天然气吸附储存脱附过程的动态模拟

通过热动力学计算,认识了脱附过程当中储罐内温度剖面分布的典型特征:储罐轴心处的温度下降幅度最大。分析了脱附过程当中储罐壁的热交换、吸附剂的导热系数以及储罐内的初始压力对储罐内的温度剖面的影响。结论是加强储罐外壁的热交换、增大吸附剂的导热系数皆能改善吸附储罐内的温度剖面。     

Thermodynamic and Transport Properties of Liquid HFC-227ea

The thermal conductivity and heat capacity of liquid 1,1,1,2,3,3,3-hepta-fluoropropane (HFC-227ea) have been studied by a high-frequency thermal-wave method over the temperature range of 294 to 345 K at pressures up to 2.8 MPa. The purity of the samples used throughout the measurements is 99.99 mol%. The experimental uncertainties of the thermal conductivity and heat capacity measurements were estimated to be within ±1.5 and ±2%, respectively. The thermal conductivity of HFC-227ea in the liquid phase decreases as temperature increases, while the pressure has an opposite effect.     

混合乳化剂的优选及抗高低温水包油钻井液的研制

O/W乳化钻井液用的阴离子/非离子混合乳化剂,其中的非离子乳化剂先用PIT法初选,再以O/W乳状液黏度为性能指标,用HLB法选定,其中的阴离子乳化剂也用HLB法筛选。选定的一对非离子和阴离子乳化剂按不同比例复配,利用混合表面活性剂HLB值的加和性原理,由O/W乳状液黏度-HLB值关系确定二者最佳配比。O/W乳化钻井液以体积比70/30的柴油 原油为油相,油水相体积比40/60-60/40,乳化剂加量为油水总体积的4%-7%,加入的主要处理剂有:一种代替膨润土的成胶剂,抗高温液体抑制剂,油溶性储层保护剂,降滤失剂等。该钻井液在180℃、最高压力2.5 MPa下热处理24小时或在-26℃冷冻24小时后解冻,均不发生破乳,性能不恶化;用-26℃冷冻7天的乳化剂配制的钻井液,常温和热处理后性能良好。该钻井液流变性能良好,动塑比0.23-0.60,静切力2-8/2-10 Pa,滤失量为零,抑制性良好。图1表3参4。     

炼油厂余热发电的方案选择与应用

介绍了延长石油集团公司榆林炼油厂利用异步发电机组和同步发电机组回收催化裂化装置余热余能的情况,通过对两种回收方法的技术途径、设备配置、实际应用效果和经济效益分析,得出异步发电机组的余热发电技术方案是优选方案的结论.     

600 A IGBT开关电路及其散热系统设计

采用IGBT开关电路，对大功率电阻带进行直流脉宽调制控制，实现了内燃机车大功率直流发电机负载实验中的负载大小的连续调节。为了避免在实验过程中IGBT器件的温度过高，采用独特的双管IGBT结构和双向强迫风冷的散热系统。实验表明该电路运行稳定、可靠。     

换热器设计中适宜流体用量的确定

利用换热器的操作线来分析讨论流体用量对传热过程的操作费用和设备费用的影响，找出了换热器设计和选型中适宜流体用量的优化确定方法，简便，快捷，具有一定的适用性。     

氟塑料—石墨板式换热器在高温强腐蚀换热工况中的应用

通过氟塑料－石墨板式换热器在化纤生产中高温强腐蚀换热工况中的实际应用，并与常规换热器的使用情况的对比分析，阐述了这种新型换热设备的特点。     

金属换热器选用经济分析

本文以系统节能和提高综合经济效益的观点，分析了金属换热器传热系数的影响因素及提高途径；气流阻力与动力消耗；传热面积与投资的定量关系。为正确选用不同结构金属换热器及其性能提供了依据。     

Modeling of Diffusion in Capillary Porous Materials During the Drying Process

This paper presents a model of heterogenous diffusion in capillary porous materials during the process of drying. The governing heat and mass transfer equations have been established using the liquid as well as vapor flow. Two models have been presented. Model 1 does not consider the heat conduction while the model 2 has been established by considering the conduction. The developed models and the numerical solutions of the resulting differential equations can take into account the moisture and temperature dependent thermophysical properties of the product. All equations have been established in spherical coordinates but the programme written for the purpose of calculations can be used for other geometries also. Numerical calculations have been performed for gas concrete and tiles using model 1, while model 2 has been used for gas concrete only because of the lack of data for thermophysical properties of the tile. For gas concrete it was seen that conduction has only marginal effect on the drying process and the numerical predictions of the drying process were reasonably accurate.