Maximum capacity of distributed generators connected to a distribution system with a step voltage regulator,as determined with an electric power density model

In a distribution system containing a step voltage regulator (SVR), the maximum capacity of distributed generators (DGs) is calculated for DGs completely dispersed on a distribution line. The maximum capacity of the DGs is calculated under the constraint of an upper or lower voltage regulation value and an allowable current value by using voltage and current profiles expressed analytically in terms of our proposed power density model. As the voltage control method for the SVRs, we consider the conventional SVR, whose transformation ratio is fixed to 1 if it detects reverse power flow, and a reverse power flow SVR which operates appropriately even if it detects reverse power flow. Calculation of the maximum capacity of DGs with respect to the power factor of the DGs indicates which parameters, including the power factor of the DGs, the distribution of the DGs, and the load, influence the maximum DG capacity. Calculation of the maximum capacity of DGs versus the system length indicates that the constraints can be subdivided into two modes in the conventional SVR and four modes in the reverse power flow SVR. The maximum DG capacity in the system with a reverse power flow SVR is larger than that in a system with the conventional SVR. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 165(4): 41–51, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20591     

The dispersion mechanism of TiB2 ceramic phase in molten aluminium and its alloys

Titanium diboride (TiB₂) ceramic particulates are dispersed in molten aluminium and its alloys for grain refining and for making cast metal–matrix composites. For producing cast MMC, the dispersion of the ceramic phase via in-situ aluminothermic reduction of K₂TiF₆ and KBF₄ flux mixture with molten aluminium and, via the addition of exogenously formed TiB₂ with the fluoride flux has been studied at 900°C. In this article, the aspects of interfacial energy that govern the dispersion and agglomeration of TiB₂ particulates are examined. The Gibbs-adsorption interface equation is particularly employed to define and to quantify the change in the surface energy as a function of the alloying element concentration and, consequently the effect of interfacial energy on the nucleation rate of TiB₂ formed via metallothermic reduction reaction and the size of the ceramic phase is also explained.     

Complex aerohydrodynamic research and the effectiveness of arresting dispersed particles for barbotage‐rotation

The design of barbotage‐rotation installation with different profiles of blades of the rotator has been created on the basis of modeling method. As a result of the complex of aerohydrodynamic research in the system “gas–liquid” carried out on the barbotage‐rotation unit, certain recommendations on the improvement of the construction and operating conditions have been developed with a view to a rise in the effectiveness of dust removal. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Electrochromic Polymer‐Dispersed Liquid‐Crystal Film: A New Bifunctional Device

Polymer‐dispersed liquid crystals (PDLCs) are liquid‐crystal dispersions within a polymer matrix. These films can be changed from an opaque to a transparent state by applying a suitable alternating‐current electric field. PDLCs have attracted the interest of researchers for their applications as light shutters, smart windows, and active displays. For such applications, electrochromic devices, which change color as a result of electrochemical reactions, have also become a recent focus of research. Herein, we report our preliminary results on bifunctional devices based on PDLCs that host electrochromic guest molecules. Such devices allow both an independent and fast switching from a scattering opaque state to a transmissive transparent state owing to liquid‐crystal reorientation and a color change from white (pale yellow) to dark blue, due to either oxidation or reduction of the electrochromic molecules.     

Condensation enhancement on a vertical plate (1st report,heat transfer characteristic on a dispersed finned surface)

In this study, a condensation heat transfer experiment on vertical continuous and dispersed finned surfaces using FC5312 was carried out. Experimental parameters were the pitch and height of the fin, and the dispersed fin length. In the results, the phenomena of condensate retention were observed in the bottom of each row of the dispersed fin. The condensate flow from the upper row was concentrated into the valley of the fin and then flowed down into the valley of the next fin. Moreover, it was found from the experiment that the heat transfer coefficient on the dispersed finned surface was lower than the one on the continuous finned surface as the fin pitch was smaller, but was larger than that of the continued finned surface for a larger fin pitch. Furthermore, the heat transfer enhancing effect became more significant for the higher fin with the larger fin pitch, and the heat transfer reducing effect became more significant for the lower fin with the smaller fin pitch. These special characteristics of condensation mentioned above were caused by the phenomena of condensate retention in each row of the fin and the flow pattern of the condensate between two adjacent fins on the dispersed finned surface based on experimental observations. © 2008 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20221     

