Tb3+,Mn2+作为激活剂的PDP绿色荧光粉的研究

分别介绍了以Mn^2＋和Tb^3＋作为激活中心的PDP用硅酸盐体系、铝酸盐体系、硼酸盐体系和磷酸盐等体系绿色荧光粉的研究现状。在以Mn^2＋作为发光中心的绿粉中，目前研究主要集中在通过调整Mn^2＋的离子浓度、添加其他杂质，探索使用新的基质材料，或是使用不同的合成技术等方法来改进其余辉时间过长、易时效劣化以及形貌上的不足。在以Tb^3＋作为激活中心的绿粉中，为了获取在真空紫外激发条件下高的发光效率，则主要围绕寻找在VUV区域内有强吸收的基质和能够有效进行能量传递的稀土敏化剂，以及利用量子剪裁效应来使得荧光粉发光量子效率大于1等方面进行。     

摩擦焊在钢制实心抽油杆修复中的应用

通过对焊接工艺及焊后热处理工艺优化，采用摩擦焊接技术对报废抽油杆中仍有使用寿命的杆头与杆体进行了拼接，获得了性能达标的抽油杆。从而提高了旧杆的修复率．降低了采油成本。该技术可在抽油杆修复及相关行业进行推广应用。     

我国风机盘管技术现状分析

介绍了近年来我国在风机盘管技术领域的最新成果，在结构形式、强化传热、提高室内空气品质、降低噪音和提高自动控制水平等方面的技术进展情况，分析了目前风机盘管中存在的问题，并对今后的发展方向进行了展望。     

Heat Transfer Analysis for Gas-to-Liquids Transportation Through Trans Alaska Pipeline

Gas-to-liquids (GTL) technology involves the conversion of natural gas to liquid hydrocarbons. In this article, theoretical studies have been presented to determine the feasibility of transporting GTL products through the Trans-Alaska Pipeline System (TAPS). To successfully transport GTL through TAPS, heat loss along the route must be carefully determined. This study presents heat transfer and fluid dynamic calculations to evaluate this feasibility. Because of heat loss, the fluid temperature decreases in the direction of flow and this affects the fluid properties, which in turn influence convection coefficient and pumping power requirements. The temperature and heat loss distribution along the pipeline at different locations have been calculated. Fairly good agreement with measured oil temperatures is observed. The powers required to pump crude oil and GTL individually, against various losses have been calculated. Two GTL transportation modes have been considered; one as a pure stream of GTL and the second as a commingled mixture with crude oil. These results show that the pumping power and heat loss for GTL are less than that of the crude oil for the same volumetric flow rate. Therefore, GTL can be transported through TAPS using existing equipment at pump stations.     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

管内装元件强化传热的技术经济评价

提出了一种管内装元件强化传热的技术经济评价方法，此方法综合考虑了强化换热器管内传热膜系数的提高和管内流体阻力的增大，与普通的管壳式换热器相比，所带来的投资费用和使用费用变化，这个变化量可用净现值增量△NPV来表示。根据△NPV值来评价强化传热技术，从而为强化传热技术的开发和推广及进行决策提供指导。     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

Synthesis and characterization of functional gradient copolymers of glycidyl methacrylate and butyl acrylate

Epoxy-functional spontaneous gradient copolymers of glycidyl methacrylate (G) and n-butyl acrylate (B) were synthesized via atom transfer radical polymerization (ATRP). The copolymerization reactions were carried out in toluene solution at 70 °C, using methyl 2-bromopropionate (MBrP) as initiator and copper chloride with N,N,N′,N′′,N′′-pentamethyldiethylenetriamine (PMDETA) as the catalyst system. The kinetic behaviour of the statistical copolymerizations was studied in a wide composition interval with molar fractions of G ranging from 0.10 to 0.75. The synthesized copolymers were characterized by size exclusion chromatography (SEC) and nuclear magnetic resonance (NMR) spectroscopy. ¹H NMR was employed to determine the copolymer composition, demonstrating the gradient character of the copolymers along the main chain in the whole monomer conversion interval. Apart from this, the sequence distribution and stereoregularity were analyzed. These microstructural experimental data agreed well with those calculated from Mayo-Lewis terminal model (MLTM) and a Bernoullian statistic with an isotacticity parameter of σ_G = 0.28 and a coisotacticity parameter of σ = 0.30.     

4%Cr铸钢支承辊热处理工艺

以太钢1549轧机采用的4%Cr铸钢支承辊为依托,研究了该辊子从铸造成形到最终精加工之间的三次热处理工艺。最终达到其技术要求:辊身硬度65~70HS、淬硬层深≥70 mm、辊颈硬度42~48HS。