中铝河南分公司矿山在土地复垦中的有益探索

分析了铝土矿露天开采和土地、环境之间的利害关系，并对矿山公司“土地复垦”工艺技术进行了阐述，介绍了中铝河南分公司矿山公司方面的具体作法和成功经验。     

高合金钢铸造用涂料的试制与开发

介绍了炉爪用合金钢1Cr25Ni20Si2Re,导板用合金钢2Cr32Ni5采用串箱铸造过程中，有关镁砂粉涂料和石英粉涂料的试制。结果表明：镁砂粉涂料为不透气涂料，不太适用，而合理配方的石英粉涂料使用性能良好。     

Experimental Study on Polymer Artificial Bone with HA Coated and Fiber Liners

1Introduction HA(hydroxyapatite)wasakindofbioactiveceram ics,whichhadexcellentbiocompatibilityandtissueaffin ityinthatitscomponentsweresimilartothoseofhuman bone[1].Soitwasthebestknownhumanbonesubstitute,andunprecedentedeffecthadbeenharvestedinrecenttwo d…     

Plasma Sprayed Hydroxyapatite Coatings with Nano-hydroxyapatite Prepared by Ultrasonic Precipitation Process

Nano-particle hydroxyapatite （ HA ） was prepared with a novel ultrasonic precipitation process and the as-prepared nanopowder was used to produce hydroxyapatite （ HA ） coatings on titanium substrate via plasma spraying. The phase and the microstructare of the coating were characterized by X- ray diffraction （XRD） and scanning electron microscopy （SEM）. Results showed that spherical particles could be prepared by ultrasonic precipitation process; and a corresponding dense HA coating with molten surface and low-porosity cross-section structure was acquired. During the plasma spraying process, new phases of Ca3 （ PO4 ）2 and Ca2 P2O7 were generated. After heat-treating at 800℃ for 1 h, the contents of Ca3 （ PO4 ）2 and Ca2 P2O7 decreased while HA content increased. Tensile adhesion tests showed that the plasma sprayed coating prepared with the spherical nanoparticles exhibited high tensile bond strength.     

Water‐Stable,Magnetic Silica–Cobalt/Cobalt Oxide–Silica Multishell Submicrometer Spheres

A method to produce monodisperse magnetic composite spheres with diameters from less than 100 nm to more than 1 μm in water solution is reported. The spheres consist of a dielectric silica core and a cobalt/cobalt oxide shell which can be protected from further oxidation with an outer shell of silica or, alternatively, they can be covered with the polymer polyvinylpyrrolidone as a stabilizer. The formation of a uniform magnetic shell proceeds with the adsorption of metallic cobalt seeds, produced by the reduction of cobalt chloride with sodium borohydride, on a self‐assembled layer of polyelectrolytes on the silica core. In the second step, an outer silica shell can be formed by the hydrolysis and condensation of (3‐aminopropyl)trimethoxysilane and tetraethoxysilane. The double‐shell composite spheres show excellent sphericity, monodispersity, and a magnetic hysteresis loop at room temperature.     

WC对Cu/WC_P复合材料性能及组织的影响

通过ＷＣ含量对ＷＣ／Ｃｕ复合材料性能的影响，确定了冷压－烧结法制备Ｃｕ／ＷＣ材料的适宜ＷＣ含量为１０ｖｏｌ％左右。并就ＷＣ对该材料组织和再结晶行为的影响进行了有益的探讨。     

激光辐照制备搪瓷涂层

激光辐照制备的搪瓷涂层表面粗糙,与金属基材结合牢固。一般由 Si,Al,Na,K,B,F,O等元素组成。在激光辐照过程中 K,Na 明显地挥发,从而在涂层中的含量明显减少;Co,Ni,主要分布在界面附近;Fe 元素也由基材进入涂层,呈梯度状分布,在界面过渡区含量很高,在涂层内含量很低。搪瓷涂层的形成与激光辐照参数,特别与激光功率间存在极为密切的关系;只有选用合理的参数,才能制得搪瓷涂层。     

防腐涂料及涂装技术(Ⅷ)

防腐涂料及涂装技术讲座系列介绍防腐蚀涂料的品种和各类应用及最新产品研究进展。本讲主要介绍涂装前的表面预处理方法及表面处理质量的评定等     

棒束临界热流密度流体模化研究

在空泡物理和自然循环重点实验室氟里昂热工实验装置上进行了CHF实验 ,实验段为9 5×1 0mm元件管组成的 4× 4棒束 ,并对其开展了 4× 4棒束CHF流体模化研究。在压力 1 5 9～ 2 73MPa、质量流速 4 88～ 2 0 80kg (m2 ·s)、临界含汽率 -0 2 0～ 0 3 0的工况范围内 ,采集了 1 70个 4× 4棒束CHF实验数据 ,并与压力 9 9～ 1 6 2MPa、质量流速 2 74～ 1 4 73kg (m2 ·s)、临界含汽率 -0 2 0～0 3 4工况范围内 ,以水为工质相同棒束实验段内的 2 0 6个棒束CHF实验数据进行比较 ,发现Ahmad补偿失真模型、张振杰模型和Stevens Kirby模型在上述工况范围内不再适用于棒束CHF的模化 ,这些模型的预测偏差均大于 2 0 %以上 ,而且棒束CHF模化的流量模化因子k明显地受压力、质量流量和入口含汽率的影响。据此提出适用于上述工况范围内 4× 4棒束CHF模化的流量模化因子k的关系式 ,其CHF预测偏差在± 1 5 %以内 ,均方根误差为 7 0 5 %。     

RADIATION FIELD FROM A RECTANGULAR PLAQUE SOURCE FOR RADIATION PROCESSING

Evaluation of the Hubbell integral for an omnidirectional detector response to a rectangular plaque gamma emitting radiation source using a different numerical computation method on a personal computer was made. For a plaque consisting of several strip gamma emitters, exposure rates at different positions above the source were calculated using 'exact' evaluation and an approximate method. Optimization method is used to find source activity of each strip, so as to acquire desirable dose uniformity of the irradiated products. In uses of the Hubbell integral, by introducing appropriate programming, computation time can be saved.