粉土界面恒刚度循环剪切试验研究

竖向循环荷载作用下桩土界面的作用机理是研究桩土摩擦疲劳的关键。针对循环荷载作用下桩-粉土界面的剪切性能,使用改进的剪切试验装置在恒刚度条件下进行循环剪切试验,研究循环次数、累积位移和法向刚度对其摩擦疲劳性能、循环后单调剪切性能的影响。试验结果表明,粉土在循环剪切过程中,法向应力和剪应力在初始10个循环内随循环数增加快速衰减,随着循环进行,逐渐趋于稳定;单次循环内在剪切位移方向变化时,土体呈现表现出剪缩-剪胀-剪缩交替现象,总体变形呈现剪缩的趋势;循环荷载作用下,粉土界面的法向应力和剪应力随法向刚度增大衰减速率增大,达到稳定的累积循环位移越小;粉土循环后的单调剪切、法向应力恢复的单调剪切的剪应力比小于首次单调剪切试验值,且法向应力恢复的循环后剪切试验的剪胀程度较小,表明循环剪切过程中界面处粉土颗粒棱角破碎,颗粒变得光滑。在对试验数据分析的基础上,提出了与累积位移、法向刚度和初始应力相关的无量纲累积位移,建立了法向应力和界面摩擦角随累积位移的衰减方程。     

某340矫直机上辊快开机构裂纹原因分析及预防措施

340管线矫直机是太原重工成熟产品,在国内占有较大市场,并出口印度、印尼、缅甸、埃及等国际市场。出口印度矫直机在质保期内出现主缸裂纹问题,为探明问题原因并杜绝类似情况发生,快开机构设计静强度分析、疲劳强度分析及生产加工过程等方面探查裂纹原因并提出几点预防措施。     

Preparation of nanocrystalline nickel oxide from nickel hydroxide using spark plasma sintering and inverse Hall-Petch related densification

Nanocrystalline nickel oxide (NiO) was prepared from nickel hydroxide by Spark plasma sintering (SPS) and the mechanisms involved in the densification of NiO were studied. Reverse precipitated nickel hydroxide powders were SPS processed at 400, 600 and 700?°C with 70?MPa pressure. Pure NiO with 12?nm crystallite size formed after 400?°C sintering process. However NiO grains had grown to 18 and 38?nm after 600 and 700?°C sintering respectively. NiO pellets prepared using 600 and 700?°C SPS sintering schedules had relative densities of 83% and 94% respectively. Two displacement rate regimes were observed during densification of NiO in both 600 and 700?°C sintering processes. Decomposition of nickel hydroxide and particle sliding of NiO led to first displacement rate maximum while inverse Hall-Petch based plastic deformation facilitated densification during the constant second displacement rate regime. No densification occurred during sintering holding times indicating the limited role that diffusion played during densification.     

Q690钢焊接接头微观组织对冷裂纹的影响研究

分析了Q690钢手工电弧焊与气体保护焊焊接冷裂纹产生与微观组织的联系。结果表明: 焊接冷裂纹起源于斜Y坡口根部, 沿熔合区、焊缝扩展至焊缝表面;2种工艺焊接的接头组织硬度均较母材高, 而塑性较差。热影响区为马氏体、贝氏体与铁素体混合组织, 焊缝组织由先共析铁素体、侧板条铁素体、贝氏体和针状铁素体等组成, 针状铁素体抗裂纹扩展能力较其他组织强。在2种焊接方法对应断口中观察到了冷裂纹起裂、扩展与断裂区的不同形貌, 起裂与扩展区存在塑性变形, 而断裂区为解理断裂。     

Size-controlled synthesis of Mo powders via hydrogen reduction of MoO2 powders with the assistance of Mo nuclei

