一种新型地雷战斗部的数值模拟研究

针对地雷的毁伤目标和特性,提出一种新颖的多棱柱状药型罩结构,其可看作由八个楔形罩对称排列相邻连接而成。应用非线性有限元软件完成了爆炸载荷下多棱柱状药型罩形成射流过程的数值模拟,结果表明新型药型罩结构能够实现预期设想,形成一股汇聚射流。研究结果为地雷战斗部研究提供了一种新的选择。     

综采工作面巷道内瓦斯分布规律研究

为了研究综采工作面巷道内瓦斯运移规律，摸清瓦斯流动的状态，采用理论分析、数值模拟和现场试验相结合的方法，理论分析得到了工作面风流特性及瓦斯运移规律，数值模拟得到了瓦斯异常释放后工作面瓦斯浓度分布变化情况及工作面正常工作瓦斯浓度分布，然后进行现场试验，试验结果和数值模拟结果相似。研究为工作面瓦斯治理提供了技术支持。     

Continuous Flow Fabrication of Block Copolymer–Grafted Silica Micro‐Particles in Environmentally Friendly Water/Ethanol Media

Polymer‐grafted inorganic particles (PGIPs) are attractive building blocks for numerous chemical and material applications. Surface‐initiated controlled radical polymerization (SI‐CRP) is the most feasible method to fabricate PGIPs. However, a conventional in‐batch reaction still suffers from several disadvantages, including time‐consuming purification processes, low grafting efficiency, and possible gelation problems. Herein, a facile method is demonstrated to synthesize block copolymer–grafted inorganic particles, that is, poly(poly(ethylene glycol) methyl ether methacrylate) (PPEGMEMA)‐b‐poly(N‐isopropylacrylamide) (PNIPAM)–grafted silica micro‐particles using continuous flow chemistry in an environmentally friendly aqueous media. Immobilizing the chain transfer agent and subsequent SI‐CRP can be accomplished sequentially in a continuous flow system, avoiding multi‐step purification processes in between. The chain length (MW) of the grafted polymers is tunable by adjusting the flow time or monomer concentration, and the narrower molar mass dispersity (Р< 1.4) of the grafted polymers reveals the uniform polymer chains on the particles. Moreover, compared with the in‐batch reaction at the same condition, the continuous system also suppresses possible gelation problems.     

不同工质回路热管负载功率变化下的质量流量特性

为了进一步提高回路热管仿真精度并丰富回路热管实验研究方法，本文对回路热管瞬态传质进行实验研究。使用高精度质量流量计分别对以丙酮、乙醇、丙烯为工质的回路热管进行不同负载功率下的质量流量测量研究。结果表明：启动阶段，热负载10W时，丙烯回路比丙酮回路热管启动快，且两者的温度稳定均滞后于质量流量；稳定阶段，随着热负载功率增大，不同工质的回路热管的平均质量流量均线性增长，而瞬态质量流量则持续波动，其质量流量波动幅度均呈现先减小后增大的趋势。质量流量波动幅度会受到气体工质的可压缩性与作用在毛细芯内部上的热量的共同影响。通过频谱分析发现，液相质量流量波动还会受到冷凝器两相区的影响。高热负载下，作用在毛细芯内部上的热量占主导地位，质量流量波动加剧，同时出现周期性大幅波动，且其波动频率随着热负载增大而增大。     

自然循环窄矩形通道内过冷沸腾两相摩擦阻力特性

采用去离子水作为实验工质，在低压低流速自然循环工况下开展了单面加热可视化窄矩形通道内的过冷沸腾摩擦阻力特性实验研究。实验中测量了实验段内的压降数据，并通过高速摄影仪拍摄了窄矩形通道内的气液两相图像，提出了过冷沸腾条件下的两相摩擦压降的剥离计算方法。基于本实验中获得摩擦压降数据，对分别基于均相流模型和分液相模型的经典两相摩擦压降计算关系式进行了评估，实验结果表明：采用不同等效黏度计算方法的均相流模型计算结果比实验值明显偏小；而分相流模型中，Sun and Mishiba关系式和Tran关系式均能够较好地预测摩擦阻力，计算值与实验值的平均相对偏差在±15%以内。结合实验数据，以分相流模型方法为基础，考虑全液相Reynolds数、Martinelli参数和Laplace数的影响，获得了计算分液相折算系数的经验关系式，与实验数据符合较好, 平均相对误差在10%范围内。     

Effects of Winding Attachment Positions on Output Characteristics of Flux‐Modulating Synchronous Machines

The flux‐modulating synchronous machine (FMSM) is a new type of multipole SM with nonoverlapping concentrated armature and field windings on the stator. This paper compares the output characteristics of two FMSMs through finite element analysis (FEA) and experiments. In both of the FMSMs, the attachment positions of the armature and field windings are swapped. To determine the reason for the discrepancies in their output characteristics, unsaturated inductances were calculated using a d‐‐q equivalent circuit. In addition, the calculated results of the inductances were confirmed through a visualization of the leakage fluxes using FEA. The results of the study show that the synchronous inductance can be reduced by attaching the armature winding to the air‐gap side of the stator teeth and that the reduction leads to an increase in output power.     

