含砷、锑、碳难处理金精矿焙烧氰化提金工艺研究

镇沅含砷、锑、碳难处理金精矿直接氰化金浸出率小于 10 % ,采用常规焙烧 -焙砂氰化提金工艺金浸出率仅达到 73 2 % ,而采用先行除锑 ,再焙烧脱除硫、碳、砷的提金工艺方案 ,金氰化浸出率达到90 4 % ,同时锑可作为锑精矿外售 ,经济效益明显。     

Importance of the choice of the profile model for ap-n junction in the location of deep levels

The energy levels introduced by Pt in silicon have been measured in a non-abruptp ⁺-n junction using constant-capacitance thermal-emission rate measurements and a numerical simulation of high frequency-capacitance. Two levels have been detected with activation energies of:E _c -E _T = 0.22 eV with acceptor character andE _T -E _v = 0.34 eV with donor character. The sample preparation and diffusion of Pt is similar to previous works in which an acceptor levelE _c -E _T = 0.34 eV was found instead of or besides a donorlike levelE _T -E _v = 0.34 eV. Our numerical calculation of the shallow-impurity profile points to the existence of a gradual transition near the metallurgical junction for these samples. We have demonstrated that the well-known model of an abrupt junction is not appropriate for these types of junctions, and could lead to errors in the location attributed to the detected levels. Simulation of the electrical behavior leads to the non-existence of the acceptor levelE _c −E _T = 0.34 eV located in then-side of the junction.     

测井岩性类比解释法及应用

利用理想的地质体积模型和电阻率测井的供电电流流过模型的导电机理,推导出一种不需要含水饱和度参数即能定量计算含水饱和度的方法,即岩性类比解释法。经过初步实践,该方法应用于砂泥岩地层的测井分析,效果良好。     

���������͵�����������ķ�����Ӧ��

本文提供了计算凝析油当量气体体积的方法，并用于凝析气藏的凝析油含量，凝析油和干气地质储量的计算。     

烟用香料配制的气相色谱法质量控制研究

采用气相色谱法对香料房卷烟用料液中的溶剂及水分进行检测,分析测定其中的水分、乙醇、丙二醇、山梨醇等的含量,通过对香料房每批配制料液的抽检,可以跟踪料液配制的准确性,保证卷烟产品质量,该方法操作简单、准确性高、重现性好。     

Rapid thermal chemical vapor deposition of in-situ boron doped polycrystalline SIxGe1-x

In-situ doped polycrystalline Si_xGe_1-x (x = 0.7) alloys were deposited by rapid thermal chemical vapor deposition (RTCVD) using the reactive gases SiH₂Cl₂, GeH₄ and B₂H₆ in a H₂ carrier gas. The depositions were performed at a total pressure of 4.0 Torr and at temperatures 600° C, 650° C and 700° C and different B₂H₆ flow rates. The conditions were chosen to achieve high doping levels in the deposited films. Our results indicate negligible effect of B₂H₆ flow on the deposition rate. The depositions follow an Arrhenius type behavior with an activation energy of 25 kcal/mole. Boron incorporation in the films was found to follow a simple kinetic model with higher boron levels at lower deposition rates and higher B₂H₆ flow rates. As-deposited resistivities as low as 2 mΩ-cm were obtained. Rapid thermal annealing (RTA) in the temperature range 800-1000° C was found to reduce the resistivity only marginally due to the high levels of boron activation achieved during the deposition process. The results indicate that polycrystalline Si_xGe_1-x films can be deposited by RTCVD with resistivities comparable to those reported for in-situ doped polysilicon.     

On collaborative content distribution using multi-message gossip

We study epidemic schemes in the context of collaborative data delivery. In this context, multiple chunks of data reside at different nodes, and the challenge is to simultaneously deliver all chunks to all nodes.     

Characterization of one-step,chromate-free,primer systems using liquid-state Si and C NMR

Coatings derived from organofunctional silanes have been investigated as possible replacements for the chromate-based systems used in the aerospace industry. In this study, organofunctional silanes [bis-(triethoxysilylpropyl)ethane and bis(triethoxysilylpropyl) tetrasulfide] were reacted with commercially available acrylate (ECO-CRYL™ 9790) and epoxy (EPI-REZ™ WD-510) resins, resulting in a one-step, low-VOC, chromate-free primer. Liquid-state ²⁹Si and ¹³C NMR were used to determine structural characteristics of various optimized formulations.     

A Mass Transport Model for Drying Wood under Isothermal Conditions

Mass transport in wood during drying can have different mechanisms at different periods of drying. Depending on the current moisture content (MC) and the structure of the wood, the driving forces for the mass transport are essentially different. Above the fiber saturation point (FSP), the lumens are partially saturated and the transport of liquid (free) water occurs as a consequence of capillary action. On the other hand, below the FSP, bound water within the cell walls is conveyed by diffusion, and water vapor in the lumens moves under influence of pressures gradient. Based on these considerations, a unified model is presented that takes into account the transport of the different moisture phases. Simulation of the drying of a Norway spruce sample at 50°C from about 135 to 7% MC is carried out using the finite element method (FEM). Comparison between the simulated average MC and the experimental observations obtained from X-ray computed tomography (CT) shows reasonable agreement. Possible simplifications in the model are briefly discussed as well as some aspects of the numerical implementation. Finally, the influence of absolute permeability on the average MC is studied.     

新型SiMnCr系高强度粗钢筋材料的研制

针对高强度钢筋的性能要求和钢筋生产的工艺特点 ,设计了一种新型的低碳SiMnCr系高强度钢。测定了该钢种的CCT曲线及其力学性能。在锻造或轧态下 ,可获得以低碳马氏体为主含少量贝氏体、残留奥氏体的复相组织 ,经低温回火 ,可获得高的强度 (σb>12 30MPa)和良好的塑性 (δ5≥ 8% )。