濮城油田东西区沙二下顶面微构造特征与剩余油分布

濮城油田沙二下是一个被断层复杂化了的断块型油气藏，通过对储层的精细描述表明，各砂岩组顶面微构造发育，其成因有2种，与构造作用有关的微构造及与构造作用无关的微构造，前者规模较大，后者规模通常较小，根据微构造的起伏变化和形态，可分为3类：正向微构造，负向微构造，斜面微构造，正向微构造是油气富集与控制剩余油分布的重要微构造。     

半固态ZnAl 27合金及其二次加热组织

研究了半固态ZnAl27合金及其二次加热组织。结果表明，半固态ZnAl27合金基本无宏观偏析，其组织为细小均匀的近球形非枝晶，综合力学性能远远高于常规铸造合金；二次加热后，α相进一步球化，边缘变得光滑圆整，可以满足半固态触变成形的需要。     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。     

吐丝圈径对大规格高碳盘条组织性能的影响

计算与分析了斯太尔摩冷线上盘条的吐丝圈径、搭接密度及"佳灵"装置横向布风曲线之间的关系,研究了吐丝圈径的大小对大规格82B盘条组织和性能的影响,确定了大规格82B盘条最小吐丝圈径应为980mm.     

Yield Stress and Microstructure of Set Yogurt Made from High Hydrostatic Pressure-Treated Full Fat Milk

ABSTRACT: Set yogurts were prepared from fortified milk subjected to the following processes: (a) Thermal process (85C,°C,35 min), (b) High hydrostatic pressure process (193 or 676 MPa for 5 or 30 min), and (c) Nonprocessed milk (control). Yogurts from milk treated with 676 MPa for 30 min exhibited similar yield stress and water-holding capacity (WHC) to yogurts from heated milk. Transmission Electron Microscopy (TEM) micrographs exhibited small round casein micelle aggregates without appendages in yogurts from heated milk. Yogurts from milk treated with 193 MPa and untreated milk exhibited low yield stress, low WHC, and large clusters of coalesced micelles. Mechanisms for gel formation are discussed.     

NiTi形状记忆薄膜的显微结构和力学性能

NiTi形状记忆合金薄膜具有形状记忆效应，极有希望用于制造高技术领域微电子机械系统中的微型激发器。NiTi形状记忆合金薄膜在制备和使用过程中需要高品质（衬）底材。本文利用高分辨电子显微学和高分辨分析电子显微学详细研究了硅底材NiTi形状记忆合金薄膜的NiTi／Si和NiTi／SiO2微结构体系，包括薄膜精细结构和界面反应。也研究了其显微结构和力学性能的关系。特别给出了NiTi形状记忆合金薄膜产生疲劳过程的微观过程的起因，通过高达十万个使用热循环前后样品显微结构变化的比较，发现纳米尺度上的TiNi3新相的形成导致疲劳过程的发生。如何抑制TiNi3新相形成的研究正在进行之中，这将为进一步提高NiTi形状记忆合金的使用寿命指出方向。     

45钢表面超音速电弧喷涂Ti-Al涂层的组织与性能研究

采用自行开发研制的超音速电弧喷设备，在45钢表面制成了钛铝合金复合涂层。并利用金相显微镜、X射线衍射仪、扫描电镜、电子探针，对涂层的成分、相结构、显微组织及其结合强度、显微硬度进行了研究。结果表明，利用超音速电弧喷涂设备，可以在45钢表面形成 度高、孔隙率低，结合强度较好和硬度高的Ti-Al合金涂层。     

Amorphous diffusion bonding of steel pipe and its impact toughness

An iron-based amorphous foil (FeNiCrSiB) was used as an interlayer for the amorphous diffusion bonding of low carbon steel pipes under argon flux. The microstructure and mechanical properties of the joint were analyzed using an electron probe micro-analyzer (EPMA), tensile test, bending test and impact test. The results show that the joint microstructure resembles that of the base metal and no precipitates form at the joint. Melting point depressants (B, Si) diffuse far away from the joint and the base metal element is homogenous across the joint. The joint impact toughness is greater than the base metal toughness and the mechanical properties of the joint are similar around the pipe.     

Microstructures formed by spray freezing of food fats

The spray-freezing of two food fats, tripalmitin (PPP) and cocoa butter (CB) and mixtures thereof, has been modeled experimentally using a novel single droplet freezing apparatus configured so that temperature profiles or samples for microstructure analysis can be obtained. For 2 mm diameter droplets suspended in a cold air flow at temperatures around 2–15°C, initial cooling rates were on the order of 10 K s⁻¹ and the temperature profiles could be correlated directly to DSC data collected at 20 K min⁻¹, indicating that minimal supercooling of the materials occurred in the droplet form. Microstructure analysis confirmed that PPP crystallized preferentially in mixtures, and that the surface structure was very sensitive to storage conditions. The bulk structure was much less sensitive, and the internal microstructure of the PPP droplets revealed distinct nucleation sites, which were absent from the CB: These persisted in the mixtures up to 50 wt%. X-ray analysis indicated that the fats crystallized in their more stable forms, namely, β for PPP and Form V/V1 in CB.