Surface designing of polypropylene by critical monitoring of the grafting conditions

The grafting of acrylic acid onto electron beam‐irradiated polypropylene was carried out using preirradiation method. The stability of peroxy radicals was investigated by electron spin resonance. It was found that the decay of peroxy radicals is much faster at 70°C than at 40°C and ambient temperature. The grafting has been observed to be strongly dependent on the monomer dilution in the reaction medium. The grafting was ascertained by attenuated total reflectance (ATR). The distribution of grafts across the samples was monitored by infrared microscopy. It was found that the graft management is considerably influenced by composition of the grafting medium. The grafting involving pure monomer leads to the surface enrichment with the polyacrylic acid chains. The samples grafted in pure monomer led to much lower contact angles as compared to the diluted monomer solution. The swelling of the grafted samples also showed a trend that was governed by the graft management. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 546–553, 2006     

飞轮快速静平衡工艺

介绍了一种适应多品种小批量生产类型的飞轮快速静平衡工艺。     

硬粒子对聚合物材料表面的冲击摩擦研究

冲击摩擦为接触面切向与法向冲量之比。用聚合物材料试件与弹簧钢片组成振动测试系统 ,硬粒子以一定入射角冲击试件水平面引起系统振动 ,接触冲量通过振幅反映出来 ,记录初始振幅值而计算出一个冲击过程的冲击摩擦因数。结果表明 ,当入射角α在 2 5°-60°变化时 ,冲击摩擦因数f从 0 .5降至 0 .2左右。文章同时分析讨论了摩擦对聚合物表面接触强度的影响。     

Instability due to Viscosity Stratification Downstream of a Centerline Injector

A common injector geometry upstream of a static mixer is the centerline injector. A flow instability can arise due to viscosity differences between the injected core‐flow and the outer co‐flow. This instability can adversely affect the effectiveness of the mixing operation. An experimental investigation of miscible viscosity‐stratified flow in a circular geometry was performed using Laser Induced Fluorescence (LIF) and Particle Image Velocimetry (PIV). The experimental results for the stable region agree with the analytical results. The unstable region exhibits different modes depending on the viscosity ratio, volume flux ratio, and Reynolds number. The modes include wavy core‐flow with fissures and wavy core‐flow with core breakup. The time‐averaged experiment velocity profiles for the unstable core indicate a broadening of the jet at the centerline, which is consistent with the LIF visualization.     

工艺空气压缩机组开车过程的思考

通过汽轮机组调速系统伺服马达不复位、主汽门不动作，反推出电磁阀控制线路接线错误，用人为短路压力开关等手段判断出组合油脱扣器活塞卡涩是造成现场延误开车的根本原因，提出完善大机组开车工作票制度、提高人员素质等措施。     

转换波延迟时静校正

为了克服传统转换波静校正方法应用效果不佳的缺点,本文介绍一种转换波延迟时静校正方法,此法根据转换波勘探时垂直分量记录的纵波近地表模型及水平分量记录的初至时与纵波分量的初至时之差,求取转换波延迟时,并根据转换波延迟时建立横波的近地表模型,从而求取接收点的横波静校正量。文中给出了转换波延迟时静校正量的计算公式,并用实际地震数据进行了检验。结果表明此法应用效果较好,可以推广应用。目前该静校正方法已经集成到KLSeis采集软件中。     

共聚物水凝胶的合成及其溶胀性能研究

以过氧化二苯甲酰(BPO)为引发剂，合成了N-乙烯基吡咯烷酮(NVP)-甲基丙烯酸肛羟乙酯(HEMA)-甲基丙烯酸丁酯(BMA)共聚物水凝胶，可作为软性角膜接触镜材料。探讨了不同比例的NVP、HEMA、BMA对材料溶胀性能的影响。     

Characterisation of plasticity-induced closure--crack flank contact force versus plastic enclave

This paper presents some results from a totally new and powerful fusion between automated, digital photoelastic techniques and mathematical analysis of a crack experiencing closure. In essence, real-time photoelastic stress field data is acquired and fitted to a Muskhelishvili complex potential model of a loaded crack experiencing closure. The fit entails optimisation of multiple variables via a memetic algorithm, which combines a genetic algorithm and a local search. From observations made in this work, it is proposed that the plastic enclave around a crack tip will shield the crack from the full influence of the applied stress field. Furthermore, the effects of this ‘back stress’ are overcome by the applied tensile load in a way that, often, cannot be readily correlated with crack contact length, wake contact force, or with compliance.     

钢筋混凝土筒仓动态压力的计算

讨论钢筋混凝土筒仓在卸料时由于整体流动引起仓壁的动态压力，考虑了筒仓的流动压力及侧压力系数随仓体深度变化这一实际情况，得出仓壁动态压力的计算公式。计算结果与筒仓试验测得的动态压力数值相接近。     

精馏塔静态仿真：Ⅰ.静动态混合数学模型的应用

本文为了克服精馏塔静态仿真不易收敛和初值难以给定等难题，巧妙地利用隐含数值积分方法的特点，将稳态与动态数学模型耦合起来，用以求解高难度的非理想精馏塔静态仿真问题。所得静动态混俣模型大大提高了精馏塔静态仿真的鲁棒性，对于高度非理想精馏塔的仿真尤为有效。通过对某丙烯腈萃取精馏塔的静态仿真，充分证明了这种混合模型化方法的可行性。