纤维状海泡石对环氧树脂反应性的影响研究

使用海泡石制备环氧树脂纳米复合材料。采用胶化时间、热分析方法、红外光谱法研究纤维状海泡石对环氧树脂反应性的影响。用透射电镜观察海泡石的分散情况,通过力学性能的测试,研究海泡石对环氧树脂基体力学性能的影响。结果表明,海泡石对环氧树脂的工艺性没有影响,可使环氧树脂的力学性能大幅度提高。     

Enhanced corrosion prevention effect of polysulfone–clay nanocomposite materials prepared by solution dispersion

A series of polymer–clay nanocomposite (PCN) materials containing polysulfone (PSF) and layered MMT clay were successfully prepared by effectively dispersing inorganic nanolayers of MMT clay in an organic PSF matrix via a solution dispersion technique. The synthesized PCN materials were subsequently investigated with a series of characterization techniques, including Fourier transform infrared (FTIR) spectroscopy, wide‐angle powder X‐ray diffraction (XRD) and transmission electron microscopy (TEM). The prepared PCN coatings with low clay loading (1 wt %) on cold‐rolled steel (CRS) were found to be superior in corrosion prevention to those of bulk PSF, based on a series of electrochemical measurements of corrosion potential, polarization resistance, corrosion current and electrochemical impedance spectroscopy (EIS) in a 5 wt % aqueous NaCl electrolyte. The effects of material composition on the molecular barrier, mechanical strength and optical clarity of PSF and PCN materials, in the form of membranes, was also studied by molecular permeability analysis (GPA), dynamic mechanical analysis (DMA) and UV‐Visible transmission spectra, respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 631–637, 2004     

Potential for use of crushed waste calcined-clay brick as a supplementary cementitious material in Brazil

The Brazilian ceramic industry generates large amounts of calcined-clay waste. This paper examines the factors that influence its potential for use as a partial replacement of Portland cement. Superplasticized mortars of equal workability containing ground crushed waste calcined-clay brick (GCWCCB) in the proportions of 10, 20, 30 and 40% as a cement replacement were analyzed through mechanical tests, pore structure characterization and durability tests. The results indicated the optimal percentages of substitution lies between 10% to 20%. The potential reduction of CO₂ emissions could be as high as 10% of current Brazilian cement industry emissions if this approach were to be fully implemented, and it could be eligible for “Clean Development Mechanism” credits under Kyoto protocol.     

钾长石含量对硬质粘土烧结的影响

以硬质粘土粉(w(Al2O3)>38%,粒度为0.002～0.11mm)和钾长石粉(w(K2O Na2O)=13.13%,粒度为0.005～0.11mm)为原料,配制成钾长石粉加入量分别为0、3.76%、5.30%和6.84%的试料(对应的w(K2O Na2O)分别为0.11%、0.6%、0.8%和1.0%),湿磨2h,烘干后以150MPa压力压制成20mm×10mm的试样,然后在1500～1600℃煅烧3h。对煅烧后试样进行了物理性能检测、物相分析和显微结构分析,以研究钾长石含量对粘土烧结的影响。结果表明:钾长石粉加入前后试样的烧结温度分别为1550℃和1500℃;加入钾长石能消除粘土原料煅烧过程中形成的方石英相,使烧成试样中只出现莫来石晶相;加入3.76%～6.84%钾长石粉的试样中莫来石含量达61%～66%,并且莫来石发育较好,呈针状,长度达8μm,直径约0.5μm。     

Bulk polymerization of styrene in the presence of organomodified montmorillonite

The effect of montmorillonite (Cloisite 6A) on the bulk polymerization of styrene initiated by benzoyl peroxide (BPO) was studied by the dilatometric determination of the polymerization rates. The bulk polymerization rates increased as the montmorillonite input quantity increased. The effect became greater when the BPO concentration decreased. Under the assumption that clay participated in the radical initiation reaction of the chains, the reaction orders for clay and BPO were determined to be approximately 1.0 and 0.5, respectively. X‐ray diffraction and thermogravimetric analysis studies showed that the structure and properties of the obtained polystyrene (PS)/montmorillonite nanocomposites were greatly affected by the BPO concentration. With lower BPO concentrations, a larger interlayer distance and a higher extent of delamination for the clay were observed in the obtained PS/montmorillonite nanocomposites. The nanocomposites prepared with lower BPO concentrations also showed higher heat‐decomposition‐resistance temperatures. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1146–1152, 2005     

