Ti-6-22-22S合金步进轧制工艺加工棒材研究

采用步进轧制工艺制备了Ti-6-22-22S合金Ф50mm棒材，对加工、热处理、组织与性能的关系进行了分析。结果表明：在两相区上部温度960℃轧制获得细网篮组织，棒材性能较好且数据均匀；热处理后，得到双态组织，强度．塑性达到优良组合，而片层状组织强度较高，但塑性稍低。     

基于SOCKS协议的IPv6/IPv4转换器

介绍了IPv6协议出现和IPv6和IPv4将长期共存的必然性。讨论了从IPv4到IPv6的各种过渡机制，包括IPv4网络中IPv6域间互联的机制及IPv6节点及IPv4节点间通信的机制。实现了一个IPv6／IPv4转换器，该转换器利用了SOCKS协议和6to4隧道方式。最后分析了这个转换器的适用性和特点。     

Perceived risk for influenza in veterans with spinal cord injuries and disorders.

Objective: Guided by the extended parallel process model (EPPM), the objective was to assess control processes dominant in influenza behavior decisions. Design: Cross-sectional survey. Results: Response rate was 31% (n=968). Regarding influenza risk, 59% were in danger control. Those in fear control were more likely to report influenza infection (p=.000). In the nonvaccinated, those in fear control were more likely to indicate not knowing where to get the vaccine (p=.016) and that it was unavailable (p=.027), and those in danger control believed they did not need it (p=.023). Zero critical values were more likely to indicate that no health provider recommended the shot (p=.002). Conclusions: Most perceived efficacy to be stronger than threat related to influenza; according to the EPPM, they are aware of their risk but recognize their ability to avert it. For those in danger control, messages should focus on increasing perceptions of severity and susceptibility to positively affect behavior change. For those in fear control, messages should focus on efficacy only. With a critical value of zero, no threat is induced, and a high-threat/high-efficacy approach should be taken. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Na-MMT对MCPA6／PPO原位共混体系的影响

采用水辅助分散钠基蒙脱土（Na—MMT）通过原位共混的方法制备了浇铸尼龙6（MCPA6）和聚苯醚（PP0）共混物（95／5）。通过SEM、TEM和流变等考察了非常少量的Na-MMT对共混物形貌的影响。结果发现，PP0在MCPA6基体中尺寸从几十微米下降到一个微米左右，且所有的Na-MMT都分散在MCPA6基体中。DSC分析表明PPO分散相的尺寸影响了MCPA6的结晶行为。相比于纯的MCPA6，PPO和Na-MMT的协同作用提高了纳米复合材料的强度和韧性。     

IPv6 delay and loss performance evolution

Although packet delay and loss are two important parameters of the Internet performance, to the best of our knowledge, the evolution of large‐scale IPv6 delay and loss performance has previously not been studied. In this paper, we analyze more than 600 end‐to‐end IPv6 paths between about 26 testboxes of RIPE Network Coordination Centre over two years, and compare the delay and loss performance over time with their IPv4 counterparts. We present and discuss the measurement methodologies and show that IPv6 paths have a higher delay and loss than their IPv4 counterparts. The main reason for the worse performance stems from IPv6‐in‐IPv4 tunnels rather than from native IPv6 paths and such tunnels are still widely used today. Copyright © 2007 John Wiley & Sons, Ltd.     

Austenitizing treatment influence on the electrochemical corrosion behavior of 0.3C-14Cr-3Mo martensitic stainless steel

Effects of austenitizing treatment temperatures on aqueous corrosion properties of martensitic stainless steels were investigated by electrochemical tests (potentiodynamic test, potentiostatic test and electrochemical impedance spectroscopy), and surface analyses (optical microscopy and XRD). The results of potentiodynamic test revealed that the breakdown potential increased with the increased austenitizing temperature, indicating increased relative resistance to initiation of localized corrosion. EIS measurements showed that MSS3 (1030 °C) exhibits larger polarization resistance value than MSS1 (970 °C) and MSS2 (1000 °C) at passive and breakdown states. This was caused by decreasing the amount of Cr-rich M₂₃C₆ carbide which acts as preferential sites for pitting corrosion.     

兼容IPv4及IPv6的网络程序设计

介绍了在Window系统中设计兼容IPv4及IPv6的网络程序的方法,并给出了用WinsockAPI编程的具体步骤。     

纤维体积分数对K3D/MCPA复合材料力学性能的影响

本文研究了纤维体积分数对三维编织芳纶纤维增强铸性尼龙(简称K3D／MCPA)复合材料力学性能的影响。研究表明，K3D／MCPA复合材料有优异的抗冲击性能，冲击强度比三维编织芳纶纤维增强铸性尼龙(简称C3D／MCPA)和纯基体均有大幅度的提高，且随着纤维体积的提高而升高。K3D／MCPA复合材料剪切强度随纤维体积比的增大而增大，其纵向剪切强度低于纯基体和C3D／MCPA复合材料，但其横向剪切强度高于它们。K3D／MCPA复合材料弯曲强度与弯曲模量随纤维体积比的提高而提高，但与相同体积比的C3D／MCPA相比，K3D／MCPA的弯曲强度与弯曲模量均较低。     

Influence of Ni Interlayers on the Mechanical Properties of Ti6Al4V/(WC-Co) Friction Welds

Ni interlayers were introduced prior to dissimilar friction welding of Ti6Al4V base material to three cemented carbide substrates. The fracture strength of Ti6Al4V/(WC-6 wt% Co) welds were poor and were markedly improved when 20-µm thick Ni interlayers were introduced prior to dissimilar friction welding. These results were only produced when the (WC-6 wt% Co) cermet was electroplated prior to friction welding. When the Ti6Al4V alloy was electroplated prior to friction welding, fractured WC particles and cracking were observed in the (WC-Co) carbide substrate. The fracture strengths of Ti6Al4V/(WC-11 wt% Co) and Ti6Al4V/(WC-24 wt% Co) welds were not improved when 20-µm thick Ni interlayers were introduced prior to friction welding. During mechanical testing, the Ni layer retained at the dissimilar joint interface created a region of weakness.