马来酸酐接枝聚丙烯的进展

马来酸酐接枝聚丙烯是拓宽聚丙烯应用领域的重要手段之一,本文综述了马来酸酐接枝聚丙烯的接枝方法和原理,接枝物的性能以及接枝物在聚丙烯合金和共混物、复合材料、粘合剂和涂料领域的广泛应用。     

基于形状记忆合金的TMD半主动控制

针对建筑结构在随机荷载或风荷载作用下可能发生的频率不确定问题,特别是结构自振频率会随振幅的大小而发生漂移的非线性振动问题,提出性能可靠、构造简单的形状记忆合金SMA-TMD自适应半主动控制系统.从理论上探讨形状记忆合金在变刚度TMD控制装置中的应用,并进行相应的参数设计.同时,在研究随机荷载作用下TMD系统动力特性的基础上,结合短时傅里叶变换(STFT)设计出该系统的自适应半主动控制算法.算例表明,SMA-TMD自适应控制系统能较好地识别结构系统的时频特性,并进行有效的控制,具有性能可靠和自适应能力强等特点.该自适应控制系统较传统的TMD被动控制减震效果更好,鲁棒性更强.     

Corner forming of AZ61A magnesium alloy tube within warm hydroforming

The corners with small radii on cross sections are crucial for forming hydroformed components with polygonal sections.In this paper,warm hydroforming experiments of AZ61A magnesium alloy tubes were carried out to study the forming regularity of round corners by using a demonstration part with square sections.Effects of temperature on radius forming,thinning ratio distribution and microstructure were revealed and a component with relative outer corner radius of 3.0 was obtained by warm hydroforming at 240℃.The minimum thickness of the formed square section was located in the transition position between the corner and the straight wall.The thinning ratio of the round corner increased with the increase of forming temperature.Formability of the magnesium tube was improved by raising temperature under the effect of dynamic recrystallization at 240℃.     

预化学镀石英光纤表面电镀镍层的研究

采用电镀法在石英光纤表面化学镀Ni—P涂层上续镀厚镍,重点考察了硫酸镍质量浓度、十二烷基硫酸钠质量浓度和电流密度对镍沉积速率和镀层质量的影响并确定了其最适宜值。将质量浓度为1．5g·L^-1的稀土氧化镧（La2O3）添加入普通瓦特镀液中考察其对电镀效果的影响。用扫描电镜和体视显微镜对镀层的表面形貌进行了表征和分析。结果表明,添加稀土La2O3细化了金属晶粒和提高了镀层致密程度,镀层样品（厚度约为800μm）具有高硬度、强附着力、低电阻、高密度和良好的可焊性等性能。     

Computation of concentrations of characteristic atoms of alloys in BCC structure

In this paper,taking Nb-Mo alloy system as an example,the equations of concentration of characteristic atoms of alloys in BCC structure were obtained on the basis of the idea of systematic science of alloys and the number of coordination atoms.The concentrations of characteristic atoms in B2-NbMo type ordered alloys were calculated as functions of ordering degree(s) and composition xMo.When s=smax,the concentrations of characteristic atoms of stoichiometric B2-NbMo intermetallic compound are equal to that o...     

铝合金中锌、铁的快速测定--原子吸收分光光度法

样品以盐酸溶解，加入过氧化氢助溶，蒸至近干．加入1 1盐酸提取，移入100mL容量瓶中，分取部分溶液于50mL容量瓶中，调整盐酸酸度为5％，用水稀至刻度，摇匀后，以空气-乙炔火焰水相直接测定锌和铁。为了消除大量基体元素的影响，在标准系列中加入相当量的铝。此方法快捷、简便，亦可用于锰、镁、铜、铅、镍的测定。     

钯－银合金膜分离氢气的研究

采用厚为５０μｍ的Ｐｄ／Ａｇ（２３）合金膜进行了氢气渗透系数的测定和Ｈ＿２／Ｎ＿２混和气分离的研究，得出温度、压力、膜厚、进料气流量、膜的预处理和再活化及膜表面中毒等因素对氢气渗透的影响。分离Ｈ＿２／Ｎ＿２混和气可获得高纯氢气。     

CJ91胶粘剂在螺旋振动光整机中的应用

螺旋振动光整机槽内壁的橡皮保护层由于老化及磨损等原因出现裂口甚至脱落现象，严重影响设备的使用寿命和闸把壳体的外观质量。通过分析和试验筛选出螺旋振动光整机的理想胶粘荆——CJ91胶粘剂并介绍了粘接修补工艺。     

Electrochemical and microstructural characterization of cyclic redox behaviour of SOFC anodes

The oxidation of Ni to NiO in solid oxide fuel cell (SOFC) anode will result in large bulk volume change, which may change the interfaces of the two phases in the anode cermet and thus may cause significant performance degradation. The reduction and oxidation (redox) of the Ni/YSZ cermet were studied at 800 ℃. Anodic polarization measurements were performed before and after redox cycles. The anode current density at an overpotential of 100 mV kept decreasing during the whole redox treatment. It decreased from 19.11 to 7.95 mA·cm-2 after two redox cycles. Anode supported unit cell was assembled for cell's discharge measurements. Cell performance declined after each redox cycle. The maximum power density decreased from 126.28 to 40.32 mW·cm-2 . The microstructural changes after redox cycling were recorded using scanning electron microscopy (SEM). The results reveal that after re-oxidation, the Ni gets coarse and has a higher porosity; the nickel network structure turns to be desultory.