Morphology and thermal stability of BR/clay composites prepared by a new method

A new potential preparation method named in situ organic modification was used to prepare intercalated polybutadiene rubber (BR)/clay/dimethyl dihydrogenated tallow ammonium chloride (DDAC) composites. That is, BR, pristine clay, and intercalatant DDAC were directly mixed in a Haake rheometer without pretreating the pristine clay with the intercalatant. The morphology of the BR/clay composites was investigated by means of X‐ray diffraction and scanning electron microscopy. The thermal stability of the BR/clay composites was analyzed by thermogravimetric analysis (TGA). The dispersion of clay particles in the BR/clay/DDAC composites is much better than that in the BR/pristine clay and similar to that in the BR/organoclay DK4 (modified with DDAC) composites. BR/clay/DDAC composites have much higher thermal stability than the gum BR, BR/pristine clay, and BR/DK4 composites. The clay/intercalatant ratio has little influence on the thermal stability of the BR/clay/DDAC composites, while clay content has a significant effect on their thermal stability. The enhanced thermal stability of the BR/clay/DDAC composites is related to the dispersion state of clay particles in BR. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 905–913, 2006     

聚苯并双噁唑类聚合物的合成及改性

简述了聚对苯撑苯并双(?)唑(PBO)的合成方法,详述了直链烯烃型、稠环芳烃型、联苯取代基型、杂环型聚苯并双(?)唑类聚合物的合成方法。综述了等离子体处理法、偶联剂处理法、电晕处理法等一系列PBO纤维表面改性技术的研究进展,通过介绍PBO／碳纳米管复合材料和PBO／粘土复合材料的合成技术,简析了PBO的纳米改性的研究。指出聚苯并双(?)唑聚合物研究将集中在合成高相对分子质量的聚合物合成技术,通过纳米改性及表面改性提高其性能,扩大应用领域。     

Thermoplastic olefin/clay nanocomposites: Morphology and mechanical properties

Thermoplastic olefin (TPO)/clay nanocomposites were made with clay loadings of 0.6–6.7 wt %. The morphology of these TPO/clay nanocomposites was investigated with atomic force microscopy, transmission electron microscopy (TEM), and X‐ray diffraction. The ethylene–propylene rubber (EPR) particle morphology in the TPO underwent progressive particle breakup and decreased in particle size as the clay loading increased from 0.6 to 5.6 wt %. TEM micrographs showed that the clay platelets preferentially segregated to the rubber–particle interface. The breakup of the EPR particles was suspected to be due to the increasing melt viscosity observed as the clay loading increased or to the accompanying chemical modifiers of the clay, acting as interfacial agents and reducing the interfacial tension with a concomitant reduction in the particle size. The flexural modulus of the injection moldings increased monotonically as the clay loading increased. The unnotched (Izod) impact strength was substantially increased or maintained, whereas the notched (Izod) impact strength decreased modestly as the clay loading increased. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 928–936, 2004     

Mechanical properties and structures of dicyanate–clay nanocomposites

Dicyanate–clay nanocomposites comprising a dicyanate resin and a type of organically modified clay were prepared and characterized, and their thermomechanical properties were investigated. The organically modified clay had silicate layers of nanometer size intercalated with an organic modifier, which improved the compatibility between the clay and organic materials, such as dicyanate resins. Dynamic mechanical analysis was performed to investigate the thermomechanical properties of the dicyanate–clay nanocomposites containing various amounts of the clay. The storage modulus of the nanocomposites below their glass‐transition temperatures slightly increased with increasing clay content. The glass‐transition temperature of the dicyanate–clay nanocomposites increased with increasing clay content. The nanostructures of the dicyanate–clay nanocomposites were characterized by transmission electron microscopy and X‐ray diffraction analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2629–2633, 2003     

粘土改性环氧树脂浆液冲蚀磨损研究

研究了粘土改性环氧树脂的浆液体冲蚀磨损性能。研究表明:不同粘土加入量的改性环氧树脂的冲蚀磨损率随冲蚀角度的变化规律相同,变化曲线呈W形,材料表现出从脆性材料向塑性材料过渡的冲蚀磨损特征;粘土改性环氧树脂的冲蚀磨损率随粘土加入量增加而降低,但磨损率下降不是线性的,当粘土加入量在0~1%之间时环氧树脂的磨损率下降速度大,而随着粘土加入量进一步升高,环氧树脂磨损率降低速度缓慢。