Cr对低碳Si-Mn系TRIP钢组织与力学性能的影响

主要研究了Cr对低碳Si-Mn系TRIP钢组织与力学性能的影响。首先利用Formastor-F型膨胀仪测定了含Cr和不含Cr两种低碳钢的连续冷却转变(CCT)曲线,分析指出了Cr对连续退火工艺的潜在影响;然后采用Gleeble-3800热/力模拟试验机对两种钢的薄板试样进行了连续退火模拟实验,并通过拉伸试验测定了力学性能;最后采用金相、扫描电镜、X-射线衍射分析等技术考察分析了两种钢的显微组织。结果表明:含Cr的TRIP钢的组织比较细小,铁素体晶粒近似等轴分布;两种TRIP钢的残余奥氏体含量相近,但含Cr钢的残余奥氏体中的含碳量较高。分析认为这是由于含Cr钢在热轧阶段较易生成细小的组织,而在热处理阶段则抑制贝氏体的生成,最终获得稳定的残余奥氏体。     

Effects of Y and Ce on Microstructures and Properties of Nb-Si System Composites

The effects of yttrium and cerium on microstructures and properties of Nb-Si system composites were investigated by scanning electron microscopy( SEM), energy dispersive spectrum(EDS), X-ray diffraction(XRD) and high temperature oxidation experiments.It is found that the coarse primary silicide phase became finer and more homogeneous with Y and Ce addition.The results of high temperature oxidation experiments show that the oxidation rates of NbSi system composites with an appropriate amount of Y and Ce decrease compared with those of alloys without Y or Ce addition, and oxidation products mainly distribute along the phase boundaries between the Nb solid solution and silicide.     

Choice With Initial and Terminal Link Reinforcement: An Alternative Self-Control Paradigm.

Self-control is demonstrated when a less desirable immediate outcome is chosen to ensure a substantially better future. In a novel animal analogue of this situation, primary reinforcement was delivered in both the initial and terminal links of a concurrent chain schedule. Rats made initial link choices between equal amounts of ethanol-free or ethanol-containing milk. Choosing the ethanol-free reinforcer resulted in delivery of the larger terminal link reinforcer and was thus analogous to self-control. Self-control decreased as the delay between initial and terminal links increased. The results have implications for human choice situations where decisions are made between two immediately available reinforcement alternatives each associated with a different delayed outcome. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Threshold and growth mechanism of fatigue cracks under mode II and III loadings

ABSTRACT The fatigue crack growth behaviour of 0.47% carbon steel was studied under mode II and III loadings. Mode II fatigue crack growth tests were carried out using specially designed double cantilever (DC) type specimens in order to measure the mode II threshold stress intensity factor range, ΔK_IIth. The relationship ΔK_IIth > ΔK_Ith caused crack branching from mode II to I after a crack reached the mode II threshold. Torsion fatigue tests on circumferentially cracked specimens were carried out to study the mechanisms of both mode III crack growth and of the formation of the factory‐roof crack surface morphology. A change in microstructure occurred at a crack tip during crack growth in both mode II and mode III shear cracks. It is presumed that the crack growth mechanisms in mode II and in mode III are essentially the same. Detailed fractographic investigation showed that factory‐roofs were formed by crack branching into mode I. Crack branching started from small semi‐elliptical cracks nucleated by shear at the tip of the original circumferential crack.     

热处理对Ti-25V-15Cr-2Al-2Mo-0.2C合金组织稳定性的影响

研究了热处理对Ti-25V-15Cr-2A1-2Mo-0.2C阻燃β钛合金组织稳定性的影响。结果表明，高温固溶并直接时效处理导致合金β基体上析出较多的α相沉淀，尤其在随后的热暴露组织中形成了恶化合金塑性的连续晶界α膜。然而，若在时效前再进行一次低温固溶处理则可明显减少α相的析出数量，合金的热稳定性因此而得到显著改善。     

铀表面初始氧化行为的电子能量损失谱研究

利用俄歇电子能谱仪获取了表面清洁的铀及其在氧化过程中的电子能量损失谱(EELS)，研究这些电子能量损失谱线显示：清洁表面铀的等离子损失的实验值与理论值较为符合；随着氧化程度的加剧，体等离子体(BP)、表面等离子体(SP)以及价带间跃迁所造成的电子能量损失峰发生了明显的连续偏移和强度的变化，表明室温下清洁表面铀暴露微量纯氧后，在铀表面上发生了U→UO→UO2初始氧化过程。同时，又采用了俄歇电子能谱(AES)和X射线光电子谱(XPS)对照分析了铀的初始氧化过程。     

Evolution of grain structure in thin film reactions

In this paper, we examine, both experimentally and theoretically, the kinetics of formation and microstructure of product phases in thin film reactions, using the Nb/Al and Ti/Al systems as our prototypes. The results of calorimetry and microscopy studies are interpreted using simple kinetic and morphology models. In particular, the kinetic models employed here focus on the nucleation and growth components of the phase formation process and the morphology models provide a starting point for the classification of product grain structures. An erratum to this article is available at .     

β″－Al_2O_3陶瓷的强化和韧化

研究了稳定ＺｒＯ＿２和部份稳定ＺｒＯ＿２对β″－Ａｌ＿２Ｏ＿３陶瓷的强化和韧化作用，观察了不同种类、不同含量的ＺｒＯ＿２对β″－Ａｌ＿２Ｏ＿３陶瓷的显微结构、力学性能和电导率的影响，探讨了β″－Ａｌ＿２Ｏ＿３的韧化机理。     

以YAG为添加剂的气压烧结氮化硅

本文以添加ＹＡＧ的反应烧结氮化硅（ＲＢＳＮ）为前驱体，采用气氛加压烧结的工艺，在０．５～９．０ＭＰａ氮气压力范围，研究了不同氮压对烧结体的密度、相组成、强度和显微结构的影响及其相互间的关系。研究表明，通过改变氮气压力能有效地调控材料的显微结构，材料的性能又受控于显微结构的变化。