Ultrasmall rhodium nanoclusters anchored on nitrogen-doped carbon nanotubes with embedded nickel nanoparticles as magnetically recyclable catalysts for efficient ammonia-borane hydrolysis

Facile yet efficient synthesis of high-performance nanocatalysts for hydrogen evolution from ammonia-borane (AB) hydrolysis is paramount. Here, we reported a novel hybrid nanocatalyst comprised of Rh nanoclusters (1.56 nm in diameters) anchored on nitrogen (N)-doped carbon nanotubes with embedded Ni nanoparticles (Ni@NCNTs), which was fabricated through adsorption of Rh ions on Ni@NCNTs. The achieved hybrid of Rh/Ni@NCNTs displayed excellent catalytic property (Turnover frequency: 959 min⁻¹) toward AB hydrolysis, higher than many prior developed Rh-based catalysts. Note that this hybrid could be reused for at least nine runs with complete AB conversion to hydrogen. Rh nanoclusters with small size exhibiting high atom utilization and the synergetic effect between Ni and Rh are responsible for the excellent catalytic property of Rh/Ni@NCNTs toward AB hydrolysis. This work highlights the importance of utilization of magnetically recyclable Ni@NCNTs as support and synergetic component for efficient hydrolysis of AB.     

Calorimetric study of ytterbium orthovanadate YbVO4 polycrystalline ceramics

The heat capacity of ytterbium orthovanadate was first measured by adiabatic calorimetry in the temperature range T?=?12.28–344.06?K. No obvious anomalies were observed on the curve obtained. The values of standard thermodynamic functions in the temperature range T?=?0–400 K were calculated. Based on low-temperature calorimetry data obtained, previously published data on the high-temperature heat capacity of ytterbium orthovanadate were corrected. The anomalous contribution to heat capacity for YbVO₄ was compared with the data known for YbPO₄.     

The influence of activated carbon as an additive in anode materials for low temperature solid oxide fuel cells

The effects of activated carbon (AC) as an additive in multi-oxide nano composite LiNiCuZn–O for application as anode in solid oxide fuel cell (SOFC) is reported. The composite was synthesized using solid state reactions method with varying content of AC in range 0.1%–0.9% for use as anode in the cell. The cell was composed of the synthesized composite as anode, LiNiCuZn–O as cathode and Samaria doped ceria (SDC) as electrolyte. The prepared composites were characterized for morphology and crystal structure by scanning electron microscope (SEM) and x-ray diffraction (XRD) respectively. Furthermore, the crystallite sizes of LiNiCuZn–O and LiNiCuZn–O with AC as an additive have been found in the range from 50 nm to 70 nm. The prepared composite materials were observed porous and the porosity of the sample having 0.5% additive was found highest. The conductivity and power density of the SOFC were studied at temperature of 600 °C. The maximum value of conductivity was found as 4.79 S/cm for the composite containing 0.5% AC as measured by using 4-probe method. The maximum value of power density of the fuel cell with anode comprising of 0.5% AC along with the mentioned cathode and the electrolyte was 455 mW/cm². Therefore, out of the compositions studied, the composite comprising of LiNiCuZn–O with 0.5% AC offered best performance for anode in the cell. This oxide composite is reported as a potential candidate for use as anode in low temperature SOFCs.     

Multiplex PCR system to track authorized and unauthorized genetically modified soybean events in food and feed

A diverse range of genetic elements has been used to develop genetically modified organisms (GMOs) over the last 18 years. Screening methods that target few elements, such as the Cauliflower Mosaic Virus 35S promoter (P-35S) and Agrobacterium tumefaciens nopaline terminator (T-nos), are not sufficient to screen GMOs. In the present study, a multiplex PCR system for all globally commercialized GM soybean events was developed to easily trace the events. For this purpose, screening elements of 24 GM soybean events were investigated and 9 screening targets were selected and divided into three individual triplex PCR systems: P-35S, ribulose-1,5-bisphosphate carboxylase small subunit promoter of Arabidopsis thaliana, T-nos, T-35S, pea E9 terminator, open reading frame 23 terminator of A. tumefaciens, proteinase inhibitor II terminator of potato, acetohydroxy acid synthase large subunit terminator of A. thaliana, and the revealed 3′ flanking sequences of DP-305423-1. The specificity of the assays was confirmed using thirteen GM soybean events as the respective positive/negative controls. The limit of detection of each multiplex set, as determined using certified reference materials of specific GM events, ranged from 0.03 to 0.5%, depending upon target. Furthermore, 26 food samples that contained soybean ingredients, which were purchased from the USA, China, Japan, and Korea, were analyzed, 17 of which contained one or more GM soybean events. These results suggest that the developed screening method can be used to efficiently track and identify 24 GM soybean events in food and feed.     

