干腌火腿的质量缺陷及防止措施

由于猪腿原材料或者加工技术的问题,而造成干腌火腿产品质量的多种缺陷。综述了干腌火腿中常见的各种质量缺陷以及防止这些质量缺陷的措施。     

Atomic layer chemical vapour deposition of copper

Copper films with (1 1 1) texture are of crucial importance in integrated circuit interconnects. We have deposited strongly (1 1 1)-textured thin films of copper by atomic layer deposition (ALD) using [2,2,6,6-tetramethyl-3,5-heptadionato] Cu(II), Cu(thd)₂, as the precursor. The dependence of the microstructure of the films on ALD conditions, such as the number of ALD cycles and the deposition temperature was studied by X-ray diffraction, scanning electron microscopy (SEM), and transmission electron microscopy. Analysis of (1 1 1)-textured films shows the presence of twin planes in the copper grains throughout the films. SEM shows a labyrinthine structure of highly connected, large grains developing as film thickness increases. This leads to low resistivity and suggests high resistance to electromigration.     

The correlation of texture and magnetic properties in Co-Cr films

This investigation focuses on the correlation between the crystallographic orientation of grains with respect to magnetic properties in Co-Cr films. Based on a distribution measured for the (0002) crystallographic pole densities, modified formulae describing the texture were used to calculate the coercivity Hc, the squareness ratio Rs (Mr⊥/TMs) and the anisotropy field Ha for Co-Cr films. In general, calculated values for the coercive force He agreed well with the measured values. The calculated Rs⊥. values were much larger than the measured ones, however, indicating that the influence of the demagnetizing field and the magnetostriction on the orientation of the magnetization cannot be neglected. On leave from Institute of Computing Technology, Academia Sinica, P.O.Box 2704-6, Beijing, P.R. China.     

冷轧形变量对钛板材再结晶织构形成的影响

采用三维晶体学取向分布函数（ＣＯＤＦ）分析法研究了工业纯钛板材不同冷轧形变量对织构形成的影响。结果表明，冷轧形变量为５０－７０％时，再结晶退火后形成了（２１１８）（０１１０）和（１０１８）（１２１０）的部分纤维织构，而在３０％较低或８６％较高的形变量冷轧时，形成典型的轧制织构（２１１５）（０１１０）和再结晶织构（１０１３）（１２１０）型式。     

Texture Changes During the Ripening of Port Salut Argentino Cheese in 2 Sampling Zones

ABSTRACT: Texture changes during ripening of Port Salut Argentino cheese for different sampling zones were studied. Compression relaxation tests were performed and results were analyzed using both Maxwellian and Peleg's models. Elastic equilibrium modulus obtained from the Maxwellian model decreased from 1.22 to 0.11 10⁴Pa during ripening. The constants derived from Peleg's model, k₁ and k₂, diminished with ripening time from 1.18 to 0.71 min and from 1.27 to 1.12, respectively. Asymptotic equilibrium modulus from Peleg's model decreased from 0.95 to 0.07 10⁴Pa during ripening. Rate parameters derived from a 1st order kinetics applied to both equilibrium moduli showed that the decrease was faster in the external zone (0.0846 d⁻¹) than in the central zone (0.0368 d⁻¹). The correlation between equilibrium moduli, salt concentration, moisture content, and maturation indexes was obtained with a determination coefficient of 0.76.     

Molecular correlations in sheared thermotropic copolyesters showing banded textures

Banded textures produced in a thermotropic liquid crystal polymer by shearing between glass slides are examined by using both transmission electron and polarized light microscopy. The periodic variation in director orientation about the shear axis, as measured by light microscopy, is shown to be distinctly different from that indicated by electron diffraction. Measurements of birefringence and observation of Zernicke phase contrast indicate periodic variations in optical properties of the polymer, in step with the bands. Such effects are accounted for in terms of a synchronous rotation of the planar aromatic groups about the molecular chain axes. Evidence for an out-of-plane component of molecular orientation is also presented.     

The microstructure of Cu films deposited by the self-ion assisted technique

The microstructures of Cu films deposited by the self-ion assisted, partially ionized beam (PIB) deposition technique under two different accelerating potentials, 0 KeV and 6 KeV, are compared. The 6 KeV film shows a bimodal (111) fiber and (100) fiber texture with an abundance of twin boundaries and a relatively large average grain size with a typical lognormal distribution. The 0 KeV film consists of small, mostly (111) oriented grains with islands of abnormally large (100) grains. The controlling factors for the abnormal growth of the (100) grains are discussed in relation to the observed microstructures, showing that all factors necessary for abnormal (100) growth are present in the films.     

碳/碳复合材料CVI工艺中热解碳形成机理的研究

对碳碳复合材料CVI或（CVD）工艺中热碳组织的类型，沉积机理等研究情况进行了简要的综述，并对其进一步研究提出了相应观点。     

Ageing studies on some titania gels

Hydrous titania gels, precipitated from titanous chloride and aged in different aqueous media have different textural, thermal and structural properties as demonstrated by nitrogen adsorption, differential thermal analysis, X-ray diffraction and scanning electron microscopy studies. Ageing in ammonia leads to the development of microporosity, whereas ageing in water causes an extension of the pore system in the primary particles with little change in the surface texture. Heat-treatment of the precipitated gels prior to ageing seems to afford a certain stability to the primary particle by allowing hydroxo and oxo bridges to be formed, thus leading to the formation of a more rigid structure. The nature of the ageing medium and its effect on the inner coordination sphere of the titanium ions are important parameters affecting the textural and thermal behaviours of the titania gels.     

基于织疵分析与管理专家系统的探讨

为了及时分析和有效控制织物的疵点,采用VFP 6.0建立了织疵分析与管理专家系统,介绍了系统的总体结构和数据存储形式、推理机制等内容。该系统能实现各种质量指标的统计与分析,对产生率高的疵点进行产生原因的诊断、推理,得出消除疵点的方法,并能准确地确定疵点的评分。结果表明,该系统通过在某工厂的实验,疵点的推断准确率为95%以上,节省疵点的分析时间三分之二,提高下机一等品率5%~10%。