Nonlinear response in glass fibre non-crimp fabric reinforced vinylester composites

This paper addresses the nonlinear stress-strain response in glass fibre non-crimp fabric reinforced vinylester composite laminates subjected to in-plane tensile loading. The nonlinearity is shown to be a combination of brittle and plastic failure. It is argued that the shift from plastic to brittle behaviour in the vinylester is caused by the state of stress triaxiality caused by the interaction between fibre and vinylester. A model combining damage and plasticity is calibrated and evaluated using data from extensive experimental testing. The onset of damage is predicted using the Puck failure criterion, and the evolution of damage is calibrated from the observed softening in plies loaded in transverse tension. Shear loading beyond linear elastic response is observed to result in irreversible strains. A yield criterion is implemented for shear deformation. A strain hardening law is fitted to the stress-strain response observed in shear loaded plies. Experimental results from a selection of laminates with different layups are used to verify the numerical models. A complete set of model parameters for predicting elastic behaviour, strength and post failure softening is presented for glass fibre non-crimped fabric reinforced vinylester. The predicted behaviour from using these model parameters are shown to be in good agreement with experimental results.     

航空发动机复杂扭曲叶片分步电解加工研究

为实现复杂扭曲叶片在较小间隙下的稳定加工,提出了一种分步式电解加工的工艺方法,建立了复杂扭曲叶片小间隙(0.2 mm)和大间隙下(0.5 mm)扭曲流道的流道模型,采用有限元法进行了流场仿真研究,结果表明增加流道间隙可以解决流道中涡流和流场紊乱的问题。开展了复杂扭曲叶片小间隙连续式加工和分步式加工的试验研究。结果表明,采用小间隙连续式加工,当阴极进给至3.8 mm位置时,在叶片排气边靠近叶根流道扭曲处出现短路打火情况;而采用分步式加工方式能够实现加工的顺利进行。     

Electromagnetism-like algorithms for optimized tool path planning in 5-axis flank machining

Optimization of tool path planning using metaheuristic algorithms such as ant colony systems (ACS) and particle swarm optimization (PSO) provides a feasible approach to reduce geometrical machining errors in 5-axis flank machining of ruled surfaces. The optimal solutions of these algorithms exhibit an unsatisfactory quality in a high-dimensional search space. In this study, various algorithms derived from the electromagnetism-like mechanism (EM) were applied. The test results of representative surfaces showed that all EM-based methods yield more effective optimal solutions than does PSO, despite a longer search time. A new EM-MSS (electromagnetism-like mechanism with move solution screening) algorithm produces the most favorable results by ensuring the continuous improvement of new searches. Incorporating an SPSA (simultaneous perturbation stochastic approximation) technique further improves the search results with effective initial solutions. This work enhances the practical values of tool path planning by providing a satisfactory machining quality.     

Densification mechanism during reactive hot pressing of B4C-ZrO2 mixtures

The densification behaviors of pure B₄C and B₄C-ZrO₂ mixtures were compared during hot pressing. The results showed that in-situ formed ZrB₂ effectively enhanced the densification process of B₄C-ZrO₂ mixtures, more significantly during the intermediate stage. Within the relative density ranging from 0.75 to 0.90, the B₄C-15?wt%ZrO₂ mixture (B15Z) achieved the maximum densification rate as twice much as that of pure B₄C. The stress exponent n>3 indicated plastic deformation was the dominant densification mechanism of B15Z. The viscosities of plastic flow were evaluated using Murray-Rodger-William equation and the viscosity of B15Z was only a quarter of that in pure B₄C. The sintering activation energy was calculated to be 305.9?kJ/mol for pure B₄C and 197?kJ/mol for B15Z, respectively. It was proposed that the lower viscosity of plastic flow and activation energy accelerated the sliding and propagating motions of plastic flow, by which underlain the enhanced densification behaviors of B₄C-ZrO₂ mixtures.     

强化研磨加工中喷射角度对GCr15轴承钢板塑性变形的影响

利用ABAQUS有限元仿真软件研究不同喷射角度强化研磨加工GCr15轴承钢板过程的塑性变形,得到不同喷射角度与等效塑性应变沿真实路径距离的关系,并通过拉伸试验进行验证。喷射角度为90°的强化研磨加工伸长率为1.4%,相比未经过强化研磨加工的伸长率数值缩减了2.0%。断口收缩率由空白组的4.9%降低到喷射角为90°的2.2%。结合仿真和试验可知,强化研磨加工中喷射角度越大,塑性变形能力越低,材料加工越难。     

Microstructure,mechanical properties and bio-corrosion properties of Mg-HA bionanocomposites fabricated by a novel severe plastic deformation process

