温度应力、自收缩对高性能混凝土早期开裂的影响

根据高性混凝土的水化特性、物理力学特性及自收缩特性，分析了高性能混凝土早期开裂机理和影响早期开裂的主要因素．并结合工程实例，借助混凝土温度和应力有限元仿真计算方法分析研究了表面适度保温和水管冷却技术在高性能混凝土温控防裂中的应用效果．研究结果表明，表面适度保温与水管冷却相结合能有效降低混凝土的内外温差，减小混凝土早期表面拉应力与后期内部拉应力，防裂效果明显，对类似的工程具有借鉴作用．     

The impact of roasting on the ochratoxin A content of coffee

Roasting coffee led to a drop in the ochratoxin A (OTA) concentration, as measured by the reference method, especially for dark type roasts. The way the beverage was prepared also affected the OTA content, which could paradoxically be higher than that of the initial roasted coffee. Assays on the thermal stability of pure OTA showed that it ought to be found in larger quantities in roasted coffee. This suggested that OTA was masked by reactions with the substrate during roasting. The absence of OTA in green coffee is therefore the best guarantee of safety.     

Synthesis of unsaturated polyesters of increased solubility in styrene

The present study presents the synthesis of unsaturated polyester resins using only one glycol i.e., ethylene glycol. Polyesters of inorganic solubility in styrene were prepared. Properties of the resins in the noncrosslinked state in the process of crosslinking and after curing were studied. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3143–3150, 2006     

Heterogeneous chain propagation in low-pressure flames

An analysis of papers on hydrogen combustion at low pressures is performed, which refines the contribution of the catalytic reactions on the reactor wall to the gas-phase part of the process. A new model for the heterogeneous loss of active reaction centers was proposed and tested experimentally to explain inconsistencies that occur in some papers. In this model, the diffusion region of chain termination is formed under standard experimental conditions in vacuum oxyhydrogen flames at a reactor gas pressure a thousand times lower than the boundary pressure postulated by the previous models as the pressure below which the diffusion region of chain termination cannot be formed. __________ Translated from Fizika Goreniya i Vzryva, Vol. 42, No. 2, pp. 10–18, March–April, 2006.     

3-D MCM封装技术及其应用

介绍了超大规模集成电路（VLSI）用的3-D MCM封装技术的最新发展，重点介绍了3-D MCM封装垂直互连工艺，分析了3-D MCM封装技术的硅效率、复杂程度、热处理、互连密度、系统功率与速度等问题，并对3-D MCM封装的应用作了简要说明。     

Heat resistance of Escherichia coli O157:H7 in cook‐in‐bag ground beef as affected by pH and acidulant†

Summary The heat resistance of a four‐strain mixture of Escherichia coli O157:H7 was tested. The temperature range was 55–62.5 °C and the substrate was beef at pH 4.5 or 5.5, adjusted with either acetic or lactic acid. Inoculated meat, packaged in bags, was completely immersed in a circulating water bath and cooked to an internal temperature of 55, 58, 60, or 62.5 °C in 1 h, and then held for pre‐determined lengths of time. The surviving cell population was enumerated by spiral plating meat samples on tryptic soy agar overlaid with Sorbitol MacConkey agar. Regardless of the acidulant used to modify the pH, the D ‐values at all temperatures were significantly lower (P < 0.05) in ground beef at pH 4.5 as compared with the beef at pH 5.5. At the same pH levels, acetic acid rendered E. coli O157:H7 more sensitive to the lethal effect of heat. The analysis of covariance showed evidence of a significant acidulant and pH interaction on the slopes of the survivor curves at 55 °C. Based on the thermal‐death–time values, contaminated ground beef (pH 5.5/lactic acid) should be heated to an internal temperature of 55 °C for at least 116.3 min and beef (pH 4.5/acetic acid) for 64.8 min to achieve a 4‐log reduction of the pathogen. The heating time at 62.5 °C, to achieve the same level of reduction, was 4.4 and 2.6 min, respectively. Thermal‐death–time values from this study will assist the retail food processors in designing acceptance limits on critical control points that ensure safety of beef originally contaminated with E. coli O157:H7.     

Analysis of the Datagram Congestion Control Protocol’s connection management procedures using the sweep-line method

State space explosion is a key problem in the analysis of finite state systems. The sweep-line method is a state exploration method which uses a notion of progress to allow states to be deleted from memory when they are no longer required. This reduces the peak number of states that need to be stored, while still exploring the full state space. The technique shows promise but has never achieved reductions greater than about a factor of 10 in the number of states stored in memory for industrially relevant examples. This paper discusses sweep-line analysis of the connection management procedures of a new Internet standard, the Datagram Congestion Control Protocol (DCCP). As the intuitive approaches to sweep-line analysis are not effective, we introduce new variables to track progress. This creates further state explosion. However, when used with the sweep-line, the peak number of states is reduced by over two orders of magnitude compared with the original. Importantly, this allows DCCP to be analysed for larger parameter values. Somsak Vanit-Anunchai was partially supported by an Australian Research Council Discovery Grant (DP0559927) and Suranaree University of Technology. Guy Edward Gallasch was supported by an Australian Research Council Discovery Grant (DP0559927).     

The Effect of Structural Defects on the Thermal Conductivity of ZnS, ZnSe, and CdTe Polycrystals

ZnS, ZnSe, and CdTe polycrystals are experimentally investigated. Mechanisms are treated which restrict the thermal conductivity in samples prepared by recrystallization pressing and by deposition from the vapor phase and subjected to additional strain. Anomalies are observed on the temperature dependences of the thermal resistance of investigated samples, which are due to the special features of their phonon spectra and to the variation of the contribution made by longitudinal and transverse phonon branches to the heat transfer in the Debye temperature region and higher.     

金属基复合材料的热残余应力力学模型研究进展

金属基复合材料在高温制备的冷却过程中或热处理过程中由于组分间热膨胀系数（CTEs）的差异会产生较大的热残余应力，热残余应力对复合材料的宏观性能有着重要的影响。本文综述了分析金属基复合材料热残余应力的有限元模型和解析模型等理论模型，并指出有待深入研究的问题。     

对一起氮压机燃爆事故的原因分析

SVK8 3S型氮气压缩机是由沈阳鼓风机厂制造、为义马煤气配套的低压氮气压缩机 ,共两套 ,于 2 0 0 0年 1 2月开始调试。为节约工程基建资金 ,取消原设计两台中压氮气压缩机 ,由杭氧产两台3TYS89+2TYS60型氧气透平压缩机临时压送氮气 ,向外供中压氮 ,来取代中压氮气压缩机 ,流程示意图如图 1所示。图 1　氧、氮压机工艺流程配置图1　事故情况2 0 0 0年 1 2月 2 7日中午 1 1∶3 5 ,接总调度室通知 ,要求中午 1 2∶0 0向长输管线供中压氮气。当时 ,一台氮压机试车完毕正在运行 ,一台氧压机试车完毕压氧正在运行 ,将由氧压机临时压送氮气外供…