治理铬渣的两个关键

铬渣中存在的酸溶性六价铬是解毒效果能否持久的关键，而铬渣中游离氧化镁消化是利用铬渣作建筑材料时必须高度重视的问题，论述了湿法解毒、高温解毒和非熔融的综合利用法等方法，对铬盐行业的铬渣治理有指导作用。     

Environmental etch performance, and scratch and mar of automotive clearcoats

Environmental etch damage to automotive coatings, and scratch and mar of these coatings are an important element of customer satisfaction as well as a significant warranty repair consideration for automotive companies. The conditions that result in environmental etch are examined and a laboratory test proposed. Data from this test are compared to automotive hoods exposed in Florida. The performance of various crosslinking chemistries is discussed and the requirements for improved environmental etch are outlined. Scratch and mar performance of these systems is also reviewed. We have found that coatings respond to physical stress by elastic recovery, by plastic flow and by brittle fracture. Classifying types of damage in this way is important for understanding the chemistry needed for improved scratch and mar of coatings.     

湿式氧化处理乙烯裂解废碱液

文章研究了WAO处理乙烯裂解废碱液的方法。在2L高压釜中进行了乙烯废碱液的湿式氧化实验研究，重点考察了反应温度、停留时间对乙烯废碱液中COD、S^2-,酚的含量的影响。结果表明，湿式氧化处理乙烯裂解废碱液是可行的，处理后污水中COD、S^2-,酚的去除率分别达到40％、98％和30％，达到了排放标准。     

催化湿式氧化法处理焦化废水的分析

概述了焦化废水水量大、成分复杂、污染物浓度高等水质特点和传统焦化废水处理方法及其缺陷，提出应用催化湿式氧化技术处理焦化废水这一新途径。并就技术和经济方面对催化湿式氧化技术处理焦化废水进行了分析，说明利用该技术处理焦化废水不仅技术上可行而且具有较好的综合效益。指出了催化湿式氧化技术在工业化过程中面临催化剂溶出和反应设备材质要求高等问题。     

湿法制造热塑性片材的工艺技术研究Ⅰ.热塑性片材概论

本文介绍了玻璃纤维毡增强热塑性片材（GMT）的特点，分类及制造工艺；阐述了湿法即介质悬浮法制造热塑性片材的工艺流程及专用设备。     

废碱液湿式氧化处理装置控制系统的设计及应用

介绍了废碱液湿式氧化处理装置工艺流程及控制方案,分别阐述了上位机和下位机的硬件构成和软件设计方法.文中介绍的方法可为同类装置的控制系统提供可靠的参考.     

湿法成型中稳定浆料的制备

为了满足各工业领域对陶瓷材料的需求,人们开发和研制多种适合成型复杂形状的湿法成型技术,湿法成型中最关键的一步是稳定浆料的制备。本文从稳定浆料的制备条件,形成稳定浆料的理论依据以及稳定浆料所具备的流变特性等几个方面,对湿法成型中浆料的制备进行了综述。     

Electrochromic WO3−x films with reduced lattice deformation stress and fast response time

Electrochromic properties of electrochemically deposited and etched (EDE) WO_3−x films have been investigated using voltammetry and nanogravimetry to elucidate the amount of residual stress associated with lattice polarization and deformation in WO_3−x nanoparticles. The cathodic WO_3−x deposition from pertungstic acid solution and unusual properties of the cathodic electroetching of the oxide in tetraethyl ammonium chloride solution are reported and elucidated on the basis of Electrochemical Quartz Crystal Nanogravimetry (EQCN) measurements. The stress enhanced resonant frequency shift was observed upon WO_3−x film coloration. However, the stress enhancement appeared to be much lower (up to 4-6 times) than that measured for films synthesized by other methods. The stress reduction in WO_3−x films under study has been attributed to the stress relaxing propensity of EDE film to suppress the compressive stress wave. A considerable isotopic effect has been observed in nanogravimetry of the H⁺ and D⁺ ion intercalation into WO_3−x films. We have found that the isotopic effect is primarily due to the true mass loading difference between hydrogen and deuterium ions, for the same concentration of color centers (2.65 × 10²¹ cm⁻³), since EQCN frequency shifts associated with stress in the film for H⁺ and D⁺ are very close to each other.     

Homogeneous versus heterogeneous catalytic reactions to eliminate organics from waste water using H2O2

Homogeneous (Cu²⁺ ions) and heterogeneous (Cu²⁺-pillared clay) Fenton-like catalysts have been compared in the conversion of p-coumaric acid. The performances of the two classes of catalysts are similar for an analogous amount of copper, but there are some relevant differences in terms of (i) the presence of an induction time, (ii) the turnover frequency, (iii) the efficiency in the use of H₂O₂, (iv) the initial attack of p-coumaric acid (hydroxylation on the aromatic ring or oxidative attack on the double bond of the lateral chain), and (v) the effect of dissolved oxygen on the removal of total organic carbon (TOC). These differences were interpreted in terms of reaction network of generation of radical oxygen species and of organics conversion. The possible formation of a surface peroxo adduct coordinated to a copper binulcear site was also evidenced for the solid heterogeneous catalyst.     

不同木质素磺酸钠对豆粕胶黏剂性能的影响

通过FTIR、元素分析、GPC对4种不同来源的木质素磺酸钠进行物理化学性质分析,并将其与水性聚酰胺协同改性豆粕胶黏剂(简称豆粕胶),利用测试接触角、剪切黏度和湿态胶合强度考察改性前后胶黏剂的浸润性、流变特性以及所得胶合板的胶合性能.红外谱图分析表明,在1065 cm–1附近出现了磺酸基或磺甲基中S==O的伸缩振动吸收峰,证明木质素经过磺化反应或磺甲基化反应得到木质素磺酸钠;木质素磺酸钠中磺酸基含量越高,经其改性的豆粕胶的零剪切黏度越低且在木材表面的润湿性越好;豆粕胶黏剂与杨木单板的接触角从未改性的95°降到改性后的61°;与水性聚酰胺协同改性后的豆粕胶制得胶合板的湿态胶合强度达到0.92 MPa,合格率为100％,满足国家Ⅱ类胶合板的标准要求(胶合强度≥0.70 MPa,合格率≥90％).