频域吸收边界条件的构造理论

在频域中推导了适用于差分类数值方法的吸收边界条件的构造方法，并通过选取不同参数导出了几种现有的吸收边界条件。在计算了一般形式的吸收边界条件的反射系数之后，提出了一种简单实用的自适应吸收边界条件。     

高强度钢的Zn—Ti合金新镀层

本文研究了一种Ｚｎ－Ｔｉ合金新镀层，经盐水浸泡、中性盐雾和大气暴露试验结果试验，其耐蚀明显超过镀Ｚｎ层，并与镀Ｃｄ层相近，用缺口持久拉伸试验检验氢脆性，拉伸持续时间超过２００ｈ，达到原航空部部颁标准（ＨＢ５０６７－８５），该镀层适用于高强度钢防护。     

Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

Effects of Substrate Temperatures on the Structure and UV-shielding Properties of TiO_2-CeO_2 Films Deposited on Glass by Radio-frequency Magnetron Sputtering

1Introduction Theultravioletrays(UV)insunlight(-4%)cantransmitintoroomthroughcommonfloatglass,theUVcanmakethematerialsintheroom,eg,paper,furni ture,textilefabricandplastics,becoloredanddeterio rated.ShieldingfromUVirradiationisofinterestinmanyfields.Formu…     

Asbestos replacement aspects: Modification of the fibre-matrix interphase in lonomer based composites

Asbestos fibres, of the chrysotile variety, and chopped carbon fibres were pretreated by an in-situ polycondensation technique eventually resulting in a polyamide coating on the fibre surface. Ionomer based composites containing either carbon or asbestos fibres in random in plane fibre orientation were prepared, and the influence of this coating process on the tensile properties was investigated. It was found that for the asbestos-filled composites the presence of the nylon 6,6 interlayer improves the tensile performance, especially at moderate polyamide depositions. This is not the case with the pretreated carbon-filled composites for which carbon fibres with higher polyamide contents are preferred. Combinations of the treated asbestos fibres with carbon and/or aramid fibres may be used to reduce the asbestos content in asbestos-only based engineering plastics.     

乳胶漆的市场现状和发展前景

对乳胶漆的生产现状，产品结构以及研究开发情况作了简单的综述，并展望了乳胶漆的发展前景。     

压敏显色微胶囊及其涂料的研究进展

综述了无碳复写纸的结构类型和性能、压敏显色微胶囊制备及其微胶囊涂料的最新进展。揭示了微胶囊技术在无碳复写纸应用中的重要作用。     

碳纳米管/ABS树脂基复合材料的力学性能和雷达波吸收性能的研究

采用竖式炉流动法制备的碳纳米管经液相阳极氧化表面处理后增强ABS热塑性工程塑料。复合材料的力学性能研究显示:碳纳米管的加入有效提高了复合材料的拉伸性能,但材料的耐冲击性能下降。当碳纳米管含量为12 wt%时,复合材料的拉伸强度由45.00 MPa提高到69.96 MPa,杨氏模量由0.75 GPa提高到1.93 GPa。对碳纳米管/ABS复合材料的反射系数测定表明:复合材料在一定频率范围内有雷达波吸收性能。     

Improving Thermal Stability of BaMgAl10O17:Eu Phosphor

Heterogeneous precipitation method was used to prepared surface coating on self-made BaMgAl10O17:Eu phosphor. Results illustrate that the coating film can be silicon dioxide in amorphous state with 50 nm in thickness. Photoluminescence results indicate that the coating layer presents an observable improved effect on the enhancement of thermal stability. When baked at 600 ℃ for 1 h, the luminance of coated BAM keeps at 92% higher than that of uncoated BAM by 23%. This protective effect can be attributed to the high compact degree and uniformity of this amorphous SiO2 coating film which is served as a diffusion block layer to inbreak oxygen atom, thus releases the oxidation extent of Eu2 effectively.