Holographic polymer dispersed liquid crystals (HPDLCs) containing triallyl isocyanurate monomer

The morphology and corresponding performance of holographic polymer dispersed liquid crystals (HPDLCs) based on thiol-ene polymer are dependent on a number of factors including the gel point conversion of the polymer, polymerization kinetics, and extent of liquid crystal (LC) phase separation. Previous research of HPDLC reflection gratings made from thiol-allyl ether polymer indicates that increasing polymerization rate in systems with moderate gel point conversion can improve diffraction efficiency (DE). This work examines HPDLC reflection gratings that contain the ene monomer triallyl isocyanurate (TATATO). In HPDLCs, thiol-TATATO polymerization is two times faster than the thiol-ene polymerization of triallyl ether. By substituting TATATO for triallyl ether, the LC droplet size within HPDLC reflection gratings decreases from 100 nm to 25 nm. The dramatic reduction in LC droplet size for thiol-TATATO HPDLCs increases baseline transmission from 55% in thiol-triallyl ether HPDLCs to 90% at 450 nm. Unfortunately, the DE of thiol-TATATO HPDLCs is only approximately 10% due to poorly defined lamellae in the grating morphology. As determined with real-time IR (RTIR) spectroscopy, thiol-TATATO HPDLCs have significantly faster LC demixing kinetics in comparison to thiol-allyl ether HPDLCs. During holographic photopolymerization, the increased rate of LC demixing causes formation of LC droplets throughout the grating. The low DE of thiol-TATATO HPDLCs can be improved by mixing TATATO and allyl ether monomer. The morphology of ternary thiol-ene HPDLC formulations containing TATATO and allyl ether has a well-defined grating structure due to increased LC solubility in the system, an average LC droplet size of 50 nm, and baseline transmission of nearly 85% at 450 nm.     

Preparation of Highly Dispersed and Ultrafine Pt Particles on Carbon Nanotubes used as an Effective Electrochemical Catalyst

研究了不同分散程度的双壁碳纳米管(DWCNTs)作为载体沉积Pt,得到了尺寸2.08 nm的Pt颗粒均匀分散于DWCNTs表面。这种尺寸与分散状态的Pt颗粒相比其样品显示了极高的电催化活性(电流密度为0.022 A·cm?2,电化学比表面积为86.38 m2 ·g-1)。进一步的分析表明,载体在溶液中的浓度对形成Pt颗粒的尺寸和分布具有重要影响,这种尺寸与分散状态的Pt颗粒可以实现高电催化活性和低成本的Pt催化剂制备     

半组合结构压弯构件滞回试验的有限元模拟

基于按结构材料力学功能建立离散化单元的思想,将混凝土离散为各向的弹塑性弹簧单元,建立了半组合结构柱的有限元模型。通过有限元软件ANSYS对6个半组合结构压弯构件进行了反复荷载作用下的滞回性能非线性分析,得到了其荷载一位移曲线,并与试验结果进行了对比。结果表明：由有限元模型得到的滞回曲线与试验曲线相似,模拟效果良好;该有限元模型能模拟构件的弹塑性行为和抗震性能,建模简单,结果可信,计算效率高,可用于构件滞回性能的参数分析。     

流场下不相容聚合物共混物分散相形态的研究进展

介绍了流场下不相容聚合物共混物分散相形态及演变研究进展,并指出这是获得性能优异共混材料的关键。在流场下,不相容共混物分散相尺寸由破碎和凝聚等动力学过程决定。鉴于模型的理想化,早期研究主要针对牛顿流体,且分散相的变形、破碎和凝聚等理论均发源于此。对于聚合物共混物,其在本质上与牛顿流体有很多相似之处,然而,独特黏弹性质却是影响其相形态的重要因素。最后,对一些预测分散相尺寸的理论模型进行了总结,并重点讨论了分散相浓度、聚合物弹性、增容和填料等因素对流场下分散相形态的影响。     

激光光学系统测试设备的关键技术研究

说明了激光光学系统测试设备的系统组成、功能、原理、指标,着重讲述了使用的关键技术。该设备可以测试激光光学系统的弥散斑、视场等指标。