A zirconium-free glaze system for sanitary ceramics with SiO2-CaCO3-TiO2 composite opacifier containing anatase: Effect of interface combination among SiO2, CaCO3 and TiO2

TiO₂ is an ideal substitute to ZrSiO₄ ceramic opacifier, yet it is limited to application because of the undesirable yellowing resulting from rutile formation. Herein, the SiO₂-CaCO₃-TiO₂ composite opacifier (Si-Ca-Ti) was constructed. The glaze used Si-Ca-Ti presents a superior opacification performance than ZrSiO₄ opacified glaze without causing yellowing, showing L*, a*, b* values of 94.81, -0.67 and 3.23. By comparison, the glaze using SiO₂, CaCO₃, and TiO₂ mixture shows lower opacification and yellowish surface with L* and b* values of 92.99 and 5.36. It is revealed that there is a close interface bonding among SiO₂, CaCO₃ and TiO₂ in Si-Ca-Ti, which promotes their combination reaction to generate opacification phase titanite and inhibit rutile formation when sintering, resulting in the white surface and opacification improvement of the glaze. This study proposes a green and efficient strategy to achieve white and highly opacified glaze for sanitary ceramics, exhibiting good application prospect.     

Microstructure and mechanical properties of hot-pressed SiC nanofiber reinforced SiC composites

This study reports on the preparation and mechanical properties of a novel SiC_nf/SiC composite. The single crystal SiC nanofiber(SiC_nf) reinforced SiC ceramic matrix composites (CMC) were successfully fabricated by hot pressing the mixture of β-SiC powders, SiC_nf and Al–B–C powder. The effects of SiC_nf mass fraction as well as the hot-pressing temperature on the microstructure and mechanical properties of SiC_nf/SiC CMC were systematically investigated. The results demonstrated that the 15 wt% SiC_nf/SiC CMC obtained by hot pressing (HP) at 1850 °C with 30 MPa for 60 min possessed the maximum flexural strength and fracture toughness of 678.2 MPa and 8.33 MPa m^1/2, respectively. The nanofibers pull out, nanofibers bridging and cracks deflection were found by scanning electron microscopy, which are believed can strengthen and toughen the SiC_nf/SiC CMC via consuming plenty of the fracture energy. Besides, although the relative density of the prepared SiC_nf/SiC CMC further increased with the sintering temperature rose to 1900 °C, the further coarsend composites grains results in the deterioration of the mechanical properties for the obtained composites compared to 1850 °C.     

Sanitary legislation governing Food Services in Brazil

The Technical Regulation of Good Practices for Brazilian Food Services (Regulamento Técnico de Boas Práticas para Serviços de Alimentação do Brasil) can be complemented by sanitary surveillance agencies at the state, district and municipal levels by tailoring it to location-specific requirements. The purpose of the present study was to survey sanitary legislation governing Brazilian Food Services. During the period from November 2011 to November 2012, a survey was conducted with the sanitary surveillance agencies from the various states, capitals and the Federal District. A previously prepared and tested tool was used for data collection, comprising 10 questions. Only 10 (19.2%) of the sanitary codes had been established prior to RDC Resolution n° 216/2004 and were not complementary. Of the legislation cited as complementary, only the states of Santa Catarina, Rio Grande do Sul and São Paulo and the capital of the state of São Paulo truly presented additional and location-specific aspects. No legislation that was specific to hospital kitchens was found. The majority of participating coordination, including the Evaluation List for Good Practices in Food Services, was also verified; however, it had not been published. In conclusion, a gap in sanitary surveillance services exists, which was caused by the lack of location-specific food service regulations.     

Polymer derived ceramic materials from Si,B and MoSiB filler-loaded perhydropolysilazane precursor for oxidation protection

Silica-based coating systems were developed using polymer derived ceramics (PDCs) technology. Ceramic composites on the base of a SiO₂ and SiNO matrix and homogeneously distributed Mo₅SiB₂, SiB₆, Si and B fillers were manufactured. The coating systems have low porosity and provide a high oxidation resistance up to 100 h at 800 °C and 1100 °C in air. The influence of temperature and atmosphere of pyrolysis on the polymer precursor, the volume fraction of filler materials on the chemical composition of compacts as well as their high-temperature oxidation protection was investigated.     

Structural dependence of microwave dielectric properties of spinel structured Mg2(Ti1-xSnx)O4 solid solutions: Crystal structure refinement,Raman spectra study and complex chemical bond theory

Mg₂(Ti_1-xSn_x)O₄ (x?=?0–1) ceramics were prepared through conventional solid-state method. This paper focused on the dependence of microwave dielectric properties on crystal structural characteristics via crystal structure refinement, Raman spectra study and complex chemical bond theory. XRD spectrums delineated the phase information of a spinel structure, and structural characteristic of these compositions were achieved with the help of Rietveld refinements. Raman spectrums were used to depict the correlations between vibrational phonon modes and dielectric properties. The variation of permittivity is ascribed to the Mg₂(Ti_1-xSn_x)O₄ average bond covalency. The relationship among the B-site octahedral bond energy, tetrahedral bond energy and temperature coefficient are discussed by defining on the change rate of bond energy and the contribution rate of octahedral bond energy. The quality factor is affected by systematic total lattice energy, and the research of XPS patterns illustrated that oxygen vacancies can be effectively restrained in rich oxygen sintering process. Obviously, the microwave dielectric properties of Mg₂(Ti_1-xSn_x)O₄ compounds were obtained (${\epsilon }_r$= 12.18, $Q\times f$?=?170,130?GHz, ${\tau }_f$?=??53.1?ppm/°C, x?=?0.2).     

