Influence of additives on electrodeposition of bright Zn-Ni alloy on mild steel from acid sulphate bath

The influence of a condensation product (CP) of veratraldehyde (VRTD) and p-amino benzoic acid (PABA) on Zn-Ni alloy electrodeposited onto mild steel was studied in acidic sulphate solutions. Ethylenediaminetetraaceticacid (EDTA) and cetyltrimethylammoniumbromide (CTAB) were used as complexing and wetting agents, respectively. The effect of bath constituents, pH, current density and temperature on nature of deposit were studied through Hull cell experiments. The bath constituents and operating parameters were optimized. Deposit properties and corrosion resistance were discussed. Throwing power, current efficiency and polarization studies were carried out. SEM photomicrographs of the deposit obtained from optimum bath revealed fine-grained deposit of the alloy in the presence of condensation product and hence modified the morphology of zinc-nickel alloy deposit. IR spectrum of the scrapped deposit showed inclusion of addition agent.     

含钡合金的生产及其对钢液脱氧行为的研究

介绍了含钡合金的生产状况。在MoSi2炉上对钢管钢进行了含钡合金脱氧行为的研究，然后在150tLF／VD精炼设备上进行了使用含钡合金的工业试验。研究中主要选取SiAlBa、SiCaBa、SiAlBaCa、SiAlBaCaSr及用于钙处理的SiCa包芯线，并选用Al和FeSiAl作为对比脱氧剂，分别考察了实验室条件下和实际生产过程中，采用钡系合金对钢液脱氧的全氧含量，脱氧产物的分布、尺寸和形貌，探讨了钡系合金脱氧和对夹杂物的变质作用的机理。     

不同磁场作用对AZ31镁合金的凝固组织的影响

镁合金是具有优越性能的金属材料,镁合金的加工是目前国内外正在深入进行研究的新课题.实验发现在镁合金的凝固过程中施加低频或静态磁场都能细化晶粒,但静磁场得到的细化效果要优于低频交流磁场,同时随磁感应强度的增加,静磁场细化晶粒的效果明显提高;在静磁场条件下晶界共晶体组织的厚度明显减小,同时在晶内出现了大量细小块状化合物,这有利于改善镁合金的综合性能.     

自蔓延高温合成TiNi多孔体合金

为了开发新型的生体材料，本文对自蔓延高温合成TiNi多孔体合金——人造骨材料进行了研究。以单质钛粉和镍粉作原料，在氩气保护条件下，采用预热点燃模式和热爆模式制得了不同形态的多孔TiNi形状记忆合金。采用SEM和XRD分析了样品的孔洞特征和相组成，测试了其力学性能，并研究了合成条件参数与样品表面形貌和孔隙状态之间的关系。结果表明，用SHS法制备TiNi多孔体合金是可行的。     

Quantitative assessment of preferential fatigue initiation sites in a multi‐phase aluminium alloy

Complex multi‐phase Al–Sn–Si alloys are commonly employed in the manufacture of small automotive plain bearings. The fundamental fatigue initiation behaviour of this class of alloys is currently not well understood. A range of analytical techniques were applied to investigate preferential initiation site location and to attempt to identify critical microstructural features. It was apparent from experimental studies that points of fatigue crack initiation are associated with the Si secondary phase. Using tessellation approaches and subsequently both adaptive numerical modelling and micro‐scale finite element modelling allowed the identification of features affecting the probability that a given Si phase would initiate a fatigue crack.     

Structure of rapidly solidified aluminum alloys

This paper is a summary of an extensive research program carried out by the authors on the structure of rapidly solidified aluminum alloys; and a comparison with the work of others also involved in this field. The paper discusses the changes in the dendritic and non-dendritic structure of the matrix at cooling rates from 10^–3 to 10¹⁰ K/s and discusses the hetergeneity of the structure caused by interdendritic-segretion during solidification.     

镁基储氢材料的研究进展

本文回顾和总结了近几十年来，特别是近十年来镁基储氢材料的发展情况，重点综述了机械合金化Mg-Ni2合金体系的研究情况及其近期的进展，从储氢材料成份及配比，制造工艺改进以及材料的组织结构对材料性能的影响等各方面进行一定的分析和归纳，对储氢材料研究中出现的问题以及今后的发展方向都作了探讨。     

SiGe:GaP合金的微观结构和温差电特性

经高温热处理后的 SiGe∶GaP 半导体温差电材料,其微观结构由具有富 Si 相特征变化成为具有富 Ge 相特征,温差电优值也得到了提高。实验还表明,材料晶格热导率的降低与富 Si 相的消失和富 Ge相的出现有关。然而,塞贝克系数和电导率的显著变化却与微观结构中富 Si 相和富 Ge 相的变化基本无关。通过对材料微观结构和温差电特性比较发现,具有富 Ge 相特征的微观结构对应于较大的温差电优值。     

铝锂合金力学性能的各向异性

针对当前困扰铝锂合金实际应用的各向异性问题，概述关于铝锂合金中各向异性的表现规律，产生机理及对于降低各向异性所采用的方法等方面的研究现状和进展，对铝锂合金各向异性表现与微观组织结构的关系以及目前克服各向异性所采用方法的局限性进行分析。就此提出，若彻底解决这一问题则必须采用更先进的合金化方法及热加工工艺，研制新一代铝锂合金的观点和研究方向。