悬索缆道(带铅鱼)在义棠水文站的应用

文中以山西省首家悬索自动化测流缆道在义棠水文站淤泥质河床的应用为例，叙述了该站缆道的设计、安装、试验研究的基本情况、设计指标、缆道总体布设、信号传输线路的设计及工作原理等。“失重”开关与河底开关的双重保险功能是解决我国北方地区淤泥质河床信号的产生与传输的关键。文中对此做了具体叙述，旨在为类似的缆道工程设计采用时参考。     

准噶尔盆地白家海地区侏罗系聚煤作用与层序地层

煤层在层序划分与对比中具有十分重要的参考意义。以准噶尔盆地白家海地区侏罗系为例，通过对该地区几个聚煤时期的碎屑物质的供应程度、古地貌格局、湖平面变化（基准面变化）、气候及古植物等内在与外在因素的分析，并结合侏罗系高分辨率层序地层研究，认为该地区侏罗系煤层受多种因素控制，并主要发育于基准面稳定上升的早期，且与层序的时空演化存在着有机联系。     

长江口北支水道水沙特性分析

从实测资料出发,结合水流数值计算成果,对长江口北支水道的水流、泥沙和含盐度等资料进行分析,得出了北支水道的水沙特性,并分析了水沙变化与河床变化的相互关系.北支水道在1958年南通河段河势控制后,径流分流比逐年下降,并渐趋稳定于3%左右.北支水道受径流影响越来越小,主要受潮流作用.随着水沙特性的逐年变化,北支水道0 m以下槽蓄容量逐年减小,并渐趋稳定,北支上段为逐年淤积最快的区域.由此反过来影响了水沙条件的进一步变化,使北支上段平均潮差增加,北支的会潮点由崇头附近下移至青龙港附近.     

下游为干河床的溃坝水流数值模拟

应用二阶TVD—MacCormack格式计算了含间断波的二维浅水流动．模拟算例为下游是干河床、瞬间部分坝体溃决形成的溃坝水流运动．针对该格式，采用恰当的限制器使得解既不产生过大耗散，又具有高分辨率．     

油气沉积学原理及其在勘探开发中的应用

本文以油气藏形成条件中的生、储、盖、运、圈为纲讨论了油气勘探沉积学;以油气藏开发过程中与沉积、成岩的关系讨论了油气开发沉积学。在油气勘探沉积学中重点论述了陆相沉积与储层及圈闭的关系;在油气开发沉积学中重点论述了储层研究的基础—储层的沉积属性和成岩特征。强调储层沉积、成岩研究应成为储层评价最重要的内容。     

Spouted and spout-fluid bed combustors 1: Devolatilization and combustion of coal volatiles

The devolatilization and volatile combustion of a single coal particle in spouted and spout-fluid beds have been studied. The results showed that the flame extinction time increases with the particle diameter, and decreases with the bed temperature. When the bed temperature and the air flow rate were fixed, the operation modes (spouted or spout-fluid bed) showed less effect on the mean flame extinction time. A mathematical model of the spouted bed mode for preignition and postignition periods has also been developed assuming the devolatilization rate to be controlled by heat transfer and multireaction pyrolysis kinetics based on volatile products. Ignition, heat transfer back from the volatile flame to the particle surface, variation in flame temperature, and the hydrodynamics of SB are taken into account. The model predictions, with some adjusting parameters, were in good agreement with experimental results.     

The Problem of Estimating the Uncertainty of the Fixed Point Temperature Due to the Presence of Impurities

The main problems in estimating the uncertainty due to the presence of impurities in the material: the absence in the documents of a unique definition of the quantity being measured – the fixed point temperature, the lack of agreed methods of realizing the fixed points and the insufficient justification of the equations used for the estimate, are analyzed. The results of a measurement of the melting point of gallium are presented, which differ in the conditions in which they were realized – with one and two liquid-solid interfaces and different solidification conditions, are presented. The reasons for the considerable difference between the values of the temperatures obtained in these experiments are discussed.     

Results of familiarization of and prospects for a procedure for the burning of wastes in a vortical fluidized bed

Problems that have arisen during tune-up of the production line for the thermal processing of solid household waste by the method of burning in a vortical fluidized bed (principally, a new technology for Russia), and means of their solution are presented. Investigative studies are cited. __________ Translated from élektricheskie Stantsii, No. 6, pp. 20–26, August, 2006.     

一种控制盐层段井眼闭合率的钻井液密度新公式

针对钻井过程中钻遇的盐层段井眼蠕变缩径问题,利用弹塑性力学理论,蠕变本构方程采用Heard蠕变方程,在平面应变和均匀地应力假设下,推导出控制井眼收缩的钻井液密度新公式,该公式与前人推导的公式不同。通过理论分析,指出产生差异的根本原因在于蠕变应力差(极坐标下表示的径向应力与切向应力之差)公式的推导上,用有限元法计算结果对理论公式进行检验,证明是可行的。对文中的力学模型采用有限元法建模、求解,利用求解结果对各应力差公式进行验证,得出:根据文中公式计算结果与有限元法计算结果完全一致,而据前人公式计算结果偏离有限元计算值较大,从而间接证明了该钻井液密度新公式的推导更严密,更准确。     

Scale‐up and Spouting of Two‐Dimensional Beds

The objective of this paper is to present an analysis on the scale‐up procedure of two‐dimensional spouted beds. The task was carried out with three different beds measuring 0.15, 0.30 and 0.80 in width. The conditions of scale‐up were studied through geometrical similitude analysis. Some parameters of scale were adimensionalised, tested and validated in order to propose relationships capable of predicting values of dependent properties. Those relationships should be followed in a prototype of an equipment of industrial scale. The study permitted the development of correlations to predict values of maximum pressure drop, minimum spout velocity and maximum height of spouting.