Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

利用SiO2包膜技术提高群青蓝颜料耐酸性的研究

采用廉价的SiO2 对群青颜料进行致密包膜 ,使群青颜料耐酸性能得到提高 ,解决了群青在聚氯乙烯型材使用中产生的变色现象 ,拓宽了应用范围     

厚度控制技术在中厚板轧制生产中的应用

本文探讨了影响中厚板厚度波动的因素，结合安钢中板厂2800mm轧机按合同轧制一批交货重量不大于理论重量船板的生产实践，总结了实际生产中实现高精度厚度控制的有效方法。     

Ideal-gas thermodynamic properties for natural-gas applications

Calculating caloric properties from a thermal equation of state requires information such as isobaric heat capacities in the ideal-gas state as a function of temperature. In this work, values for the parameters of thec _p ⁰ correlation proposed by Aly and Lee were newly determined for 21 pure gases which are compounds of natural gas mixtures. The values of the parameters were adjusted to selectedc _p ⁰ data calculated from spectroscopic data for temperatures ranging from 10 to 1000 K. The data sources used are discussed and compared with literature data deduced from theoretic models and caloric measurements. The parameters presented will be applied in a current GERG project for evaluating equations of state (e.g., the AGA 8 equation) for their suitability for calculating caloric properties.     

�¸�������в������Ȼ�����꾮�ٶȵ�;��

本文针对天然气井提高钻井速度问题,总结分析了盆地中部井身结构,水力、机械参数,聚合物钻井液,正注反挤固井等工艺技术对该地区钻速的影响。指出提高天然气井钻井速度,必须搞好系统工程,形成配套技术。     

HS－2000型双反射镜补偿式高速摄影系统研究

介绍ＨＳ─２０００双反射镜补偿式高速摄影系统的补偿原理、结构及其试验结果。     

多功能超高速计数器

脉冲信号计数是最简单的数据获取工作和最基本的测量方法。在许许多多高科技领域中,对计数器(Counter)计数分辩率提出很高要求。当前,核物理上应用的计数器都有计数率较高(最高为200MHz),结构复杂,价格昂贵的缺点。本文报导我们最新研制的一种计数率为500MHz的超高速计数器,后级采用Intersil公司生产的通用计数器电路ICM7216B,只需外接少量元件就可构成最简单多功能超高速计数系统。     

Study on Factors Affecting the Structure of High SpeedSteel Ingot Produced by ESR

ＳｔｕｄｙｏｎＦａｃｔｏｒｓＡｆｆｅｃｔｉｎｇｔｈｅＳｔｒｕｃｔｕｒｅｏｆＨｉｇｈＳｐｅｅｄＳｔｅｅｌＩｎｇｏｔＰｒｏｄｕｃｅｄｂｙＥＳＲＬｉＺｈｅｎｇｂａｎｇ；ＣｈｅＸｉａｎｇｑｉａｎＡｂｓｔｒａｃｔ：Ｔｈｅｉｎｆｌｕｅｎｃｅｏｆｔｈｅｍｅｔａｌｐ...     

冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。     

锁相技术在电子束曝光机工件台稳速控制中的应用

采用锁相技术，对电子束曝光机工件台运动实现速度环的全数字控制。设计了数字差频积分回路和数字差频比例控制器，能有效消除速度的静态误差和改善系统的动态特性。