聚二甲基硅氧烷涂层材料的研究

采用一定粘度的聚二甲基硅氧烷为基体，加入适量填料和助剂，成功制备了室温硫化硅橡胶涂层。研究了气相法SiO2和交联剂对涂层材料的影响，并进行了TG和SEM测试。研究结果表明：填料的添加明显改善了涂层的力学性能和耐高温性能，拉伸强度迭1．42MPa，可耐温288℃；并且该涂层有较好的耐水和耐酸、盐性能，耐碱性能有待进一步改善。     

TiC－Al_2O_3复合材料的自蔓延高温合成和致密化

以ＴｉＯ＿２，Ａｌ和Ｃ三种粉末为原料，采用自蔓延高温合成和加压的方法制备了ＴｉＣ－Ａｌ＿２Ｏ＿３复合材料。在１ＧＰａ压力下，可使样品达到理论密度的９５％。对未反应样品燃烧前在真空状态下预热脱气，则密度可达９８％。为避免样品开裂，必须控制冷却速度。对合成产品进行了Ｘ射线分析，表明从ＴｉＯ＿２，Ａｌ，和Ｃ三种粉末原料制备密实的ＴｉＣ－Ａｌ＿２Ｏ＿３复合材料是可能的。     

漆酶改善分离木素和OCC纸浆特性的研究

应用漆酶处理纤维素酶分离酶解木素和OCC(Old corrugated containers)纸浆,结果表明:木素在漆酶处理过程中会发生降解,经漆酶处理后再经加热处理会使木素发生聚合,木素降解主要发生在高分子量木素部分,而聚合作用主要发生在低分子量木素之间;木素经漆酶处理后,酚羟基的含量略有增加,这是由于在漆酶处理木素的过程中,木素不但发生酚氧自由基的离域现象,而且还有高分子量的木素发生降解产生了新的酚羟基;经不同用量的漆酶处理的OCC纸浆手抄片的湿环压指数和湿抗指数与对照样相比均有明显提高,特别是漆酶用量为24 U/g时,湿环压指数达到4.1 N.m/g,提高了41%。经不同用量的漆酶处理的OCC纸浆干环压强度和干抗张强度与对照样相比略有提高,但提高的幅度不大。     

Comparison of the Effect of a Hydrocarbon Oil and a Terpene Tackifier on the Autohesion of Styrene-Butadiene Rubber

Blends of uncrosslinked styrene-butadiene rubber (SBR) with a terpene tackifier resin or a naphthenic oil have been characterized, and their autohesion and cohesion determined using a T-peel geometry. SBR/oil blends are homogeneous at all proportions, while SBR/resin blends, based on DSC and DMA analysis, undergo bulk phase separation at about 50% resin. However, migration of tackifier to the surface region is proposed at much lower resin contents. Compositions diluted with oil have autohesion similar to the neat SBR. This is attributed to compensating effects; although oil hastens self-bond formation by increasing chain mobility, this is nearly equally balanced by more facile chain separation during bond rupture. In short, oil-diluted compositions are soft and weak. On the other hand, SBR compositions containing small amounts of resin have high autohesion. Resin-diluted specimens deform easily at low strain, just as those containing oil, but intertwined chains of the former have greater resistance to separation, due at least in part to higher glass transition temperatures. It is proposed that autohesion is further enhanced by migration of tackifier to the surface. This causes SBR/resin compositions to be both soft and strong-a necessary condition for high autohesion.     

UHMWPE/LDPE复合材料拉伸破坏的声发射特性研究(Ⅱ)

本文续“UHMWPE/LDPE复合材料拉伸破坏的声发射特性研究(Ⅰ)”,进一步研究了UHMWPE/LDPE复合材料拉伸破坏的声发射特性,具体研究了[0°]、[90°]在拉伸破坏过程中声发射参数特征,并对拉伸破坏机理进行了初步的研究。     

Tensile Stress Relaxation of Alumina at High Temperature

The development of a tensile testing methodology for ceramics which enables a stress vs strain-rate response to be measured at high temperature is described. The test involves a carefully controled stress relaxation test at constant total strain using an experimental procedure and phenomenological analysis previously developed for metallic materials. It is demonstrated here with preliminary tests on alumina at 1050° and 1150°C. This offers, with further development, the possibility of establishing design stresses associated with low strain-rate behavior for structural applications. The results demonstrate that data covering four decades of strain rate may be generated in tests lasting a few hours. The inelastic strain consists of substantial anelastic recoverable strain in addition to a permanent creep strain.     

TiB2的SHS合成过程理论分析

在ＴｉＢ２陶瓷材料的自蔓延高温合成（简称ＳＨＳ）过程中，通过改变原料的起始温度，稀释剂的含量和原始颗粒的尺寸等都可以调节合成过程的绝热温度，产物中熔融相的含量，以及燃烧波蔓延的速度，人而最终影响合成产物的结构和性质。本文对上述各种关系进行了理论计算和分析，其结果对实际合成与制备过程将有着重要的指导作用。     

偶联剂处理对碱式硫酸镁晶须填充UP树脂浇铸体力学性能的影响

利用钛酸酯类偶联剂NDZ101、NDZ401和硅烷类偶联剂KH550、KH570对碱式硫酸镁晶须进行处理,研究了几种偶联剂及其加入比例对晶须填充不饱和聚酯树脂(UP)浇铸体力学性能的影响,并结合应力-应变曲线和SEM的图片,对试验结果进行了讨论。实验结果表明,采用偶联剂处理晶须可改善其填充UP树脂浇注体的拉伸强度、拉伸模量、弯曲模量和冲击强度。其中,采用2%KH570进行处理,拉伸强度改善幅度最高,可提高47.54%;采用3%NDZ101进行处理,拉伸模量和弯曲模量均获得最大幅度的提高,分别为65.99%和69.33%;而采用4%KH550进行处理,却可最大幅度地提高冲击强度,为29.21%。对弯曲强度而言,偶联剂处理总体上对其影响效果不如其它的力学性能那样明显。相对而言,硅烷类偶联剂的效果优于钛酸酯类的偶联剂。加入4%KH570和5%KH550时获得的弯曲强度最大,分别为54.43MPa和53.19MPa,较未处理的浇铸体弯曲强度分别提高了25.10%和22.25%,而采用NDZ101或NDZ401,弯曲强度值却基本上都下降。碱式硫酸镁晶须填充UP树脂浇铸体的断裂属于脆性断裂。     

大型矿车用减速机齿轮系统的疲劳分析

提出一种基于"放大因子"、采用二维平面单元模拟三维实体动态工况的计算疲劳的方法,对某矿车减速机齿轮系统进行疲劳分析,得到太阳轮、行星轮和扭力管在不同抗拉强度下的疲劳寿命.结果表明:太阳轮和扭力管最易发生疲劳破坏;齿轮寿命对抗拉强度的依赖性较敏感;得出的齿轮系统热处理后的抗拉强度建议值能为设计提供参考,且该方法能大大提高计算效率.     

聚苯硫醚/聚四氟乙烯复合材料的研究

制备并研究了PPS/PTFE合金的热行为、力学性能以及摩擦学性能,并对其微观形态进行了观察。实验结果表明,此合金的耐热性能相对于聚苯硫醚纯树脂有明显的提高,而且聚四氟乙烯的加入可以改善聚苯硫醚的力学性能及摩擦磨损性能。