Effects of the film thickness and poling electric field on photovoltaic performances of (Pb,La)(Zr,Ti)O3 ferroelectric thin film-based devices

The ferroelectric photovoltaic (FPV) effect obtained in inorganic perovskite ferroelectric materials has received much attention because of its large potential in preparing FPV devices with superior stability, high open-circuit voltage (V_oc) and large short-circuit current density (J_sc). In order to obtain suitable thickness for the ferroelectric thin film as light absorption layer, in which, the sunlight can be fully absorbed and the photo-generated electrons and holes are recombined as few as possible, we prepare Pb_0.93La_0.07(Zr_0.6Ti_0.4)_0.9825O₃ (PLZT) ferroelectric thin films with different layer numbers by the sol-gel method and based on these thin films, obtain FPV devices with FTO/PLZT/Au structure. By measuring photovoltaic properties, it is found that the device with 4 layer-PLZT thin film (~300 nm thickness) exhibits the largest V_oc and J_sc and the photovoltaic effect obviously depends on the value and direction of the poling electric field. When the device is applied a negative poling electric field, both the V_oc and J_sc are significantly higher than those of the device applied the positive poling electric field, due to the depolarization field resulting from the remnant polarization in the same direction with the built-in electric field induced by the Schottky barrier, and the higher the negative poling electric field, the larger the V_oc and J_sc. At a -333 kV/cm poling electric field, the FPV device exhibits the most superior photovoltaic properties with a V_oc of as high as 0.73 V and J_sc of as large as 2.11 μA/cm². This work opens a new way for developing ferroelectric photovoltaic devices with good properties.     

On optical flow techniques applied to breaking surges

Surface wave breaking is a challenging two-phase flow process which plays an important role in numerous physical processes. A highly-turbulent unsteady breaking surge was investigated experimentally in a large facility, and substantial aeration occurred in the roller. The application of three optical flow techniques (Lucas-Kanade, Horn-Schunck and Farnback) to the air-water region was tested. The results indicated that the Farnback technique provided most accurate results, although some misleading results could be obtained near the air-water boundaries of the roller. The bore generation by a rapid gate closure showed a highly-unsteady complicated velocity field, with substantial free-surface deformations, wave breaking and formation of large coherent structures before the surge detached from the gate. Further upstream, the surge propagated as a hydraulic jump in translation and the data showed a marked shear region with a recirculation zone above, showing air-water flow features comparable to stationary hydraulic jumps. The upper and lower bounds of air-water flow region yielded data implying an air-to-water velocity ratio about 4–5 for a Froude number Fr₁ = 2.1.     

Research on optimization design of PWR flow distribution device based on numerical simulation

ABSTRACT

In the lower chamber of pressurized water reactor (PWR), the flow distribution device is the core module to distribute coolant into the core. It has complex structure and numerous design parameters. Therefore, it has important theoretical and practical significance to optimize the device. The mesh independence verification, turbulence model selection, and data processing all can influence the numerical simulation results of the lower chamber, in order to research the influence, a numerical simulation method based on the original model of CNP1000 reactor lower chamber is proposed in this paper. In the method, an optimization design method of flow distribution device is established based on surrogate model. The main design variables and optimization objectives are determined based on the device’s structure and function characteristics. And then it respectively adopts Kriging algorithm and multi-objective genetic algorithm to establish a surrogate model of flow distribution device and optimize it globally. Finally, the optimal design variables are obtained. Compared with the device’s performance before optimization, the after optimization has smaller total pressure loss and more uniform flow. The effectiveness and practicability of proposed optimization design method can be verified.     

Transmission system restoration with co-optimization of repairs,load pickups,and generation dispatch

This paper studies the restoration of a transmission system after a significant disruption such as a natural disaster. It considers the co-optimization of repairs, load pickups, and generation dispatch to produce a sequencing of the repairs that minimizes the size of the blackout over time. The core of this process is a Restoration Ordering Problem (ROP), a non-convex mixed-integer nonlinear program that is outside the capabilities of existing solver technologies. To address this computational barrier, the paper examines two approximations of the power flow equations: The DC model and the recently proposed LPAC model. Systematic, large-scale testing indicates that the DC model is not sufficiently accurate for solving the ROP. In contrast, the LPAC power flow model, which captures line losses, reactive power, and voltage magnitudes, is sufficiently accurate to obtain restoration plans that can be converted into AC-feasible power flows. An experimental study also suggests that the LPAC model provides a robust and appealing tradeoff between accuracy and computational performance for solving the ROP.