粉末冶金法制备PSZ/Mo复合材料的研究

本文采用粉末冶金法制备了不同成分的PSZ/Mo复合材料。并对其密度、弹性模量和热膨胀系数进行了测量和分析 ,用XRD进行了物相分析。实验结果表明 :纳米氧化锆的烧结性能比金属钼好 ;弹性模量估算选用简单混合法则进行计算时应进行修正 ;钼和氧化锆在烧结时不发生化学反应。通过热压PSZ/Mo功能梯度材料的断口扫描分析发现 :虽然金属钼和纳米氧化锆具有一定增韧作用 ,但材料断裂方式仍以脆性断裂为主     

复合材料超声波直线电机的运动控制

针对复合材料超声直线电机振动体具有两个固有频率的特点，设计了具有频率跟踪特性的超声直线电机驱动器，利用激励信号频率变化改变电机运动方向，实现了超声直线电机的运动控制。     

Preparation and Application of Active Composite Antibacterial Material Containing Ag~ and Zn~(2 )

1Introduction Harmfulbacteriaexistanywhereintheworldsuchas soil,air,water,surfacesofobjectsandourskins,etc.Thenumberofbacteriumisenormous,withmanydiffer entspecies.Theyhavethreatenedthehealthofhuman beingsseriously.Withthedevelopmentofeconomyand environme…     

Preparation of Laminin-apatite-polymer Composites Using Metastable Calcium Phosphate Solutions

A synthetic polymer with a laminin-apatite composite layer on its surface would be useful as a percutaneous device. The preparation of such a composite was attempted in the present study using poly（ ethylene terephthalate ） （PET） and polyethylene （PE） as the synthetic polymer. PET and PE plates and those pretreated with an oxygen plasma were alternately dipped in calcium and phosphate ion solutions, and then immersed in a metastable calcium phosphate solution supplemented with laminin （ LCP solution ）. The PET and PE plates pretreated with an oxygen plasma formed a uniform and continuous layer of a laminin-apatite composite on their surfaces. In contrast, the PET and PE plates that had not been pretreated with an oxygen plasma did not form a continuous layer of a laminin-apatite composite on their surfaces. The hydrophilic functional groups on the PET and PE surfaces introduced by the plasma treatment were responsible for the successful laminin-apatite coruposite coating.     

复合绝缘子老化评估方法浅析

复合绝缘子老化是用户十分关心的问题。笔者介绍了两种判别复合绝缘子老化程度的方法,并通过实例,分析了这两种方法的优点以及存在的问题。     

JOINING MECHANISMS OF β''''-Al2O3 CERAMIC AND PYREX GLASS TO Al MATRIX COMPOSITE

The bonding of β'-Al2O3 and pyrex glass to Al matrix composites by anodic bonding process is achieved. The microstructure of the bonded interface and the joining mechanisms are analyzed with scanning electron microscope (SEM), energy dispersive X-ray fluorescence spectrometer (EDX). It is observed that the bonding region across the interface consists of the metal layer, oxide transitional layer and the ceramic layer, with the transitional layer composed of surface region and sub-surface region. The bonding process can mainly be categorized into anodic bonding process and solid state diffusing process. The pile-up of the ions and its drift in the interface area are the main reasons for anode oxidation and joining of the interface. The temperature, voltage and the drift ions in the ceramic or glass during the bonding process are the essential conditions to solid state diffusing and oxide bonding at the interface. The voltages, temperature, pressure as well as the surface state are the main factors that influence the anodic bonding.     

聚丙烯酸酯/醇酸树脂复合乳液的合成与表征

用乳液聚合法合成了聚丙烯酸酯/醇酸树脂复合乳液,研究了醇酸树脂组成和用量及聚合条件对动力学和复合乳液性能的影响。结果表明,醇酸树脂对乳液聚合有明显的阻聚作用,而且这种阻聚作用随醇酸树脂中马来酸酐含量的增加而加剧。升高聚合温度和增加引发剂用量均有利于改善乳液的机械稳定性。随着醇酸树脂用量的增加,复合乳液的机械稳定性和涂膜的耐水性逐渐提高;醇酸树脂中马来酸酐含量增加,乳液机械稳定性提高,当醇酸树脂中马来酸酐质量分数为2 4%时,涂膜具有最佳的耐水性。     

In situ formation of multi scale reinforcing phases to improve performance of Al2O3-SiC C castables

In order to improve the physical properties and slag corrosion resistance of refractory materials for hot metal pretreatment, different contents of composite metal powders (CMP) were introduced into Al2O3-SiC-C refractory castables. The effect of CMP on the microstructure, physical properties and slag corrosion resistance of Al2O3-SiC-C refractory castables were studied. The results show that the multi scale reinforcing phases including flake crystals, rod shaped fibers, filamentous fibers and whiskers are in situ formed in the samples with addition of CMP, which result to the improvement of the cold modulus of rupture and cold crushing strength. When the addition of CMP is 6 wt.%, the high temperature modulus of rupture increases by 231%, the thermal shock resistance increases by 77% after thermal shock by water cooling 5 times and the percentage of the slag resistant area reduces by 37.2%.     

未增塑聚氯乙烯(PVC-U)异型材配方基础

PVC-U异型材配方十分复杂,常用原料通常在10种以上。根据大连实德集团实际生产情况,这10多种原料通常以7大组分的方式进行配料和生产。文中就该配方中7大组分的分类、特点及应用情况分别进行了详细介绍。     

书立复合冲裁模的设计

介绍了安装在液压试验机上的一种集冲裁、切口作用于一体的复合冲裁模的设计，解决了没有压力机的情况下冲裁件的加工问题。