CO2 abatement and CH4 recovery at vehicle exhausts: Comparison and characterization of Ru powder and pellet catalysts

The catalytic conversion of CO₂ to CH₄ (Sabatier reaction) has been studied to develop an after-treatment process at vehicles exhausts. Three different formulations of Ru commercial catalysts, two in powder and one in pellets shape, were tested and characterized by means of X-ray powder diffraction, scanning electron microscopy (SEM-EDX), N₂ adsorption at −196 °C and temperature-programmed reduction (TPR).Experimental results show a high CO₂ conversion (X_CO2 = 0.96 @ T = 280 °C) for one powder catalyst formulation whereas the other one has maximum CO₂ conversion = 0.69. In both cases a high CH₄ selectivity is measured. High CO₂ conversion (X_CO2 = 0.92 @ T = 300 °C) is obtained also with pellet catalysts but only at lower GHSV values. The different behavior of the catalysts was ascribed to the different physicochemical properties and the key parameters for the application development of the process were identified. In particular, the possibility to use pellets or monolithic reactors, thus minimizing the pressure drops in the reactor, makes possible a commercial application in the treatment of vehicles exhausts.     

酸性废水中As(Ⅲ)、Cu(Ⅱ)与铁粉的反应行为

在Fe-As(Ⅲ)-Cu(Ⅱ)-H₂O体系中, 研究了酸性废水中As(Ⅲ)、Cu(Ⅱ)与金属铁粉的反应行为, 考察了反应过程中As在气、液、固三相中的分配比。结果表明, As(Ⅲ)和Cu(Ⅱ)离子被Fe还原为单质As和Cu后, As、Cu进一步结合成Cu₅As₂等金属间化合物, 从而促进As(Ⅲ)沉淀反应的发生, 且无AsH3生成。在反应时间40min、铁粉过量系数1.2、溶液初始pH=0.0、温度40 ℃、Cu/As摩尔比1.0条件下, As在气、液、固三相中的分配比分别为0、20.7%和79.3%, 沉砷率为79.3%。     

Development of mobile miniature natural gas liquefiers

With increasing consumption of natural gas (NG), small NG reservoirs, such as coalbed methane and oil field associated gas, have recently drawn significant attention. Owing to their special characteristics (e.g., scattered distribution and small output), small-scale NG liquefiers are highly required. Similarly, the mixed refrigerant cycle (MRC) is suitable for small-scale liquefaction systems due to its moderate complexity and power consumption. In consideration of the above, this paper reviews the development of mobile miniature NG liquefiers in Technical Institute of Physics and Chemistry (TIPC), China. To effectively liquefy the scattered NG and overcome the drawbacks of existing technologies, three main improvements, i.e., low-pressure MRC process driven by oil-lubricated screw compressor, compact cold box with the new designed heat exchangers, and standardized equipment manufacturing and integrated process technology have been made. The development pattern of “rapid cluster application and flexible liquefaction center” has been eventually proposed. The small-scale NG liquefier developed by TIPC has reached a minimum liquefaction power consumption of about 0.35 kW·h/Nm³. It is suitable to exploit small remote gas reserves which can also be used in boil-off gas reliquefaction and distributed peak-shaving of pipe networks.     

Investigation of flame spray synthesized La1-xSrxCoO3 perovskites with promotional catalytic performances on CO oxidation

To enhance the activity of catalysts for CO removal, the perovskite-type catalysts La_1-xSr_xCoO₃ (x = 0, 0.2, 0.4, 0.6, and 0.8) with different Sr²⁺ doping amount were synthesized by flame spray synthesis (FSS) method. The perovskite-type catalyst synthesized by FSS has a much larger specific surface area (SSA) than that prepared by other conventional methods. The SSA of catalyst increases with the increase of Sr²⁺ doping amount and the SSA of La_0.2Sr_0.8CoO₃ reaches 31.65 m²/g. Compared with other conventional methods, FSS method significantly improves the activity of catalyst and makes it close to the performances of catalysts with surface modification. The substitution of La³⁺ by Sr²⁺ promotes the generation of secondary phase Co₃O₄ and SrCO₃. The catalytic activity of La_1-xSr_xCoO₃ increases with the addition of Sr²⁺, which results from the increasing active sites and oxygen vacancies. Interestingly, La_0.4Sr_0.6CoO₃ performs the highest activity for CO oxidation and the CO conversion reaches 50% at 148.6 °C and 90% at 165.9 °C. The oxidation of CO over La_1-xSr_xCoO₃ catalyst may follow a combination of MvK and L-H mechanisms according to the experimental results of H₂-TPR. Moreover, the catalyst exhibits good catalytic activity in consecutive oxidation cycles. In consecutive oxidation experiments with La_0.4Sr_0.6CoO₃, the CO conversion reaches 50% at 168.8 °C and 90% at 197.8 °C in the eighth oxidation cycle. These results prove that FSS method can further improve the activity of catalysts and is suitable for the preparation of efficient catalysts.     

Investigations on Selectivity of Gas-Liquid Reactions in Capillaries

Biocatalysis offers a broad spectrum of possible ecological and economic advantages over conventional chemical catalysis processes, e.g., lower energy consumption and high enantio selectivity. The focus of this work is on gas-liquid reactions. These are of great importance in the chemical and biochemical industry and subject of current research since they are often limited by mass transfer or show low selectivity. Different suitable biocatalytically gas-liquid reaction systems were tested in capillary reactor designs in order to obtain information about the interaction between reaction and fluid mechanics. Furthermore, an optical measuring method was established. The experiments were performed in batch mode in a glass beaker with a flow cuvette for UV/Vis measurement of product concentration.