A new ‘Tailor-made’ methodology for the mechanical behaviour analysis of rubber-like materials: II. Application to the hyperelastic behaviour characterization of a carbon-black filled natural rubber vulcanizate

The purpose of this paper is the modelling of the mechanical behaviour of an elastomeric material, through detailed experimental and numerical procedures, specific to large strains. The experimental technique is based on in-plane kinematics measurements using a speckle extensometer, from which the whole two-dimensional field of in-plane displacements is obtained by a digital image processing [Polymer (2002)]. This part of the work concerns the identification of the constitutive equation for a carbon black natural rubber (NR) vulcanizate. We start by quoting some theoretical considerations relative to rubber elasticity and stress-softening effect, which is the counterpart of the filler reinforcement. Then, we describe the experimental procedure and present data for both non-preconditioned and preconditioned samples. Next, the identification of the constitutive law parameters using a minimization algorithm is driven. Finally, we present the validation of the constitutive model, by its implementation into the finite element code SYSTUS and the numerical simulation of the response of a double edge notched tensile (DENT) specimen.     

Recovery of monomers and fillers from high-temperature-vulcanized silicone rubbers—combined effects of solvent, base and fillers

The depolymerization of high-temperature-vulcanized (HTV) silicone rubbers containing filler silica and alumina into cyclosiloxane monomers and spontaneous recovery of fillers were studied. First, HTV silicone rubber was treated with different types of solvents in the presence of KOH to find that a triad mixture of diethylamine, methanol and hexane was appropriate not only to dissolve the silicone rubber to a suspension but also to separate fillers completely by filtration. The filtrate was distilled to remove solvent first and then give pure cyclosiloxane monomers in 76–84% yields. Second, the rubbers were treated with other types of triad mixture of solvents and bases, e.g. tetramethylammonium hydroxide, hexane and diethylamine. After filtration, residue was again treated with the amine and hexane to recover clean fillers in 83–93% yields. Cyclosiloxane monomers were also obtained from the combined filtrates in 67–78% yields.     

半导体ZnTe/GaAs界面层错的高分辨显微分析

本项研究对经热壁外延（ＨＷＥ）生长在ＧａＡｓ基底上的ＺｎＴｅ进行分高分辨显微结构的观察，在ＺｎＴｅ／ＧａＡｓ界面上不仅存在着混合型全位错的扩展，而且首次发现类似螺旋位错分解的层错，并将其归结为原子在不全位错之后的堆积。     

Al(OH)3对硅橡胶性能的影响

综述了Al（OH)3粒径和用量对硅椽胶漏电电流、脉冲电流、耐漏电起痕、表面粗糙程度、电蚀损、介电性能、拉伸强度及漏电电流实验重复性的影响。     

新型难燃输送带胶粘剂的研制

以改性氯丁橡胶为主料、多异氰酸酯为固化剂制成的新型难燃输送带胶粘剂,具有粘接强度高、耐热性好、干燥时间短、难燃等特点,在常温常压下粘接输送带接头,固化30min即可负荷运行。     

Investigations of surface characterization of silicone rubber due to tracking phenomena under a.c. and d.c. voltages

In the present work, tracking phenomena has been studied with silicone rubber material under the a.c. and d.c. voltages following IEC-587 standards. The surface condition of the tracked zone was analysed using wide angle X-ray diffraction (WAXD) and thermogravimetric differential thermal analysis (TG-DTA) studies. The tracking time was different for a.c. and d.c. voltages.     

Thermoplastic elastomeric composition based on maleic anhydride–grafted ground rubber tire

Ground rubber tire (GRT) powder was maleated in an internal mixer using maleic anhydride and dicumyl peroxide at 160°C. Maleated GRT was characterized by using X‐ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, wettability, and differential scanning calorimetry. The physical properties of the dynamically vulcanized 60 : 40, rubber : plastic composition based on acrylated high‐density polyethylene as the plastic phase and ethylene propylene diene rubber containing maleated GRT as the rubber phase were found to be greater than the corresponding composition containing nonmaleated GRT. The blend was found to be reprocessable, like themoplastic elastomers. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 370–378, 2002; DOI 10.1002/app.10348