客车涂装底层材料配套性分析

针对南方客户在使用我司客车一段时间后，车身涂层不同程度出现了起泡的质量问题，进行了现场查看，发现起泡位置在车身左右侧蒙皮，且发生在涂层最底层。初步分析原因是热镀锌板+阴极电泳漆 +原子灰三者之间配套存在问题，通过热镀锌板 +阴极电泳漆 +原子灰三者之间的耐高温 80 ℃配套试验，以及室外曝晒试验，得出镀锌板表面是否钝化、电泳漆膜致密程度和原子灰苯乙烯含量是造成涂层底层起泡的主要原因。为了控制涂层起泡问题，重新修订了我司原子灰、镀锌板、电泳漆的技术标准以及部分工艺文件。     

负载羧基化球状介孔纳米颗粒TFN膜的研究

在薄层复合膜(thin-film composite membrane, TFC膜)中引入无机纳米颗粒，形成薄层纳米复合膜(thin-film nanocomposite membrane, TFN膜)，近几年作为反渗透膜开始应用于水处理研究。但是无机纳米颗粒在TFC膜中的性能的不稳定性和膜的机械强度等变成了突出问题。合成制备了粒径约为110 nm修饰羧基的介孔氧化硅球状纳米颗粒(MSN—COOH)，并将其成功地化学键合在TFC膜的表面功能层交联网络中。与TFC膜相比，键合有MSN—COOH的TFN膜，水通量提高了56.2%，保持高脱盐率；由于单分散介孔纳米颗粒表面亲水官能团的引入，使膜表面的亲水性有很大程度提高，单分散介孔纳米颗粒在基体中的有序排列，使膜表面粗糙度降低，提高了膜的抗污染能力。与普通TFN膜相比较，具有更好的稳定性和柔韧性，可以在长时间高压过滤操作下保持稳定。     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

高性能有机氟材料制备科学及应用进展

有机氟材料具有优异的热氧稳定性、耐化学腐蚀性、耐老化性、不黏性、电绝缘性以及极小的摩擦系数等特性，因此作为一种不可替代的材料广泛应用于高新技术产业。近年来高新技术产业发展对高性能有机氟材料的需求引发了学术界和工业界对氟材料的研究兴趣。依据本文作者的研究经历及有机氟材料的发展方向，本文介绍了氟树脂（新型含氟聚合物、电活性含氟聚合物、新型全氟磺酸聚合物、聚四氟乙烯3D打印）及氟橡胶（过氧化物硫化氟橡胶、耐低温氟醚橡胶、耐高温全氟醚橡胶、全氟聚醚基类玻璃橡胶）的制备科学及应用进展，特别阐述为了满足航空航天、能源、信息等高新技术产业需求发展的新一代高性能有机氟材料。本文也介绍了近期出现的聚四氟乙烯新成型技术及类玻璃氟橡胶。文章指出发展绿色环保和高效的高性能有机氟材料制备及成型加工方法是今后的发展方向。     

Research on optimization design of PWR flow distribution device based on numerical simulation

ABSTRACT

In the lower chamber of pressurized water reactor (PWR), the flow distribution device is the core module to distribute coolant into the core. It has complex structure and numerous design parameters. Therefore, it has important theoretical and practical significance to optimize the device. The mesh independence verification, turbulence model selection, and data processing all can influence the numerical simulation results of the lower chamber, in order to research the influence, a numerical simulation method based on the original model of CNP1000 reactor lower chamber is proposed in this paper. In the method, an optimization design method of flow distribution device is established based on surrogate model. The main design variables and optimization objectives are determined based on the device’s structure and function characteristics. And then it respectively adopts Kriging algorithm and multi-objective genetic algorithm to establish a surrogate model of flow distribution device and optimize it globally. Finally, the optimal design variables are obtained. Compared with the device’s performance before optimization, the after optimization has smaller total pressure loss and more uniform flow. The effectiveness and practicability of proposed optimization design method can be verified.     

Improved error performance for generalised spatial modulation with enhanced spectral efficiency

The existing analytical average bit error rate (ABER) expression of conventional generalised spatial modulation (CGSM) does not agree well with the Monte Carlo simulation results in the low signal‐to‐noise ratio (SNR) region. Hence, the first contribution of this paper is to derive a new and easy way to evaluate analytical ABER expression that improves the validation of the simulation results at low SNRs. Secondly, a novel system termed CGSM with enhanced spectral efficiency (CGSM‐ESE) is presented. This system is realised by applying a rotation angle to one of the two active transmit antennas. As a result, the overall spectral efficiency is increased by 1 bit/s/Hz when compared with the equivalent CGSM system. In order to validate the simulation results of CGSM‐ESE, the third contribution is to derive an analytical ABER expression. Finally, to improve the ABER performance of CGSM‐ESE, three link adaptation algorithms are developed. By assuming full knowledge of the channel at the receiver, the proposed algorithms select a subset of channel gain vector (CGV) pairs based on the Euclidean distance between all CGV pairs, CGV splitting, CGV amplitudes, or a combination of these.