开关稳压电源用铝电解电容器的失效机理

概述了开关稳压电源用铝电解电容器的工作状态和失效模式，着重讨论了开关稳压电源用铝电解电容器的开路失效和击穿失效机理。     

X60管线钢疲劳特性的研究

利用2、4和14mm的X60钢紧凑拉伸试样进行同样应力水平、固定应力比（R＝0．1）的疲劳裂纹扩展试验，揭示出高韧性管道钢的疲劳裂纹扩展存在显著的厚度效应。由于应力水平低，相应的离面应力也低，不足以导致分层开裂，因此，裂纹端部的三维应力约束随厚度增加而增大。4mm试样的疲劳裂纹速率远高于2mm试样，但厚度再增大，裂纹扩展速率不再有显著变化。进一步对表面裂纹试样进行疲劳裂纹扩展试验，并用勾线法纪录裂纹扩展情况，利用穿透裂纹的da/dN-ΔK曲线预测表面裂纹扩展，用2mm厚试样的数据控制裂纹表面长度的扩展，用14mm厚试样的数据控制裂纹底部沿厚度方面的扩展，得到了与表面裂纹扩展实验吻合很好的预测结果。     

Engineering Geological Problems of Levee Along Middle and Lower Reaches of Yangtze River

1　ＩｎｔｒｏｄｕｃｔｉｏｎＢｅｃａｕｓｅｏｆｔｈｅｃｏｍｐｌｉｃａｔｅｄｓｕｂｓｏｉｌｐｒｏｆｉｌｅ ,ｔｈｅｌｅｖｅｅａｌｏｎｇｍｉｄｄｌｅａｎｄｌｏｗｅｒｒｅａｃｈｅｓｏｆＹａｎｇｔｚｅ ,ａｂｏｕｔ 36 0 0ｋｍｌｏｎｇ ,ｈａｓｍａｎｙｈｉｄｄｅｎｐｅｒｉｌｓ .Ａｍｏｎｇｔｈｅｄａｎｇｅｒｏｕｓｅｖｅｎｔｓｄｕｒｉｎｇ 1998’ｓｆｌｏｏｄｓｅａｓｏｎｉｎｔｈｅｗｈｏｌｅｖａｌｌｅｙ ,12 .7%ｏｃ ｃｕｒｒｅｄａｌｏｎｇｔｈｅｔｒｕｎｋｓｔｒｅａｍｄｙｋｅｓ,ｏｆｗｈｉｃｈ 6 98ｗｅｒｅｔｈｅｍｏｓｔｄ…     

The effect of a solid additive on rolling fatigue life

Behaviour of a series of lubricant oils and the effect of a non stoichiometric inorganic compound, as solid extreme pressure additive, on rolling fatigue life are studied using the rolling four-ball accelerated service simulation test proposed by Barwell and Scott. The results show, in all tested cases, the remarkable efficacy of this type of additive. The Total Acidity Number (tan) was found to increase with performance time for the case of the base lubricant, while for the oils with additives, it remained at its constant low value. This led to a proposal of a possible mechanism of the additive performance in the rolling process.     

Microscopic and Macroscopic Growth Rates of Fatigue Cracks in Steels and Alloys under the Influence of Crack Closure

On the basis of the experimental data, we show that the difference between the macroscopic and microscopic fatigue crack growth rates in the second section of the kinetic diagram of fatigue fracture is caused by the effect of crack closure within the limits of its existence. We establish the relationships between the macroscopic and microscopic fatigue crack growth rates and the structure of the material in the second section of the diagram for various values of the load ratio with regard for the effect of crack closure and propose a procedure of examination of the fracture processes in structural materials based on the analysis of microscopic and macroscopic fatigue crack growth rates.     

Effects of solidification structure on fatigue crack initiation and fatigue strength in Al−Si−Mg cast alloys

Rotating-bending uniaxial fatigue tests and micro-fatigue crack initiation tests were carried out using a permanent mold cast (PMC) and semi-solid die cast (SDC) with Al−7%Si−0.35%Mg composition in order to examine the relationship between solidification structures and fatigue behaviors. The crack length was measured using a replication method. Fatigue strength was improved in SDC, which was almost consistent with the predicted fatigue strength using the size of Si particle cluster. Resistance to fatigue crack initiation and fatigue strength were improved in SDC owing to the finer Si cluster and to higher ultimate tensile strength. Fatigue crack in PMC was preferentially initiated at pores. For SDC, the fatigue crack was initiated at the Si particle/matrix interface, and then sucessively grew along eutectic cell boundaries.     

Failure analysis used for remanufacturing of steel rolling components

The guide-pieces, used in the process line of steel rolling, were the important components. The guidepieces, which were slide contacting with the rolled-piece, had a high temperature and high speed. The wear was very serious. The results from failure analysis showed that there were three failure forms in the guide-pieces: the first was the wear during heat friction, the second was the heat fatigue under the cycle of deep heating and deep cooling, and the third was the impact rupture. Among them, the wear was the main reason. To the wear of guidepieces, there were four mechanisms, namely abrasive wear, adhesive wear, fatigue wear and corrosion wear. The failure analysis to the guide-piece laid the foundation for its remanufacturing. Foundation item: Project(50235030) supported by the National Natural Science Foundation of China     

Acoustic emission method for research and control of friction pairs

One of the new physical methods that provides much information about the processes going on in a friction contact zone in real time is acoustic emission (AE). Basic experimental results of AE in friction are presented and analysed. Using AE signals we can get an indication about the state of the friction processes, about the quality of solid and liquid layers on the contacting surfaces in real time, sometimes about intensity of wear, changing of wear and friction regimes and so on. The influence of sliding velocity, load, roughness and some physical and mechanical properties of the body on the parameters of AE are also given. Some attention to the practical implementation of these techniques for control of capability for work of friction pairs in real conditions are given. Modern methods and devices enable condition monitoring of sliding and rolling bearings.     

Investigations of water inrushes from aquifers under coal seams

In many coal mines, limestone-confined aquifers underlie coal seams. During coal extraction from these mines, water inrushes occur frequently with disastrous consequences. This paper introduces the hydrogeological conditions of the coal mines and the potential water inrush disasters from aquifers under coal seams. It then presents the water inrush mechanism. The main factors which control water inrushes include strata pressure, mining size, geologic structures and the water pressure in the underlying aquifer. Analysis shows that reduction of confinement due to mining is the major cause of the water-conducting failure in the floor strata. The depth of the failure zone is strongly dependent on the mining width. This paper also presents field observation results of the water-conducting failure in the floor strata, and applies the finite element method coupled with stress-dependent permeability to analyze hydraulic conductivity enhancement due to coal extraction. Finally, theoretical and empirical methods to predict water inrushes are given, and technical measures for improving mine design and safety for coal extraction over aquifers are presented. These measures include fault and fracture grouting and mining method modification such as changing long-wall to short-wall mining.     

海底管道系统失效故障树的建立及定性分析

受自然环境、管道腐蚀、第三方破坏及管理不善等因素的影响,海底管道系统在铺设及运行过程中常常会失效。文中以海底管道穿孔、凝管、断裂和设备故障等主要失效形式为顶事件建立了海底管道系统失效故障树,通过系统的定性分析得到了海底管道系统失效故障树的37个一阶最小割集,进而确定了影响海底管道系统失效的4项主要因素,并针对这些主要因素提出了相应的解决问题的措施。