Composition Range of Amorphous Mg-Ni-Y Alloys

Based on the thermodynamic point of view, a method for predication of the composition range of amorphous ter-nary alloys was proposed. The composition range of amorphous ternary alloys is determined by the comparison of the excess free energy of the amorphous alloy and the free energy of competing crystalline states. The free energy is extrapolated from the data of three binary alloys by using Toop‘s model. The method was applied to predict the composition range of amor-phous Mg-Ni-Y alloys. The theoretical results are in good agreement with the available experimental results. It indicates that the present method can be used to predict the composition range for amorphous ternary alloys.     

M8011H16铝合金防盗盖板生产工艺研究

研究了元素含量变化对8011铝合金防盗盖板综合性能的影响，在8011合金中改变Cu、Mn元素含量后可提高防盗盖板的强度，同时研究了烘烤处理后的强度变化问题。本文研究出了8011铝合金防盗盖板新的生产工艺制度。     

基于TiNi合金的超弹性对其相关磨损机制的FEM研究

本文在重点考虑TiNi合金高弹性变形量的前提下，采用等向强化模型，对不锈钢和超弹TiNi合金在法向接触载荷作用下的六种模型进行了有限元(FEM)分析。结果表明：在相同载荷条件下，超弹TiNi合金产生的von Mises弹性应变要高于不锈钢，但其von Mises应力和塑性应变却恰恰相反，在同一载荷下该合金发生塑性变形的区域要小于不锈钢；此外，超弹TiNi合金发生塑性变形要比不锈钢困难，所需的临界载荷值随其最大弹性变形量(屈服点处的应变值)的增加而增加。最后，基于本文的有限元计算结果对超弹TiNi合金的蘑粒磨损和疲劳磨损机制进行了讨论。     

含钡合金的生产及其对钢液脱氧行为的研究

介绍了含钡合金的生产状况。在MoSi2炉上对钢管钢进行了含钡合金脱氧行为的研究，然后在150tLF／VD精炼设备上进行了使用含钡合金的工业试验。研究中主要选取SiAlBa、SiCaBa、SiAlBaCa、SiAlBaCaSr及用于钙处理的SiCa包芯线，并选用Al和FeSiAl作为对比脱氧剂，分别考察了实验室条件下和实际生产过程中，采用钡系合金对钢液脱氧的全氧含量，脱氧产物的分布、尺寸和形貌，探讨了钡系合金脱氧和对夹杂物的变质作用的机理。     

TC9合金基体上Al—Cu—Fe—Cr准晶涂层抗氧化性能的研究

采用低压等离子喷涂的方法在TC9合金基体上制备了Al-Cu-Fe-Cr准晶涂层，涂层经750℃，220h静态氧化实验后，对其进行了微观形貌观察和显微硬度实验，以对比分析涂层的抗氧化性能。结果表明，制得的涂层致密并具有较好的抗氧化性能。     

Crystalline Behavior and Magnetic Properties of Nd60Fe30-x Al10Cox（x = 0,5,10） Bulk Amorphous Alloys

Crystalline behavior and magnetic properties of Nd60Fe30-xAl10Cox( x = 0, 5, 10) bulk amorphous alloys were investigated by differential scanning calorimeter (DSC), X-ray diffraction (XRD) and the vibrating sample magnetometer (VSM). Neither glass transition nor supercooled liquid region before crystallization was observed for the as-cast Nd60Fe30-xAl10Cox ( x = 0,5,10) bulk amorphous alloys. The glass forming ability can be improved significantly by the addition of Co. The as-cast Nd60Fe30-xAl10Cox (x = 0,5,10) alloys show hard magnetic behavior. With the addition of Co content, intrinsic coercivity (iHc) increases while the saturation magnetization(σs) and remanence (σr) decrease. The Curie temperature for the as-cast Nd60Fe30-xAl10Cox alloys increases from 451 K for x =0 to 468 K for x = 10. Some pre-cipitation of crystalline phases does not affect the hard magnetic properties of Nd60Fe30-xAl10Cox(x = 0,5,10) alloys, while the hard magnetic behavior disappears quickly after the alloys being completely crystallized.     

转炉合金最小成本控制模型

介绍了基于合金最小成本的转炉炼钢钢水成分调整模型工应用于宝钢炼钢在线生产控制的情况。模型给出了在满足目标成分等工艺要求下，成本最小的合金投入组合及合金投入量；计算了合金加入钢包后引起钢水温度、重量等的变化，为降低生产成本（合金投入），提高出钢成分控制精度提供了有效的途径。     

W-Ni-Cu高比重合金注射成形烧结收缩及性能的研究

研究了W-Ni-Cu高比重合金注射成形工艺过程收缩率和性能。比较了模具尺寸、注射坯尺寸、烧结坯尺寸，及烧结阶段各方向收缩率的关系，发现实际收缩与理论预测收缩率较为一致，但在厚度方向存在与其他方向收缩不一致的情形，这与由重力作用产生的塑料流动有关；还探讨了烧结坯密度与烧结条件的关系，测定了烧结坯的力学性能及断口形貌、金相组织，烧结坯在1400℃，90min烧结达到了99％的相对密度，断裂强度600MPa以上。