用攀枝花钛矿和云南钛矿冶炼钛渣工业试验研究

通过磁性测量和X-射线衍射研究了Gd2(Co，Al)17化合物的结构和磁晶各向异性。当x≤4时，样品具有菱方Th2znl7型结构，x=5时，具有六方CaCu5型结构。随着Al浓度增加，晶格常数和单胞体积单调增大，而居里温度和自发磁化强度近似线性地减小；在x≥l时，观察到Co亚点阵的磁晶各向异性变号，室温易磁化方向由易面转变为易轴，且易轴各向异性场和各向异性常数随Al原子浓度增加出现极大值；基于补偿温度(65K)下自由粉末颗粒的磁化曲线，导出了亚点阵间的分子场系数和Gd-co交换耦合常数，结果表明，Al原子对Gd-Co交换耦合作用的影响较小。根据Al原子在Co亚点阵4种晶位的择优占位，分析了磁晶各向异性的演变。     

Synthesis of Ti3SiC2 by spark plasma sintering(SPS)of elemental powders

Ti3SiC2 materials have been fabricated by spark plasma sintering of the elemental powders with the addition of Al.At the heating rate of 80℃/min and under the pressure of 30MPa,the ideal synthesis temperature of Ti3SiC2 is in the range of 1150-1250℃.The addition of Al is in favor of the formation of Ti3SiC2.The synthesized compound has the molecular of Ti3Si0.8Al0.2C2 and lattice parameters of α=0.3069nm,c=1.7670nm.Its grain is plane-shape with a size of about 50μm in the elongated dimension.The prepared material has Vickers hardness of 3.5-5.5GPa(at 1N and 15s) and is as readily machinable as graphite‘s.     

K2O和Na2O对高Al2O3炉渣组元活度和MgO含量的影响

 随着高品位铁矿石消耗的加快,资源逐渐趋于贫化,钢铁企业可利用的铁矿石原料逐渐向中低品位原料转变,尤其是高铝铁矿,这类原料的使用无疑会增加高炉渣中Al₂O₃质量分数,影响高炉现有的操作制度。Al₂O₃质量分数为15%～17%的高炉渣,由于Al₂O₃含量高而使高炉渣的冶金性能变差,为了保证高炉渣的冶金性能,必须在其中添加8%左右的MgO。然而,Al₂O₃含量相似的浦项钢铁的高炉渣,其MgO质量分数仅为4%左右,高炉实现了高效、稳定、顺行。因此,从高炉CaO-SiO₂-Al₂O₃-MgO四元渣系的物理化学机理出发,研究了K₂O、Na₂O对高炉渣四元渣系CaO-SiO₂-Al₂O₃-MgO中各组元活度的影响;研究了“渣-气”平衡条件下渣中碱金属氧化物和气体中碱金属的关系;计算了K₂O、Na₂O和MgO对黏度的影响。结果显示,在考虑高炉渣CaO-SiO₂-Al₂O₃-MgO中各组元活度、碱金属在渣-气间的分布和炉渣黏度的情况下,当碱金属氧化物K₂O和Na₂O存在时,可以适当减小MgO含量,并可以保证高炉渣各组元活度及炉渣黏度基本不变。这不仅有助于减少高炉原料中添加含镁熔剂、提高原料品位、高效排碱、降低碱危害、减少碳排放、延长高炉寿命及降低成本,还能促进钢铁企业实现节能减排的目标。     

Microstructure and mechanical properties of high strength as—cast Ti—15—3 alloy

The effects of heat treatment and solidification cooling rate on the microstructure and mechanical properties of as-cast Ti-15-3 alloy prepared by induction skull melting method were investigated.Results show that the microstructure of as-cast Ti-15-3 alloy changes from the features of simplified and larger size of beta grains to finer grain size with increasing solidification cooling rate.After solution treatment and different ageing treatment,alpha phase precipitates in grains interior as well as in grain boundaries.Due to the modification of the precipitate phase,the tensile stength and elongation of the alloy are improved simultaneously.A good combination of the values of 1.406GPa of σb and 4.5% of δ was obtained,which will be satisfied the use of this kind of alloy in critical areas.     

