究中获得的新发现及进行的相应分析，特别是在结构——波浪——海床动力相互作用下对波压力响应机理以及针对连续筒的研究，可为工程应用提供有价值的参考。     

Research and application of automatic control system of argon blowing at ladle shroud

Argon blowing at the ladle shroud requires the best flow control strategy to effectively avoid the secondary oxidation of molten steel, slag entrapment and heat loss during the casting of the tundish, and at the same time, give full play to the role of bubbles to remove inclusions. Therefore, an automatic control system for argon blowing at the ladle shroud was proposed. The data collected by S7-300PLC and software programming were used to adjust the argon blowing flow online in real time according to factors such as pouring and continuous pouring. On this basis, PID control algorithm and closed loop control mechanism were used for real time adjustment. The flow control valve ensures theminimum deviation between the actual value of the flow and the set value. The production data of this system in the first quarter of 2021 in a special steel plant show that the proportion of furnaces with an acid soluble aluminum (Als) loss percentage of less than 10% of each steel grade has increased by 5.52%, and the proportion of furnaces with an Als loss percentage of more than 60% has increased from 1% decrease to 0. The actual application results show that the use of the system improves the surface quality of the continuous casting slab and the performance of the final product.     

空调器用风冷冷凝器换热能力实验研究

实验测定了几种不同铜管、肋片组合的冷凝器在不同的风量和风机转速下的换热量，发现采用内螺纹铜管和迎风侧平片、背风侧冲缝片的冷凝器具有最优的换热性能。分析了多流路冷凝器中不同流路之间的制冷剂分配不均匀性和再热现象。     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

螺旋翅片管的换热计算

本文引入区域平均表面传热系数的概念。在实验研究的基础上进行了肋基和肋端温度分布预测及肋片换热数值计算。     

涠12-1构造成藏条件分析

在湘西南凹陷东区B洼陷发现的涠12-1断鼻构造油气藏,是一个中型高丰度、高产、轻质油藏.该油藏的形成是由于涠二段有较厚的湖相泥岩既作盖层,又作断鼻侧的侧封层;涠三段有三角洲砂体,砂岩发育,单层厚度大,物性好,与上覆涠二段泥岩配置成极佳的储盖组合.其油气是通过断层从流沙港组运移到涠洲组各自的圈闭中.这个富集、高产油气藏的发现,加深了对凹陷东区涠洲组石油地质条件和成藏模式的认识.     

安居水电厂灯泡贯流式水轮发电机组的试运行

本文对安居水电厂2台灯泡贯流式水轮发电机组自投入试运行以来,出现的受油器壳体开裂、导叶接力器缸体和活塞拉伤、转轮桨叶传动拐臂连接销脱落、导叶外轴承座漏水、主轴工作密封漏水侵入水导轴承、锁锭装置固定螺钉剪断等故障的经过、原因分析及其处理办法进行了叙述。