影响凹印铜金粉印金光泽度的主要因素

在研究国内外铜金粉的微观形貌、厚度、水面遮盖率、定向排列、光泽度和粒度分布的基础上，分析了影响凹印铜金粉印金光泽度的主要因素。结果表明，国产铜金粉颗粒级差大、细小颗粒所占比例过多、金属片太厚、水面遮盖率小、定向排列不好等是影响国产铜金粉印金光泽度的主要因素。     

小型办公网络组网

通过实例,对小型办公网络组网中涉及到的需求设计、网络连接、网络设备、设备连接等进行了论述。     

Synthesis and activation of Pt nanoparticles with controlled size for fuel cell electrocatalysts

Well-dispersed Pt nanoparticles with controlled size and narrow size distribution were prepared by polyalcohol reduction of platinum acetylacetonate, using oleylamine as a capping agent. The particle size was varied from 3.5 nm to 11.5 nm by decreasing the amount of oleylamine added in the synthesis. Size selection of the as-prepared particles by solvent fractionation yielded nearly monodispersed Pt particles. The as-prepared particles were loaded on a carbon support by physical deposition, but showed no electrocatalytic activity due to the oleylamine bound to the particle surface. The particles were activated for electrocatalysis after heating the particles in air at 185 °C for 5 h, conditions that gave no particle-sintering and no oxidation. Cyclic voltammetry showed that the particles after the heat treatment in air were electrocatalytically active for methanol oxidation. The smaller 3.5 nm and 4.0 nm Pt particles had a higher intrinsic activity for methanol oxidation, but a lower tolerance to CO poisoning, compared with 6.0 nm, 9.5 nm and 11.5 nm particles. CO-stripping results suggest that CO is more easily oxidized on larger Pt particles.     

高压水射流粉碎原盐

高压水射流粉碎技术是近年发展起来的一项新型粉碎技术。文中介绍了水射流粉碎机理和新研制的后混合靶式水射流粉碎装置 ,并通过原盐粉碎实验证明 ,水射流粉碎具有效率高、工艺简单、产品粒度可调等特点 ,是一项具有良好发展前景的粉碎技术。     

Electrical and optical studies of ZnO:Ga thin films fabricated via the sol–gel technique

The effects of dopant (Ga) concentration, post-heat treatment temperatures, and different heat treatment environments on the morphology, electrical and optical properties of ZnO films were studied. ZnO films doped with Ga are derived from non-alkoxide zinc acetate via the alcoholic route by a sol–gel dip-coating technique. Introduction of Ga, as a dopant, can reduce crystallite size, which is attributed to the increased number of nucleation centers. Grain growth was also observed at high post-heat treatment temperature. It was discovered that different post-heat treatment environments (air or reduced atmosphere) did not change the structure orientation, microstructure shapes and size. It was found that the sheet resistance, R_s could be reduced by an order of magnitude, using post-heat treatment in reduced atmosphere (4%H₂–96%N₂).     

纳米氧化铝的制备及应用

介绍了高科技产品纳米氧化铝的 3大制备方法 :固相法、气相法、液相法的优缺点 ,以及纳米氧化铝的应用与发展前景     

超强吸水树脂的吸水性能研究

对自制的超强吸水树脂的吸收性能进行了研究，分别考察了吸水树脂的粒径，溶液的pH值，几种离子如Na^ ,K^ ,Ca^2 ,Mg^2 等的水溶液对吸水树脂吸收性能的影响。实验结果表明，在pH为6－8，树脂粒径为100mesh-120mesh时，树脂的吸水性能最好，各种离子对吸水树脂吸收性能的影响大小顺序为：Na^ ＜K^ ＜Mg^2 ＜Ca^2 。     

Mechanical and thermal properties of HVOF sprayed Ni based alloys with carbide

The objective of the present study is to develop multi-functioned coating to the components, which are made of copper with electroplated Ni and are widely used for steel making industry. In this paper, we report the mechanical and thermal properties of Ni based superalloys with carbide sprayed by high velocity oxygen fuel (HVOF), and the detailed effects of sprayed material, spraying conditions, and initial powder structure on these properties. It was found that, among commercial Ni self-fluxing alloys (without fusing treatment), coating with a carbon content of 0.58 mass% had the most preferable properties, with a good balance of the hardness, strength, and thermal shock resistance. The thermal shock resistance depended not only on the strength of the coating but also on the volume contraction when tested at high temperatures. For the several developed Ni based superalloys with carbide, Ni20Cr8Mo5Fe–WC and Ni16Cr15Mo3–WC demonstrated the prominent adhesion strength and thermal shock resistance with high Galvanic corrosion resistance through optimized spraying condition. Also, 20 mass% NiCr–Cr₃C₂ coating sprayed by using employed relatively small primary particle succeeded in achieving the multi-superior properties; high adhesion strength, high corrosion resistance and thermal shock resistance.     

高炉鼓风机就地扩容改造方案及经济效益

介绍了利用高炉鼓风机基础实施不易地扩容改造的设计工艺方法，该方法不仅降低了设计、施工、安装费用，而且缩短了施工周期，降低了固定资产投资。     

Recent developments of high-performance NEOMAX magnets

For further improvement in achieving extremely high magnetic properties of Nd- Fe- B sintered magnets, extensive investigation has been done to densify the magnet up to the theoretical value, to increase the volume fraction of the Nd ₂Fe₁₄B matrix phase, and to achieve a high degree of alignment. By controlling chemical composition and the amount of constituent phases,improving particle size distribution, and adopting the isostatic pressing method to get better alignment of fine particles, we have succeeded in obtaining a high-performance magnet having residual flux density (B_r) of 1.495 T (14.95 kG), maximum energy product [(BH)_max] of 431 kj/m³ (54.2 MGOe), and intrinsic coercivity (iH_c) of 845 kA/m (10.62 kOe).