The size-controlled preparation of Mo powders is always a challenge and important task in the molybdenum metallurgy. In the current study, Mo powders with controllable sizes are synthesized by hydrogen reduction of MoO₂ powders with the assistance of Mo nuclei in the range of 900–1100 °C. The influences of the particle sizes of Mo nuclei, the additive amount as well as reaction temperature on the morphology and particle sizes of the final products are studied. For the hydrogen reduction of MoO₂ without any additive, the obtained Mo powders always have large particle sizes. However, the addition of small amounts of nuclei in MoO₂ can help Mo nucleate dispersedly, and the growth of Mo could be also controlled by adjusting the sizes of added nuclei, amount of addition and the reaction temperature. With the addition of Mo nuclei, the different sizes of Mo powders with the good dispersity can be prepared. As adding commercial Mo powders with the particle size of about 2.03 μm, the micron-sized Mo powders ranged from 2.11 μm to 3.25 μm could be prepared. While for the case of adding ultrafine Mo nuclei of about 170 nm, Mo powders from 0.28 μm to 0.88 μm can be obtained. Moreover, the more the amounts of nuclei added and the lower the reaction temperature (in the range of 900–1100 °C) is, the smaller the particle size of the prepared Mo powder will be. The current method is a facile and feasible method, and is potential to be used for industrial production of Mo powder with controllable particle sizes.     

Effect of microstructure on the fatigue crack growth behaviour of a near-α Ti alloy

Fatigue crack growth behaviour of Ti–6Al–2Zr–1.5Mo–1.5V (VT-20 a near-α Ti alloy) was studied in lamellar, bimodal and acicular microstructural conditions. Fatigue crack growth tests at both increasing and decreasing stress intensity factor range values were performed at ambient temperature and a loading ratio of 0.3 using compact tension samples. Lamellar and acicular microstructures showed lower fatigue crack growth rates as compared to the bimodal microstructure due to the tortuous nature of cracks in the former and the cleavage of primary α in the latter. The threshold stress intensity factor range was highest for acicular microstructure.     

In situ measurements of human cough aerosol hygroscopicity

The airborne dynamics of respiratory droplets, and the transmission routes of pathogens embedded within them, are governed primarily by the diameter of the particles. These particles are composed of the fluid which lines the respiratory tract, and is primarily mucins and salts, which will interact with the atmosphere and evaporate to reach an equilibrium diameter. Measuring organic volume fraction (OVF) of cough aerosol has proved challenging due to large variability and low material volume produced after coughing. Here, the diametric hygroscopic growth factors (GF) of the cough aerosol produced by healthy participants were measured in situ using a rotating aerosol suspension chamber and a humidification tandem differential mobility analyser. Using hygroscopicity models, it was estimated that the average OVF in the evaporated cough aerosol was 0.88 ± 0.07 and the average GF at 90% relative humidity (RH) was 1.31 ± 0.03. To reach equilibrium in dry air the droplets will reduce in diameter by a factor of approximately 2.8 with an evaporation factor of 0.36 ± 0.05. Hysteresis was observed in cough aerosol at RH = ∼35% and RH = ∼65% for efflorescence and deliquescence, respectively, and may depend on the OVF. The same behaviour and GF were observed in nebulized bovine bronchoalveolar lavage fluid.     

某轻型载货车储气罐支架振动断裂分析与优化

为了有效解决某轻型载货车储气罐支架的断裂故障,首先基于建立的储气罐支架有限元模型进行振动特性分析,分析结果表明其前三阶固有频率接均处于发动机激励频率范围之外,不会产生共振。其次测试各种道路的时域载荷,测试结果表明其中角度搓板路的激励频率与储气罐支架第一阶固有频率相接近,从而引起共振,不满足振动特性要求。然后对其进行振动强度分析,分析结果表明其应力水平不达标,其最大应力点与开裂处一致。再对其进行振动疲劳寿命预测分析,分析结果表明其疲劳寿命也不达标,其危险点也与失效位置相同。再采用集成平台对储气罐支架的结构进行优化设计,优化之后其模态频率、振动强度和振动疲劳均符合性能要求,并且其重量也有所减轻,总体优化效果较佳。最后整车试验结果表明优化之后储气罐支架的振动大幅度降低,并且没有发生失效。     

一类两性分枝过程条件均值增长率的极限性质

本文主要研究随机环境中配对依赖人口数两性 Galton-Watson 分枝过程的条件均值增长率的极限性质．利用上可加函数的性质，得到配对单元平均增长率的极限性质和该过程条件均值的上界和下界．文中给出了关于过程条件均值增长率的两个序列，利用配对单元平均增长率的性质，获得了这两个序列的极限性质．随机环境中配对依赖人口数两性分枝过程比较复杂，本文的结论推广了现有的研究成果．