Talbot效应研究新进展

综述了对Ｔａｌｂｏｔ效应研究的进展，着重介绍了对它的新解释。     

10W QCW operation of a proton implanted GaAlAs diode laser array

We report one thick layer of hard-baked photoresist mask.The laser array stripe pattern was defined by standard wet lithography.With this mask, a 10 W QCW(quasi-continuous wave) operation of a narrow proton implanted multiple stripe conventional single quantum well separate confinement heterostructure(SQW-SCH) GaAlAs diode laser array has been realized.These devices exhibit the lateral far-field radiation pattern of a phase-locked array of gain-guided semiconductor injection laser array. The twenty stripe laser array has a lateral far-field beam divergence full width at half maximum (FWHM) of less than 3°, and three twenty stripe laser array has a beam divergence in the plane of the junction of about 9°.     

水下成像的现状和发展动向

本文以下水成像在军事，海洋开发工程应用为基础，论述了水下观测和成像中采用微光电视摄像机和激光器件及其系统的技术现状和发展动向。     

Toward in-situ flaw detection in laser powder bed fusion additive manufacturing through layerwise imagery and machine learning

Process monitoring in additive manufacturing may allow components to be certified cheaply and rapidly and opens the possibility of healing defects, if detected. Here, neural networks (NNs) and convolutional neural networks (CNNs) are trained to detect flaws in layerwise images of a build, using labeled XCT data as a ground truth. Multiple images were recorded after each layer before and after recoating with various lighting conditions. Classifying networks were given a single image or multiple images of various lighting conditions for training and testing. CNNs demonstrated significantly better performance than NNs across all tasks. Furthermore, CNNs demonstrated improved generalizability, i.e., the ability to generalize to more diverse data than either the training or validation data sets. Specifically, CNNs trained on high-resolution layerwise images from one build showed minimal loss in performance when applied to data from an independent build, whereas the performance of the NNs degraded significantly. CNN accuracy was also demonstrated to be a function of flaw size, suggesting that smaller flaws may be produced by mechanisms that do not alter the surface morphology of the build plate. CNNs demonstrated accuracies of 93.5 % on large (>200 μm) flaws when testing and training on components from the same build and accuracies of 87.3 % when testing on a previously unseen build. Finally, evidence linking the formation of large lack-of-fusion defects to the presence of process ejecta is presented.     

封闭循环TEA CO2激光器用催化剂的实验研究

在不同的催化剂和不同温度的条件下,用磁氧分析仪监测了封离型TEA C0₂激光器中O₂含量随时间或脉冲次数的变化。对实验现象进行了分析。对几种催化剂的特性给出了详细的比较。     

The development of a high-speed spindle measurement system using a laser diode and a quadrants sensor

Reducing the manufacturing time is the trend of precision manufacturing, and the precision of a work-piece is very important for manufacturing industry. High-speed cutting is becoming more widely used and the high-speed spindle is a very important element, whose precision may affect the overall performance of high-speed cutting. Most of the studies on high-speed cutting are focused on the cutting force, the vibration of the spindle and the effects of the spindle's thermal expansion; however, the measurement of the high-speed spindle continues to use the conventional spindle measurement method.As with the measurement of the high-speed spindle, more strict demands are set on the dynamic balance of cutting tools and the bandwidth of the measurement systems when compared with common spindles. The capacitance displacement sensor has been employed for the spindle error test. The precision of the measurement system is limited by the reference (such as a master ball or a master cylinder). Also the capacitance sensor and the reference must be grounded together. This paper presents a simple spindle measurement system using a laser diode and a quadrants sensor, with accuracy up to 1 μm, within 300,000 rpm for various spindles. The system does not need any reference and it is easy to set up. This system can be applied to measure the spindle errors, the spindle speed and the spindle indexing.     

Formation of WC/Ni hard alloy coating by laser cladding of W/C/Ni pure element powder blend

WC/Ni coating was formed by laser cladding of a W/C/Ni powder blend. The formed WC crystals have rectangular or quadrangle cross-section shapes with size of 2–30 μm. Step, twist and cross growth morphologies of WC formation were observed. The coating contains WC, CW_3, WNi, FeW₃C, Fe₆W₆C, W₃O, W, C, and (Fe,Ni) phases.     

Laser Dressing of Metal Bonded Diamond Wheel

In this study, a laser beam is used as a non-contact thermal dressing tool for a bronze bonded diamond wheel. The pulsed-Nd:YAG laser beam is irradiated on the wheel surface and the bond material partially removed by laser irradiation only. In order to efficiently remove the bond material, it is necessary to direct an air jet on the spot irradiated by the laser so as to blow away the molten binder before it solidifies again. Less damage of diamond particles such as micro-cracks or graphitization occurs. In grinding with a laser-dressed wheel, the grinding forces are almost the same as those for a conventionally dressed wheel. Consequently, effective laser dressing can be expected with the associated dressing conditions.     

Mapping and Modelling Single Scan Track Formation in Direct Metal Selective Laser Melting

When a laser beam scans the surface of a metallic powder bed, the resulting track may be continuous with a crescent shape cross-section, continuous with an elliptical section, discontinuously irregularly broken, discontinuously balled or only partially melted. This paper reports experimental observations of what CO₂laser powers and scan speeds lead to what type of track, for M2 and H13 tools steels and 314S stainless steel powder beds. It also presents measurements of bed physical properties relevant to predicting the behaviour and the results of modelling that agree with the experiments. The results are placed in the broader context of selective laser melting build strategies     

镁合金表面激光电弧复合熔覆 5556 铝合金工艺研究

铝合金熔覆是轻量化镁合金表面涂层防护的重要方法。 本研究使用 AZ80A 镁合金作为基材, 使用 5556 铝 合金作为熔覆合金, 并使用激光电弧复合熔覆进行了铝合金熔覆层制备。 对熔覆层组织进行了分析, 重点研究了 激光摆动对熔覆层品质的影响。 结果表明, 当激光无摆动时, 熔覆层宽度有限, 无法正常形成各道次熔覆层的有 效搭接, 且缺陷较多。 在增加激光摆幅的情况下, 激光加热能量会更均匀地在镁合金基材表面分散, 有效增加了 熔宽, 提升了各道次熔覆层的搭接率, 促进内部缺陷更少、 品质更高的连续熔覆层的形成。