射孔孔眼中散射超声脉冲波的FEM模拟

采用有限元素法 ,分别数值计算了平底孔道、台阶式孔道和尖劈状孔道等 3种孔眼模型中不同中心频率 (10 0 k Hz、5 0 0 k Hz、1MHz)的散射超声脉冲波。计算结果表明 ,无论选用哪一种孔底模型 ,均可以得到较为明显的对应于孔底的声波信号。但是 ,孔道越不规则 ,使用的超声信号的主频越高 ,则孔底信号越差。为了兼顾孔底信号质量和信号采集、传输的代价 ,在未来的检测仪器中应采用尽可能低的测量频率 (低于 5 0 0 k Hz)     

动力载波控制接收机限幅干扰分析

通过对载波接收机限幅干扰分析 ,提出电路改进的办法。     

利用CFD获取超声流量计截面速度分布

 通过CFD技术在超声波流量计设计过程中的引入,为流量系数的获取提供了新的途径.通过对特定管道的理论计算表明,采用CFD技术获取的管道内部流型完全可以与试验数据吻合,有助于超声波流量计应用场合流量系数曲线的获取及其精度的保证.     

双跨换热器传热管在静水中阻尼特性的研究

本文对双跨换热器传热管在静水中的结构阻尼与粘滞阻尼作了简介,并对在总阻尼中占主导地位的挤压膜阻尼作了较深入的讨论。Mulcahy 于80年代初提出的挤压膜阻尼数学模型是较为完善的,其缺陷是未计入管子振幅的影响,本文对它进行了修正。为了验证理论分析的结果,笔者对双跨传热管在静水中的挤压膜阻尼作了实验研究,得出挤压膜阻尼与中间支承板厚度、管子-中间支承板间隙以及管子振幅之间的关系。     

固井声幅-变密度测井的影响因素分析

利用声幅－变密度测井进行固井质量的评价受到诸多因素的影响，各种影响因素对声幅－变密度测井资料的影响作用有较大的差异，根据大量测井资料分析和实验研究，对仪器偏心、测井时间，套管尺寸与重量，地层岩性，气侵、水泥环微间隔等因素的影响作用进行了较为深入的分析，为各种影响因素的识别与校正提出了相应的方法和依据。     

复合材料超声波直线电机的运动控制

针对复合材料超声直线电机振动体具有两个固有频率的特点，设计了具有频率跟踪特性的超声直线电机驱动器，利用激励信号频率变化改变电机运动方向，实现了超声直线电机的运动控制。     

45钢表面超音速电弧喷涂Ti-Al涂层的组织与性能研究

采用自行开发研制的超音速电弧喷设备，在45钢表面制成了钛铝合金复合涂层。并利用金相显微镜、X射线衍射仪、扫描电镜、电子探针，对涂层的成分、相结构、显微组织及其结合强度、显微硬度进行了研究。结果表明，利用超音速电弧喷涂设备，可以在45钢表面形成 度高、孔隙率低，结合强度较好和硬度高的Ti-Al合金涂层。     

A novel compact circuit for 4-PAM energy-efficient high speed interconnect data transmission and reception

Transmission of signals, whether on-chip or off-chip, places severe constraints on timing and extracts a large price in energy. New silicon device technologies, such as back-plane CMOS, provide a programmable and adaptable threshold voltage as an additional tool that can be used for low power design. We show that one particularly desirable use of this freedom is energy-efficient high-speed transmission across long interconnects using multi-valued encoding. Our multi-valued CMOS circuits take advantage of the threshold voltage control of the transistors, by using the signal-voltage-to-threshold-voltage span, in order to make area-efficient implementations of 4-PAM (pulse amplitude modulation) transceivers operating at high speed. In a comparison of a variety of published technologies, for signal transmission with interconnects of 10-15 mm length, we show up to 50% improvement in energy for on-chip signal transmission over binary encoding together with higher limits for operating speeds without a penalty in circuit noise margin.     

超声波流量计计量系统性能的主要影响因素

随着我国天然气工业的发展，已有大量超声波流量计用于高压、大流量的天然气计量。尽管我国已于2001年颁布并实施了气体超声波流量计使用方面的国家标准GB/T18604-2001，但是随着超声波流量计越来越广泛的使用，国内外对超声波流量计计量性能的影响因素已有了进一步的研究；而且，目前我国超声波流量计在天然气计量中的应用效果也还需要进一步改善。因此，根据目前国、内外最新研究成果，对噪声、脏污、压力及温度测量对超声波流量计计量系统性能的主要影响因素以及控制对策进行了分析探讨，以期改变虽经实验室检定合格、但用于现场却不能达到预期计量性能效果的情况，使超声波流量计在现场能够得到更好的应用。     

Investigation of Centreline Segregation and Centreline Porosity in CC ‐ Slabs

Improvements of solidification processing in conventional or near net shape casting depend on sophisticated methods of macroscopic examination of central unsoundness and inhomogeneity of the cast material. As long as remarkable deviations referring to the quality features exist between the slab centre and the bulk material such methods should be looked after. Two semi‐macroscopic methods of segregation analysis are discussed in this paper: firstly, the potential of the emission spectral analysis combined with sectioning of a sample and secondly, the computer aided micro‐probe analysis. Both methods are restricted to small local areas. The proneness of elements and steel grades with respect to micro‐ and macrosegregation as well as distribution‐ and segregation coefficients are determined. The effect of a diffusion anneal on homogenisation of segregation is studied. Last not least the precipitation of sulphides, phosphides or carbonitrides is estimated. Ultrasonic detection of the central unsoundness of conventional slabs or thin slabs is a new approach towards a quantitative macroscopic examination. The sample size is 400 mm x 300 mm x 30 mm. To achieve a low ultrasonic noise using a 5 MHz‐transducer the samples are heat treated for grain refinement. “Dog bone porosity”, macroscopic topographical misfit between the upper and lower solidifying shells, periodical corner cracks or systematic transverse centre cracks are detected. Obviously, segregations do not reflect the ultrasonic beam. However, it can be presumed that an interrelation exists between porosity and segregation, although these might be locally apart from each other. This new ultrasonic test of the central unsoundness of continuous cast (c.c.) slabs gives valuable arguments to machine builders and maintenance people to decide on the right concepts for strand guidance, support rollers and secondary cooling. Soft reduction can be optimized and variations in casting speed counteracted by dynamic means. R&D service of this kind can help steelmakers when decisions are impending to build new casting machines or revamp old ones.