塑料布"V"形铺设法在水库引冰爬坡中的应用

通过塑料布“Ｖ”形铺设法在胜利水库引冰爬坡的应用与实践，证明了此法与传统贴坡式塑料布铺设法相 比，大大削减了冰推力对坝坡的破坏，减少了坝坡的修复费用，起到了良好的效果。     

激光在塑性变形测量中的应用

本文将激光应用于云纹法，研究了缺口滚压强化后根部区域的位移场及应变分布规律。结果表明，本方法是提高塑性变形测量精度的有效手段。     

废塑料裂化生产汽柴油工业化装置研究

报道了废塑料炼油工艺中连续法、间歇法、半连续法等各种方法的特点 ;重点对各工业化流程中存在的问题和解决的方法进行了讨论 ,并提出了一些合理化的建议。     

高层钢-钢骨混凝土混合结构的设计研究

结合一幢高层钢 钢骨混凝土混合结构的设计 ,着重介绍了在罕遇地震作用下采用层模型和空间模型的弹塑性分析计算结果、钢骨混凝土柱与钢梁的计算、节点设计及相应的构造措施 ,供结构工程师参考。     

Application of material strength reserve method to the stability analysis of earth dam of feilaixia multipurpose project

The material strength reserve method is practical in the study of the stability and failure mechanism of earth dam by analysing the development of failure zone of different shear strength parameters of the earth mass of the dam. The stability in the concrete dam and ensemble architecture has got general application while analysing. In combination with Feilaixia Multipurpose Project, application of this method to earth dam stability analysis was studied by plane Finite Element Method（FEM） for the first time. Through plane FEM, we can get the failure mechanism of earth dam and appraise to the security, for operating and managing put forward some reference suggestions.     

三峡水电站充水保压蜗壳平面非线性分析

采用自编的三维钢筋混凝土非线性有限元程序，对三峡水电站充水保压蜗壳进行了平面非线性分析，分析了钢蜗壳及外围钢筋混凝土的应力变形特性。非线性计算分析表明，在蜗壳进口断面处，虽然外围混凝土较薄，但在设计内水压力、结构自重和设备重量这些荷载组合作用下，蜗壳进口断面混凝土可能不会开裂，因此钢材应力均比较低，结构具有较高的安全度。说明现有配筋方案钢筋用量可能偏多，没有充分发挥钢材的作用，在进一步设计时可以适当优化。     

Analysis of crack tip plasticity for microstructurally small cracks using crystal plasticity theory

Crack tip plastic zone sizes and crack tip opening displacements (CTOD) for stationary microstructurally small cracks are calculated using the finite element method. To simulate the plastic deformation occurring at the crack tip, a two-dimensional small strain constitutive relationship from single crystal plasticity theory is implemented in the finite element code ANSYS as a user-defined plasticity subroutine. Small cracks are modeled in both single grains and multiple grains, and different crystallographic conditions are considered. The computed plastic zone sizes and CTOD are compared with those found using conventional isotropic plasticity theory, and significant differences are observed.     

Homogeneous Plastic Flow of Fully Amorphous and Partially Crystallized Zr_(41.2)Ti_(13.8)Cu_(12.5)Ni_(10)Be_(22.5) Bulk Metallic Glass

The homogeneous plastic flow of fully amorphous and partially crystallized Zr(41.2)Ti(13.8)Cu(12.5)Ni(10)Be(22.5) bulk metallic glass (Vitl) has been investigated by compression tests at high temperatures in supercooled liquid region. Experimental results show that at sufficiently low strain rates, the supercooled liquid of the fully amorphous alloy reveals Newtonian flow with a linear relationship between the flow stress and strain rate. As the strain rate is increased, a transition from linear Newtonian to nonlinear flow is detected, which can be explained by the transition state theory. Over the entire strain rate interval investigated, however, only nonlinear flow is present in the partially crystallized alloy, and the flow stress for each strain rate is much higher. It is found that the strain rate-stress relationship for the partially crystaltized alloy at the given temperature of 646 K also obeys the sinh law derived from the transition state theory, similar to that of the initial homogeneous amo     

Analysis and optimization of weakly coupled thermoelastoplastic systems with applications to weldment design

A systematic approach for the design of weakly coupled thermoelastoplastic systems is presented. The Newton–Raphson iteration method is used in the solution process so that analytic design sensitivity formulations may be efficiently derived via the direct differentiation technique. The derived formulations are suitable for finite element implementations. Analysis and sensitivity analysis capabilities are combined with numerical optimization to form an optimum design algorithm. To demonstrate the algorithm, we optimally design a weldment with respect to manufacturing and service life aspects.