关于起重机接地形式的现场检验

由于对低压电力网接地形式理解上的异议，长时间以来在起重机接地的检验中把握尺度不同，作为起重机械现场检验的重要项目，检验结论必须严谨准确、果断周细。     

高硬度耐磨电弧喷涂管状丝材的研究

利用自熔性合金与非晶态材料的特点，研制了Fe—B系管状丝材作为电弧喷涂材料，其形成的涂层具有良好的结合强度、低的孔隙率、高的硬度和耐磨损性能。     

基于切削振动相关性识别刀具磨损状态的模型与实验

本文提出基于切削振动相关性识别刀具磨损状态的研究思想,建立了车削中刀杆双向横振动系统及其单输入双输出系统的数学模型。理论和实验均表明,刀杆双向横振动之加速度响应在固有基频处的相干函数与刀具磨损状态之间有很好的规律性,它反映了两者之间的本质机理,并提供了识别刀具磨损状态的新途径。     

Synthesis of diamond crystals and films using an oxygen-acetylene flame under atmosheric pressure

Diamond growth with rates up to 100 to 140 μm/hr was achieved using an oxygen-acetylene combustion spraying technique in an atmospheric environment. Investigations on the processing indicated that the gas flow ratio, substrate position, substrate temperature, temperature distribution, and substrate pretreatment were the most important factors affecting the growth of diamond crystals. Evaluation by means of X-ray diffraction, Raman spectroscopy, scanning electron microscopy, and electron probe microanalysis showed that the synthesized diamond was nearly perfect in morphology, structure, and purity.     

Effect of partitioning on microstructure and properties of a medium carbon Ti Mo bearing high strength Q&P steel

In order to investigate the effect of partitioning procedures on microstructure and properties of a medium carbon Ti Mo bearing steel, the salt bath experiment, field emission SEM, TEM and tensile tests as well as wear tests were utilized to clarify the microstructural evolution and property changes treated by different partitioning parameters. The results show that the microstructures consist of tempered lath martensite, cementite and (Ti, Mo)C particles. With prolonging partitioning time or increasing partitioning temperature, the amount of laths martensite decreases and thicker martensite plates with blunt boundaries appear. In addition, with increasing partitioning temperature from 310℃ to 400℃, the tensile strength, hardness and low temperature toughness are simultaneously decreased, and the reduction reaches up to about 300MPa, 100HV and 20J, respectively. Finally, the wear performance of the samples partitioned below Ms is obviously better than that of samples partitioned above Ms. The morphology of worn surface of samples partitioned below Ms is characterized by plastic fatigue morphology, while the worn surfaces of samples partitioned above Ms are mainly dominated by grooves.     

柱体自由扭转时的最优横截面形式

当柱体自由扭转时，柱体的抗扭性能与横截面形式有关，针对单连通域下的具有最优抗扭性能的横截面形式问题，本文建立了相应的最优形式控制模型，并通过变分法求解得到：在横截面面积相等的情况下，圆截面是所有截面中使结构整体应变能最小和扭转刚度最大的截面形式，这与圣维南所给的一般性结论是一致的。     

Stepwise-Graded Si3N4–SiC Ceramics with Improved Wear Properties

The processing of stepwise graded Si₃N₄/SiC ceramics by pressureless co-sintering is described. Here, SiC (high elastic modulus, high thermal expansion coefficient) forms the substrate and Si₃N₄ (low elastic modulus, low thermal expansion coefficient) forms the top contact surface, with a stepwise gradient in composition existing between the two over a depth of ∼1.7 mm. The resulting Si₃N₄ contact surface is fine-grained and dense, and it contains only 2 vol% yttrium aluminum garnet (YAG) additive. This graded ceramic shows resistance to cone-crack formation under Hertzian indentation, which is attributed to a combined effect of the elastic-modulus gradient and the compressive thermal-expansion-mismatch residual stress present at the contact surface. The presence of the residual stress is corroborated and quantified using Vickers indentation tests. The graded ceramic also possesses wear properties that are significantly improved compared with dense, monolithic Si₃N₄ containing 2 vol% YAG additive. The improved wear resistance is attributed solely to the large compressive stress present at the contact surface. A modification of the simple wear model by Lawn and co-workers is used to rationalize the wear results. Results from this work clearly show that the introduction of surface compressive residual stresses can significantly improve the wear resistance of polycrystalline ceramics, which may have important implications for the design of contact-damage-resistant ceramics.     

基于过程能力指数的刀具寿命研究

利用Glejser检验方法拟舍出刀具磨损过程残差模型，在此基础上，计算换刀时刻的过程能力指数，并且根据企业所要求的最低过程能力指数，计算刀具的质量寿命，提出将刀具的切削寿命和质量寿命结合起来进行换刀决策的方法。     

铁谱技术在判断发动机磨损状态中的应用研究

发动机中各摩擦副的工作环境恶劣，磨拟状态复杂，很难精确描述。而发动机所处的磨损状态是判断其是否正常工作的重要标准，因此建立发动机磨损状态监测具有重大的经济和社会效益。笔者利用铁谱技术作为一种监测手段，通过磨粒分析来判断发动机的磨损状态。