反求工程的产品几何建模技术研究

分析了目前在反求工程产品几何建模中广泛应用的曲面模型的局限性，指出反求工程为实现创新功能必须采用产品特征模型，提出了基于实体造型的特征建模方法。这种方法可以避免曲面模型的缺陷，拓宽反求工程的应用范围，是实现三维重构的新方法。探讨了有关的理论和关键技术。     

Stress relaxation behavior of Ti-6Al-4V alloy

1　INTRODUCTIONTi 6Al 4VisoneofthemostimportantTial loys[1,2 ] .Butthisalloyhasbadformabilityforitshighelasticresilience .Therefore ,hotsizingisimpor tant[36 ] .Asthebaseofhotsizing ,thestudyofstressrelaxationhasimportanttheoreticalvalueandpracticalsignificance .Ontheotherhand ,Ti 6Al 4Visusedasfastenermaterialssometimes .Whenthefastenersworkatthetemperaturehigherthanroomtemperature ,stressrelaxationmayresultsinacci dents .Sohowtopreventthestressrelaxationisveryimportant[7] .Uptonow ,…     

Thermal stability behaviors of Cr(N,O)/CrN double-layered coatings by TGA/DTA analysis

In this study, Cr(N,O)/CrN double-layered coatings were synthesized using the cathodic arc deposition (CAD) process. CrN film was first deposited onto a substrate as an interlayer to ensure better adhesion, and Cr(N,O) film was subsequently deposited on top of the CrN layer as the surface layer. Variation in the Cr(N,O) coating composition was achieved through changing the O₂/N₂ flow ratio during the last stage of processing. Phase structure, chemical composition, and morphology of the resulting coatings were analyzed and observed using the X-ray diffractometer, Auger electron spectrometer and SEM. In addition, oxidation behavior of the coatings was investigated using TGA/DTA methods. The tests were carried out by increasing temperature up to 1000 °C in ambient air. With the introduction of oxygen gas during the CAD process, a superficial layer was produced in the Cr(N,O) constituent containing CrN and Cr₂O₃ phases. The formation of the oxide phase attributed to the reaction of chromium and oxygen was more favorable than that of chromium and nitrogen. The results also showed that Cr(N,O)/CrN double-layered coatings exhibited superior oxidation resistance at elevated temperature than that of CrN single-layer coated specimen (870 °C vs. 750 °C).     

离心成型法制备Al2O3/Ni功能梯度材料及性能表征

用离心成型法制备了Al2O3/Ni功能梯度材料,并研究了料浆调制工艺、制备参数和梯度材料的力学性能.结果表明,良好的料浆的最佳流动性配比为粘结剂(聚乙二醇)含量为2 mass%、固相含量为63 vol.%、球磨时间为36 h.经离心成型-真空烧结(1400℃,2 h)可获得致密、组元宏观连续过渡的Al2O3/Ni梯度材料.该复合材料孔隙率低,力学性能好,抗弯强度可达321 MPa.     

燃烧合成Ni_3Al组织结构转变动力学过程分析

采用端部淬火熄火方法分析了自蔓延合成Ｎｉ－２５ａｔ．－％Ａｌ合金中的组织结构转变过程．研究表明：合金中的合成反应是从铝熔化后形成富铝合金溶液及富铝化合物处开始，然后再通过一系列中间过渡反应逐渐向γ′Ｎｉ_３Ａｌ产物相转化，其中液态反应物形成及其流动铺展，是形成快速放热反应及其自发扩展燃烧波的主要机制．     

气-电纺PHB引导组织再生膜的仿生矿化研究

实验将PHB通过气流-高压静电纺丝制成无纺膜，利用扫描电镜（SEM）、X射线衍射（XRD）对其形态和结构进行表征。在体外研究中，分别将无纺膜样本浸入37℃1．5倍仿生体液（SBF）中3、7、14、28d后对其表面形态和结构进行表征。结果表明，气电纺PHB无纺膜由超细纤维交织而成，纤维之间有多孔形成；通过气流一静电纺丝之后，PHB的结晶度及晶体的有序度降低；PHB膜在SBF中浸泡3天之后就有矿化结晶在纤维的表面形成，随着浸泡时间的增长，矿化结晶的数目增加，结晶度也随之增高，XRD及FTIR表明形成的结晶为含有碳酸根的磷灰石晶体。