This research investigates the alterations in microstructure, mechanical properties, and corrosion behavior of binary magnesium-hydroxyapatite bionanocomposites with 2, 5, and 10 wt%HA. By mixing Mg and HA powders with different percentages of HA contents, a combined method of cyclic extrusion compression (CEC), equal channel angular pressing (ECAP) and conventional extrusion were employed to consolidate the mixture of powders. All composites were examined. The results indicate that the addition of hydroxyapatite to magnesium improves the mechanical properties, but these properties are deteriorated with the hydroxyapatite content of over 5 wt%. The corrosion behavior of the composites was examined by immersion test, mass loss and polarization tests in Hank’s solution. The results indicate that Mg-5HA exhibits the best corrosion resistance and the corrosion rate increases when the HA content rises to more than 5 wt%. In addition, the specimen produced through the proposed method in this work indicates better corrosion resistance in comparison with cast and extruded pure Mg.     

Waves in generalized thermo-viscoelastic infinite continuum with cylindrical cavity due to three-phase-lag time-nonlocal heat transfer

Abstract

Generalized thermoelastic interactions due to three-phase-lag time-nonlocal heat transfer in a Kelvin-Voigt type infinitely extended visco-thermoelastic continuum with cylindrical cavity has been investigated. The two-temperature generalized thermoelasticity theory has also been taken into account. The problem has been solved in the domain of Laplace on the assumption that the surface of the cavity is free from traction and is subjected to a smooth and time-dependent-heating effect. Laplace inversion of the transformed solutions has been carried out numerically. The obtained numerical data for different considerations are plotted in graphs to study the effects of time-nonlocal parameter, two-temperature parameter and visco-thermoelastic relaxation parameter on different thermoelastic quantities of physical interest.     

Effect of grinding-induced cyclic heating on the hardened layer generation in the plunge grinding of a cylindrical component

This paper discusses the effects of the grinding-induced cyclic heating on the properties of the hardened layer in a plunge cylindrical grinding process on the high strength steel EN26. It was found that a multi-pass grinding brings about a uniform and continuous hardened layer along the circumference of the cylindrical workpiece. An increase of the number of grinding passes, leads to a thicker layer of hardening, a larger compressive residual stress and a deeper plastic deformation zone. Within the plastic deformation zone, the martensitic grains are refined by the thermo-mechanical loading, giving rise to a hardness of 12.5% higher than that from a conventional martensitic transformation. The coupled effects of heat accumulation and wheel wear in the multi-pass grinding are the main causes for the thickening of the hardened layer. A too small infeed per workpiece revolution would result in insufficient grinding heat, and in turn, bring about an undesirable tempered hardened layer and a reduction of its hardness.     

一种大型复杂构件加工新模式及新装备探讨

大型复杂构件是航空航天、能源、船舶等领域装备的核心结构件，此类构件通常具有尺寸大、形状复杂、刚性弱等特点。传统“分体离线加工-在线检测”模式存在工艺不稳定、过程复杂、柔性差、周期长等问题，以龙门式多轴数控机床加工为代表的“包容式”加工模式，难以适应大型复杂构件的高效高质量加工制造需求。提出一种基于移动式和吸附式机器人的多机协同原位加工新模式，通过多机器人系统自主寻位、精确定位加工与加工质量原位检测，实现大型复杂构件多安装面并行铣削、制孔与打磨等作业。多机器人系统包括移动式混联机器人、吸附式并联机器人、移动式串联铣削机器人、移动式双臂加工机器人和移动式打磨机器人。构建多机协同原位加工模式，需要揭示多机器人协同原位加工行为与大型弱刚性结构件质量控制的交互机理，面临着本体、测量、工艺和集成四个方面的挑战，需要设计高灵活、高刚度的移动式和吸附式加工机器人，解决移动机器人自主准确寻位和超大结构件原位高精检测难题，攻克加工变形误差在线补偿和振动抑制技术，通过集成实现多机协同高效高精加工，为大型复杂构件的高效高质量制造提供创新技术及装备，并实现此类构件制造核心技术及装备自主可控。     

Flame Front Deformation Instabilities of Filtration Combustion for Initial Thermal Perturbation

The flame front deformation instability of low-velocity filtration combustion within an inert packed bed is studied based on the initial preheating non-uniformity. Based on the experimental phenomena, an initial thermal perturbation model is numerically proposed so as to predict the deformation behaviors of the flame front instabilities. The numerical prediction indicates that the assumption of an initial thermal perturbation is a feasible explanation as the cause of the flame front inclination instability. As the initial thermal perturbation increases, the phenomena of the flame front break and shrinking instabilities could easily occur at high filtration velocity or low equivalence ratio. Moreover, the evolutions of the flame front break rate and the shrinking rate are quantitatively analyzed.