丹江口工程大坝加高后的几个水力学问题

依托1∶100水工模型试验成果,重点介绍了丹江口大坝加高后的几个水力学问题如泄流能力、坝面压力特性、河床局部冲刷、下游河道流速流态、泄洪对电厂及航运的影响等.研究显示:大坝加高后泄流能力可满足设计要求,坝下河床冲刷加重,挑距加远,设计洪水22 300 m3/s时坝下冲坑最低点高程为43.0 m,各级泄量冲坑上游坡均缓于临界坡,也略缓于初期工程同级流量冲坑的上游坡;坝下600 m以内为护岸工程重点防护段,岸边流速为5.8～9.8 m/s;泄洪对丹江口电厂影响较小,对自备电站不利影响较为显著;最大通航流量6 200 m3/s时下游引航道口门区流态复杂,水流较混乱.     

基于生态水深-流速法的河段生态需水量计算方法

在界定了生态流速和生态水深概念的基础上，提出了一种同时考虑河道本身参数(湿 周、糙率、水力坡度)和维持某一生态功能所需河流流量的水力学方法，避免了湿周法不能反映复式断面真实水位流量关系的缺点，并用于验证黄河上游小川河段生态需水量，同时用Tennant法作了对比。结果表明：用生态水深-流速法得到的小川河段生态流量优于Tennant法所计算的生态需水量，由于该方法考虑了生态流速和生态水深，故所得的结果符合实际情况。     

爆炸箔起爆系统初始电阻对爆发电流和飞片速度影响的数值模拟

研究了电爆炸箔起爆系统起爆回路初始电阻对爆发电流和冲击片雷管飞片速度的影响规律，分析了影响电爆炸箔起爆系统体系的因素，为在可靠发火条件下降低起爆系统体积提供设计参考。     

Non-Steady Equilibrium during Pro-Eutectoid Ferrite Formation in Fe-0.2C Alloy

Ｔｈｅｐｒｅｃｉｐｉｔａｔｉｏｎｏｆｐｒｏ ｅｕｔｅｃｔｏｉｄｆｅｒｒｉｔｅｆｒｏｍａｕｓｔｅｎｉｔｅｉｓｃｏｎｔｒｏｌｌｅｄｂｙｄｉｆｆｕｓｉｏｎｉｎＦｅ Ｃａｌｌｏｙｓ .Ｗｉｔｈｔｈｅａｓｓｕｍｐｔｉｏｎｔｈａｔｔｈｅｍｉｇｒａｔｉｎｇｉｎｔｅｒｆａｃｅｉｓａｌｗａｙｓｉｎｌｏｃａｌｅｑｕｉｌｉｂｒｉｕｍ ,ｅａｒｌｙｉｎ 194 9,ＺｅｎｅｒＣ[1] ｅｘｐｌａｉｎｅｄｔｈｅｄｉｆｆｕｓｉｏｎａｌｇｒｏｗｔｈｏｆｐｒｏ ｅｕｔｅｃ ｔｏｉｄｆｅｒｒｉｔｅｂｙｕｓｉｎｇｔｈｅＦｉｃｋ’ｓｌａｗ .Ｓｉｎｃｅ…     

静止浅水环境中铅垂紊动射流的试验研究

对静止均匀浅水域中的铅垂紊动射流进行了试验研究，得到了水面的隆起高度与射流出口单位能量和相对水深的函数关系，验证了隆起高度满足高斯分布，具有自相似性，并给出了统一表达式；借助于三维测速仪，得到了射流中心平面流场，结果表明射流中线流速的衰减比自由射流为快，随着射流出口流量的增加，射流出口处涡量亦增大。     

固液相变蓄能的数学模型和自然对流换热系数的实验研究

引入自然对流换热系数 ,将固液蓄能数学模型简化为仅用能量方程加以描述。并通过实验测得相变过程的实际温度场 ,证明了自然对流固液相变换热的影响不可忽略 ,验证了固液相变界面移动速率随自然对流换热系数的增大而增大的定性关系     

VTI介质中弹性参数地震反演方法

根据地震波在具有垂直对称轴的横向各向同性（VTI）介质中的运动学特征，应用传播时间反演方法，进行了水平层状VTI介质的地层弹性参数反演方法研究。在VTI介质中，P－P波的传播时间曲线不再是双曲线，尤其在长排列情况下，已不能用二项泰勒展式精确地反演P－P波的传播时间，用三项泰勒展式则可以达到更高精度；P－SV波的传播时间也可用三项泰勒展式表达，在中等及短排列长度时可达到一定精神。对P－P波、P－SV波的传播时间进行三项泰勒展开时，它们的系数中包含了地震波的各向异性信息及垂直速度信息，中以为地震波的弹性参数反演提供提供基础，模试验分析及江苏油田某地区的二维多波资料实际反演结果表明，在最大炮间距为1．5倍地层埋深时，可以很精确地得到三项泰勒展式的系数，应用这些系数能精确反演地层弹性参数，包括P波、S波的垂直速度和各向异性参数。图4表1参5（杜丽英摘）     

应用频率-初速法测试推算单桩承载力须解决的几个关键问题

本文对当前频率 -初速法应用中存在的一些问题阐述了作者的看法并着重探讨桩振初速度V0的计算方法、W0 的正确单位、如何使桩 -土体系明显震动、怎样从激振曲线中突出及分离出桩振曲线 ,从而获得正确的桩振频率f0 和首波峰 -峰值Ad、动静对比系数 βv 的选取     

Mechanical and thermal properties of HVOF sprayed Ni based alloys with carbide

The objective of the present study is to develop multi-functioned coating to the components, which are made of copper with electroplated Ni and are widely used for steel making industry. In this paper, we report the mechanical and thermal properties of Ni based superalloys with carbide sprayed by high velocity oxygen fuel (HVOF), and the detailed effects of sprayed material, spraying conditions, and initial powder structure on these properties. It was found that, among commercial Ni self-fluxing alloys (without fusing treatment), coating with a carbon content of 0.58 mass% had the most preferable properties, with a good balance of the hardness, strength, and thermal shock resistance. The thermal shock resistance depended not only on the strength of the coating but also on the volume contraction when tested at high temperatures. For the several developed Ni based superalloys with carbide, Ni20Cr8Mo5Fe–WC and Ni16Cr15Mo3–WC demonstrated the prominent adhesion strength and thermal shock resistance with high Galvanic corrosion resistance through optimized spraying condition. Also, 20 mass% NiCr–Cr₃C₂ coating sprayed by using employed relatively small primary particle succeeded in achieving the multi-superior properties; high adhesion strength, high corrosion resistance and thermal shock resistance.     

Influence of load and speed on wear characteristics of grey cast iron in dry sliding — selection for minimum wear

The wear of grey cast iron in dry sliding conditions has been studied with the aims of (1) finding the influence of working conditions on the wear rate, and (2) determining the region of speed and load where low wear is accomplished. Grey cast iron with flake and nodular graphite was submitted to investigation using a pin-on-disc machine. The results indicate that the flake graphite cast iron is more suitable for applications at speeds greater than 4 m s⁻¹ and lower loads, while nodular cast iron has greater wear resistance at lower speeds in the range of loads investigated - from 50 N cm⁻² to 200 N cm⁻²