Improving Short-Circuit Current Capacity, Resistance, and Breaking Load of OPGW Constructions by Modifying Aluminium Alloy With AlB2

This article presents a method that can be applied to molten AA-6101 alloy to improve electrical properties of the aluminium part of the optical ground wire (OPGW) used in overhead transmission lines to protect phase conductors from lightning strike and to transmit signals and data. AA-6101 alloy in casting of the log as 6 m length and 178 mm diameter for extrusion has been inoculated by AlB₂ to decrease detrimental effects of Cr, Ti, V, and Zr on the conductivity of the material. After inoculation, improved billets were extruded as 9.5 mm diameter feedstock. Required wires drawn from the feedstock according to the construction types of OPGW to be tested were exposed to aging at 175°C, 6 h (T-8). Upon completion of the back-twist and performing-type stranding process, resistance, and short-circuit current capacity and breaking load of the OPGW 88/44 constructions with other metal combinations have been examined and tested to show improvement. Results are summarized in tables and graphically.     

关于通信导航设备电源防雷的探讨

根据通信导航设备在雷击中的损坏现象，提出了电源防雷措施，即实施分级保护，在多雷区配置防雷变压器。简单介绍了级间配合，抑制横向过电压的产生，以及接地阻抗的简单计算和正确选用等，以达到对电源系统的有效防雷保护。     

Investigation into polishing process of CVD diamond films

A new technique used for polishing chemical vapor deposition (CVD) diamond films has been investigated, by which rough polishing of the CVD diamond films can be achieved efficiently. A CVD diamond film is coated with a thin layer of electrically conductive material in advance, and then electro-discharge machining (EDM) is used to machine the coated surface. As a result, peaks on the surface of the diamond film are removed rapidly. During machining, graphitization of diamond enables the EDM process to continue. The single pulse discharge shows that the material of the coated layer evidently affects removal behavior of the CVD diamond films. Compared with the machining of ordinary metal materials, the process of EDM CVD diamond films possesses a quite different characteristic. The removal mechanism of the CVD diamond films is discussed.     

加强民用电管理的技术措施

提出并实施了住宅楼集中计量配电系统，为加强民用电管理提供了技术措施。     

吐丝圈径对大规格高碳盘条组织性能的影响

计算与分析了斯太尔摩冷线上盘条的吐丝圈径、搭接密度及"佳灵"装置横向布风曲线之间的关系,研究了吐丝圈径的大小对大规格82B盘条组织和性能的影响,确定了大规格82B盘条最小吐丝圈径应为980mm.     

浅析6063铝型材表面“铝丝印”的成因与对策

在介绍“铝丝印”概念的基础上，从金属腐蚀学的观点出发，分析了“铝丝印”形成的电化学腐蚀机理，并提出了具体的解决措施。     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

弱电系统中的地线干扰与接地方法

介绍了地线的干扰机理以及减小地线干扰的对策和接地的基本方法.在电子电路中,地线不仅为电路提供一个电位公共参考点,而且也为电流提供一条能够流回源的低阻抗路径.由于地线存在阻抗,当电流流过地线时,会在地线上产生电压差,从而形成地线干扰,严重时将会影响电路的正常工作.减小或消除地线干扰的主要方法是减小地线的阻抗和地线电流.为此,可以针对不同的信号频率及干扰性质,根据系统的结构和功能采用相应的接地方式,将接地、屏蔽及滤波等措施结合使用.     

Thermal stability of reinforced Nb3Sn composite superconductor under cryocooled conditions

Several types of reinforced Nb₃Sn wires have been developed to prevent reduction of superconducting properties by applying a strong electromagnetic force. To fabricate a cryocooled magnet using those reinforced wires, we experimentally measured the minimum quench energy (MQE) under cryocooled conditions of some reinforced Nb₃Sn wires. As a result, it became clear that thermal stability expressed as MQE was controlled by the temperature margin between the temperature of the operating condition and the transition temperature from superconductivity to normal. Using the FEM analysis, it was realized that the cause of the decline in thermal stability for the reinforced wires was the low thermal conductivity of the reinforced materials.