Effects of Ti,Y, and Hf additions on the thermal properties of ZrB2

Reactive hot pressing was utilized to synthesize and densify four ZrB₂ ceramics with impurity contents low enough to avoid obscuring the effects of dopants on thermal properties. Nominally pure ZrB₂ had a thermal conductivity of 141 ± 3 W/m K at 25 °C. Additions of 3 at% of Ti, Y, or Hf decreased the thermal conductivity by 20 %, 30 %, and 40 %, respectively. The thermal conductivity of (Zr,Hf)B₂ was similar to ZrB₂ synthesized from commercial powders containing the natural abundance of Hf as an impurity. This is the first study to demonstrate that Ti and Y additions decrease the thermal conductivity of ZrB₂ ceramics and report intrinsic values for thermal conductivity and electrical resistivity of ZrB₂ containing transition metal additions. Previous studies were unable to detect these effects because the natural abundance of Hf present masked the effects of these additions.     

A cathode support structure for use in a magnetron oscillator experiment

A low temperature co-fired ceramic (LTCC) material system has been used to develop a protype field emission cathode structure for use in an experimental magnetron oscillator. The structure is designed for used with 30 gated field emission array (GFEA) die electrically connected through silver metal traces and electrical vias. To approximate a cylinder, the cathode structure (48 mm long and 13.7 mm in diameter) is comprised of 10 faceted plates which cover the GFEA dies. Slits in the facet plates allow electron injection. The GFEA die (3 mm × 8 mm) are placed in axial columns of 3 and spaced azimuthally around a cylindrical support structure in a staggered configuration resulting in 10 azimuthal locations. LTCC manufacturing techniques were developed in order to fabricate the newly designed cathode with seven layers wrapped to form the cylinder with electrical traces and vias. Two different cathode wrapping techniques and two different via filling techniques were studied and compared. Two different facet plate manufacturing techniques were studied. Finally, four different support stand configurations for firing the cylindrical structure were also compared with a square post stand having the best circularity and linearity measurements of the fired structure.     

Dielectric,ferroelectric, and energy storage properties in dysprosium doped sodium bismuth titanate ceramics

In this work, Na_0.5(Bi_1-xDy_x)_0.5TiO₃ (0?≤?x?≤?15%) ceramics were prepared via solid state reaction method and were characterized. A stable and pure perovskite phase was revealed by X-ray diffraction analysis for all compositions and a symmetry change from rhombohedral to orthorhombic phase was detected beyond 10% of Dy substitution. The incorporation of Dy³⁺ into Sodium Bismuth Titanate (Na_0.5Bi_0.5TiO₃) matrix allows a substantial decrease of the coercive field, an increase in the resistivity, and leads to a high stability of the dielectric permittivity (??/?_(150?°C) ≤?±?15%) over a wide temperature range. Furthermore, this system was found to exhibit improved energy storage properties at high temperatures with a maximum energy density of 1.2?J/cm³ obtained for 2%Dy composition at 200?°C. The obtained results are very promising for energy storage capacitors operating at high temperatures.     

Preparation and temperature-resistance characteristics of novel dense SiAlCN ceramics

The compact green bodies, prepared via a novel solid-liquid mixing method of precursors, were successfully pyrolyzed to obtain the dense bulk SiAlCN ceramics at 1000 °C. It can be seen from their SEM that they have uniform and dense microstructure, indicating that this method can be used to prepare bulk ceramics. In order to verify that they can be used as sensor heads, their temperature-resistance characteristics and repeatability were tested. The results show that the conductive mechanism belongs to Arrhenius's Tailed-State and Extended-State in the temperature range of 500–650 °C and 650–930 °C, respectively. And it shows that SiAlCN ceramics can be used as the sensor heads for high-temperature sensors.     

Grain size dependence of hardness in nanocrystalline silicon carbide

The response of nanocrystalline silicon carbide (nc-SiC) to nanoindentation is investigated using molecular dynamics (MD) simulation. It is found that the hardness of the nc-SiC decreases with decreasing grain size, showing an inverse Hall-Petch relationship. The behavior is primarily attributed to the reduced number of intact covalent bonds with grain refinement. Dislocation nucleation and growth in nc-SiC are strongly suppressed by the grain boundaries (GBs). In addition to the dislocation region in the grains, the indentation-induced amorphization of nanograins proceeds preferentially from the GBs, leading to grain shrinkage until the grains are fully amorphized. The results provide an improved understanding of the mechanical properties in nc-SiC and other nanostructured covalent materials.