Properties of Quaternary Alloy Magnetic Semiconductor (InGaMn)As Grown on InP

We have studied properties of quaternary alloy magnetic semiconductor (InGaMn)As grown on InP substrates by low-temperature molecular-beam epitaxy (LT-MBE). A large MCD peak whose intensity is larger than 500 mdeg for (InGaMn)As was observed. This peak intensity was about three times larger than that of typical (GaMn)As films. Relatively high Curie temperature of 83 K of [(In_0.53Ga_0.47)_0.88Mn_0.12]As was observed by Hall measurements. The carrier concentration of [(In_0.53Ga_0.47)_0.88Mn_0.12]As was estimated to be more than 1.0 × 10²¹ cm^–3 by using the Curie–Weiss fitting of the Hall coefficient R _H, indicating that more than 40% of Mn atoms are activated. This means that (InGaMn)As has a higher activation ratio of Mn as acceptors than (GaMn)As.     

Effect of heat treatments on tensile properties and microstructures of wrought Mg−Zn−Zr-RE alloys

The effect of heat treatments on the tensile properties and microstructures of wrought Mg–Zn–Zr-Rare earth alloys MB25 and MB26 have been studied in this paper. It was shown that the homogenization of the cast ingots decreased the strength of the extruded bars because some grain boundary phases were dissolved during the process of this treatment, while the ageing treatment of the extruded bars increased the strength due to the dispersive precipitation of MgZn₂ phase. The quenching + ageing treatments of the extruded bars decreases the strength and plasticity because of the growing up of the grains.Abbreviations ED electron diffraction - GB grain boundary - RE rare earth - TEM transmission electron microscope     

含钡合金在钢液中的脱氧行为研究

在MoSi2炉上采用MgO质坩蜗对钢管进行了含钡合金脱氧行为的研究。实验中钡系合金主要选取SiAUBa、SiCaBa、SiAlBaCa、SiAlBeCaSr及用于钙处理的SiCa包芯线，选用Al作为对比脱氧剂，考察了钡系合金脱氧的全氧含量，脱氧产物的分布、尺寸和形貌，探讨了钡系合金脱氧和对夹杂物变性作用的机理。     

高能超声处理对锡锑包晶合金凝固组织的影响

在锡锑包晶合金的凝固过程中导入高能超声，不仅显著细化α相和β相晶粒组织，同时使具有立方晶体特征的β相组织有明显的球化趋势，消除了密度偏析，分析了高能超声细化凝固组织的机理。     

SiCp/2024复合材料的氢脆敏感性研究

在浸泡、阴极极化、阴极极化同时迭加拉伸变形、添加As₂O₃毒化剂等常见致氢条件下,通过慢应变速率拉伸试验研究了SiC_p/2024复合材料的力学性能,考察了断口形貌.测定了该材料在按几种常用充氢条件充氢后的氢含量.发现虽然强烈阴极极化使材料力学性能下降,但其原因在于阴极极化引起的碱性腐蚀,与氢脆无关.获得了不同于前人研究的新结论:在本文试验条件下SiC_p/2024材料不发生氢脆,也不发生不可逆氢损伤,其原因与该材料难以充入氢有关.     

TiAl＋Sb合金的热稳定性的研究

研究了退火处理对Ｔｉ－３４ｗｔ．％Ａｌ－０．５ｗｔ．％Ｓｂ合金的室温抗弯性能，显微组织，相组成和断口形貌的影响。发现，低于１０００℃退火处理，ＴｉＡｌ＋Ｓｂ合金的显微组织没有变化，其力学性能仍然保持较高的值。此合金成分适应高温使用条件。     

铜镍锰钴应变电阻合金的研究

为解决我国箔式应变计引进生产线用箔材国产化的问题，本所自行设计研制了一种新型的温度自补偿铜镍锰钴合金。该合金具有良好的性能复现性和工艺稳定性，制片后的各项性能十分优异，特别是其平均热输出系数Ｃｔ和对试件材料的适应性明显优于进口箔，是制造高精度箔式应变计的理想材料。     

过共晶Al－Si合金共生区激光表面处理

用２ｋＷ连续ＣＯ２激光对过共晶Ａｌ－１８Ｓｉ合金以不同能量密度和扫描速度进行快速熔凝处理。用扫描电镜、电子微区分析仪分析了微观结构。从计算机对Ａｌ－Ｓｉ合金ｆ－ｎｆ系统的非平衡理论计算所得的共生区及实验结果的分析可见，当能量密度和扫描速度决定的凝固条件处于共生区中部时，过共晶Ａｌ－Ｓｉ合金激光表面处理可以得到共晶间距低于２００ｎｍ的完全共晶结构。     

NiTi形状记忆合金基本驱动特性

研究了预应变ＮｉＴｉ形状记忆合金的基本驱动特性，结果表明，加热和冷却过程回复力存在滞后行为；卸载过程中应力与应变具有与加热、冷却过程相关的非线性关系；卸尖力随卸载应变速率增加而降低，此外研究了预应变ＮｉＴｉ合金丝产生回复力后对外应力的响应行为。     

变形温度和变形程度对Ti－31合金性能和组织的影响

通过高温和室温拉伸试验，研究了变形温度和变形程度对Ｔｉ－３１合金板材性能和组织的影响。结果表明，合金在７５０～８５０℃的温度下变形５％～２０％空冷后，其室温机械性能均能达到材料的技术指标要求。并发现了材料在９００℃的临界变形区。