全20CrMnTi表面激光重熔的组织与性能研究

本文对激光重熔20CrMnTi材料表明改性层显微组织分布特征、表面硬度分布规律以及残余应力状态作了研究,结果表明,表面改性层由熔融层、相变硬化层及过渡层组成,且材料表面显微硬度得到大幅度提高,表面硬度达到HV841,约提高4倍。硬化层深度约1mm。残余应力测试得出最大残余应力出现在熔凝带中心,表现为压应力。随着离中心距离的增大,残余应力逐步降低,到熔化带边缘,表现为低幅值压应力;而熔池的外边缘应力在热影响区则转变为拉应力状态。     

配送中心单品拣货模式及其效能分析

紧扣拣货作业的关键目标,介绍了8种低成本的单品拣货模式,并从生产力指标和人员配置两个方面对各种模式的效能进行了计算分析,能为配送中心拣货系统的设计和选择合适的单品拣货模式提供依据.     

喷射沉积柱状坯形状模型

通过坐标跟踪法建立了沉积坏形状预测模型。该模型不但考虑沉积坯任何表面点身自位置变化对沉积效果的影响，同时考虑了该点温度和其它表面点位置对该点沉积效果的影响，其计算过程严格按照喷射成形的实际过程执行，可实时计算并记录沉积坯的形貌，并验证了计算效果。本文模型可用于多种工艺下喷射沉积坯的形状预测。     

多模复合制导数据融合器性能评估系统方案设计

从构建多模复合制导数据融合器性能评估系统的需求出发，详细介绍了多模复合制导数据融合器性能评估系统的构建方案，并从软硬件两个方面介绍了构建这样一个系统所需要注意的问题和解决办法．     

提高供电质量减少高校供电能耗的措施

分析了高校现有供电网络存在的效率低、能耗大和供电质量不稳定的问题。提出了在增加投资不多的条件下，通过改变供电的运行方式既提高供电质量又减少能耗的一些方法。     

成形工艺对快速凝固Al—Cu—Mg合金组织和性能的影响

采用自制离心雾化装置制取了快速凝固LY12硬铝合金粉末,研究了以该粉末制成的真空热压件和挤压丝材的组织和性能。结果表明,所得粉末为泪滴状,其显微组织为树枝状晶和胞状晶。真空热压件密度高时所对应的强度高。450℃、10min、150MPa为较合理的工艺,此时粉末颗粒间结合密实,晶粒尺寸没有明显改变。在500℃热挤压时,挤压丝的组织已发生了再结晶,晶粒尺寸仍较细小。挤压丝材的抗拉强度达460MPa,其断口为韧窝状,韧窝尺寸小于3μm,且分布均匀。     

Reduction of low-frequency pressure fluctuations in wind tunnels

The determination of dynamic wind loads on buildings, i.e. pressure and deflection, has gained increasing interest (European Prestandard ENV 1991-2-4, Eurocode 1: basis of design and actions on structures—Part 2-4: actions on structures—wind actions, European Committe for Standardization, Brussels, 1995; DIN 1055 Teil 4 Lastannahmen für Bauten, Verkehrslasten, Windlasten bei nicht schwingungsanfälligen Bauwerken, 1991; N. Hölscher, M. Hortmanns, J. Sahlem, Praxisnahe Erfassung von Windwirkung an Industrie- und Hochbauten, Windwirkung im Bauwesen, Braunschweig, 7, Dreiländertagung D-A-CH 2001, Windtechnologische Gesselschaft, 2001 [1], [2] and [3]). Therefore, the spectral distributions of velocity and pressure fluctuations in wind tunnels are an important quality aspect. While velocity fluctuations can be manipulated by the obstacles used to create the turbulence, pressure fluctuations are influenced by acoustic noise as well. Especially, the first eigenfrequency of the longitudinal mode of the wind tunnel tends to disturb the pressure spectrum.In this paper, a solution for the reduction of low-frequency acoustic pressure fluctuation is presented and its application in the atmospheric boundary layer wind tunnel at the IAG is shown.     

The Problem of Estimating the Uncertainty of the Fixed Point Temperature Due to the Presence of Impurities

The main problems in estimating the uncertainty due to the presence of impurities in the material: the absence in the documents of a unique definition of the quantity being measured – the fixed point temperature, the lack of agreed methods of realizing the fixed points and the insufficient justification of the equations used for the estimate, are analyzed. The results of a measurement of the melting point of gallium are presented, which differ in the conditions in which they were realized – with one and two liquid-solid interfaces and different solidification conditions, are presented. The reasons for the considerable difference between the values of the temperatures obtained in these experiments are discussed.     

低阶煤煤层气富集模式初探

通过对美国粉河盆地以及我国铁法盆地煤层气富集规律的解剖,总结出影响低阶煤煤层气富集的关键因素是封堵,而构造、岩性和水动力是形成煤层气封堵的主要因素。同时提出了5种不同的煤层气富集模式,即背斜模式、构造—水动力模式、构造—岩性模式、岩性—水动力模式和岩性模式。     

Nd3+ Doped Silicate Glass Photonic Crystal Fiber with Random Hole Distributions

The fabrication of one kind of large core area Nd3 doped silicate glass photonic crystal fiber, and demonstration of the fiber's waveguidence properties were reported. This fiber owns a random air hole distribution in the cladding. The measured minimum loss of this kind of fiber is 10 dB·m-1 at 660 nm. These fibers can sustain only a single mode at least over wavelength ranging from 660 nm to 980 nm.