中碳结构钢件的锻造成形与锻后调质一次完成的热加工新技术

本文是利用“形变诱发析出”原理通过控制热变形成形过程获得一种能在过冷分解时使碳化物呈颗粒状弥散析出的形变奥氏体状态,又通过控制冷却抑制先共析铁素体的析出,同时促进碳化物颗粒的析出,从而得到100％调质型组织,它达到了传统工艺的水平。     

Behavioral and electrophysiological activity of (Z,E)-7,9,11-dodecatrienyl formate,a mimic of the major sex pheromone component of carob moth,Ectomyelois ceratoniae

The behavioral and electrophysiological activity of a mimic [(Z,E)7,9,11-dodecatrienyl formate] of the major sex pheromone component [(Z,E) 9,11,13-tetradecatrienal] of carob moth was assessed. Wind-tunnel bioassays demonstrated that the formate was as effective as natural gland extracts, and significantly more effective than the trienal alone or than the trienal blended with two minor pheromone components, in evoking source contact. Dispensers containing the formate were as effective as trienal-containing blend lures in attracting males when placed at the same dosage in traps in date gardens. Single-cell recordings showed that at least two olfactory neurons, differentiated by spike amplitude, are located in the long trichoid hairs on male carob moth antennae. Dose-response relationships indicated that puffs from cartridges loaded with at least 0.1 g of the formate or of the trienal were necessary to elicit spiking by either the small or the large-spiking cell within a sensillum. Cross-adaptation studies demonstrated that both compounds stimulated the same large-spiking cell. The frequencies of spikes evoked from the large cell when stimulated by emissions from 0.1-g, 1-g, or 10-g cartridges of either the formate or the trienal were not significantly different, suggesting that the formate is an effective mimic of the trienal at the antennal receptor cell level.     

Accelerated sintering of PtRh/Al2O3 catalysts in an oxygen periodic pulse flow

PtRh catalysts were prepared by coimpregnation, with chlorine-free precursors of a -alumina. They were sintered at 973 K under a continuous flow of O₂ (1% in Ar or air) or of a flow of Ar into which pulses of O₂ were injected periodically. Under the latter conditions the sintering was significantly accelerated, particularly for a certain value of the period of O₂ pulses.     

Internal-oxide-band formation during oxidation of Ag-Mg alloys

Ag-3a/oMg was oxidized in air over the range of 400–900°C. Internal-oxide bands of MgO formed approximately parallel to the surface, the first band appearing at some finite, but irregular depth below the surface. The region between the surface and the first band appeared to be free of precipitates, but TEM showed that very small clusters, about 50 Å in diameter, formed in the PFZ, causing significant hardness (greater than 300 VHN). The clusters contain more oxygen than that corresponding to stoichiometric MgO. The hardness between oxide bands was also high, but not as high as in the PFZ. The kinetics of thickening of the internal-band region followed the parabolic rate law between 400 and 700° C, with departures from the parabolic law occurring at higher temperatures. The activation energy for the parabolic rate constants was 19.4 Kcal/mol, a value less than the total for oxygen diffusion and oxygen dissolution. The reaction front was planar and parallel to the surface prior to band formation at temperatures of 400–600° C. Nucleation of the first band resulted in nonplanar and nonparallel oxide. Little or no correlation existed between grain boundaries and oxide formation. Nodules of virtually pure silver formed on the surface initially at grain boundaries and subsequently within grains. Nodule formation is attributed to stress-enhanced (resulting from strains associated with precipitation) diffusion of silver to the surface via dislocation pipes. Internal-band formation is discussed in terms of prior data in the literature and various models. It is thought that stress effects (induced by precipitation), nucleation, and clustering of oxygen with Mg play significant roles in causing internal-band formation.     

Measurement of the heat of fusion of titanium and a titanium alloy (90Ti-6Al-4V) by a microsecond-resolution transient technique

A microsecond-resolution pulse heating technique was used for the measurement of the heat of fusion of titanium and a titanium alloy (90Ti-6Al-4V). The method is based on rapid (50- to 100-s) resistive self-heating of the specimen by a high-current pulse from a capacitor discharge system and measuring, as functions of time, current through the specimen, voltage across the specimen, and radiance of the specimen. Melting of the specimen is manifested by a plateau in the measured radiance. The time integral of the net power absorbed by the specimen during melting yields the heat of fusion. The values obtained for heat of fusion were 272 J · g^–1 (13.0 kJ · mol^–1) for titanium and 286 J · g^–1 for the alloy 90Ti-6Al-4V, with an estimated maximum uncertainty of ±6% in each value.Paper presented at the Second Workshop on Subsecond Thermophysics, September 20–21, 1990, Torino, Italy.     

Why does language matter to artificial intelligence?

Artificial intelligence, conceived either as an attempt to provide models of human cognition or as the development of programs able to perform intelligent tasks, is primarily interested in theuses of language. It should be concerned, therefore, withpragmatics. But its concern with pragmatics should not be restricted to the narrow, traditional conception of pragmatics as the theory of communication (or of the social uses of language). In addition to that, AI should take into account also the mental uses of language (in reasoning, for example) and the existential dimensions of language as a determiner of the world we (and our computers) live in. In this paper, the relevance of these three branches of pragmatics-sociopragmatics, psychopragmatics, and ontopragmatics-for AI are explored.     

保持几何特征的自适应弹性二次曲线模型

物体形状特征的准确提取往往受到图像获取、目标分割等过程中各种因素的影响,因而需要构造一种鲁棒的形状表现来保有其本质特征。揭示弹性二次曲线(EQW)模型中能量权重因子和样条重叠度因子与形状几何特性间的关系,提出一种自适应保持几何特征的EQW形状表现模型,并将该模型与交互式Live Wire算法相结合,应用至图像分割中,对于各种模态图像中的目标进行分割实验。直观上,本文方法能够在去除噪声同时较好地保持目标形状的显著特征;量化结果方面,交互式分割误差保持在较小稳定范围内,引入EQW模型带来的时间开销亦在可接受范围内。     

SMA驱动丝的建模与仿真

研究SMA动力学优化模型,针对形状记忆合金(SMA)驱动丝具有强非线性、迟滞效应等特性,为设计SMA驱动丝的自适应结构,提出建立SMA驱动丝模型并提供高效的仿真方法。采用有限元软件实现了受轴向载荷的SMA驱动丝的仿真建模。对本构模型是根据自由能的一维热-力学耦合模型,可以同时复现形状记忆效应和超弹性。数值仿真能够引起材料相变的非均匀温度和应变分布。仿真结果表明,建立热-力学耦合模型,可为设计SMA驱动丝的自适应结构计算提供可靠依据。     

基于复杂网络理论的高校内部理工医文合作研究分析

运用复杂网络理论的基本原理和有关方法,对理工医文等学科、专业之间的合作规律和人员合作方式进行探讨,以某高校2005-2010年医工合作情况作为实例展开研究,采用5年的合作数据作了计算分析,研究了高校内部理工医文开展学科交叉工作的特点及其运行情况、医工交叉合作中存在问题,客观分析其原因,提出了解决的办法,为今后开展高校系统的理工医文交叉合作,建设电子化交叉平台.     

基于S7-300 PLC的运动定位系统设计

本文利用西门子组态软件WinCC及编程软件S7-300PLC实现了二维平面的快速准确定位。并对系统的平台构架、硬件选型、功能实现,实时监控做了具体的分析与设计。本系统实现了本地控制与远程监控,运行操作方式灵活可靠。自投入使用以来,各项功能正常,达到了设计要求。