Modelling dislocation assisted tempering during rolling contact fatigue in bearing steels

Rolling contact fatigue in bearing steels is manifested by dark-etching regions, which are attributed to deformation induced tempering. In order to quantitatively explain this phenomenon, a model is suggested for martensite tempering assisted by dislocation glide during rolling contact fatigue. In the model, dislocations transport carbon from the matrix to carbide particles, provided that the carbon is located at a certain distance range from the dislocation contributing to the tempering process. By calculating the amount of carbon in the matrix, the kinetics of carbide thickening and hardness reduction are computed. It is found that the dark-etching region kinetics can be controlled by both bearing operation conditions (temperature and deformation rate) and microstructure (type, size, and volume fraction of carbides). The model is validated against tested bearings, and its limitations are discussed.     

Simulation of thermal barrier coating spallation induced by the initiation/growth/coalescence of internal crack and interfacial crack based on a real image model

In the furnace cycle test, the growth of oxide film leads to the propagation and coalescence of multiple cracks near the interface, which should be responsible for the spallation of thermal barrier coatings (TBCs). A TBC model with real interface morphology is created, and the near-interface large pore is retained. The purpose of this work is to clarify the mechanism of TBC spallation caused by successive initiation, propagation, and linkage of cracks near the interface during thermal cycle. The dynamic growth of thermally grown oxide (TGO) is carried out by applying a stress-free strain. The crack nucleation and arbitrary path propagation in YSZ and TGO are simulated by the extended finite element method (XFEM). The debonding along the YSZ/TGO/BC interface is evaluated using a surface-based cohesive behavior. The large-scale pore in YSZ near the interface can initiate a new crack. The ceramic crack can propagate to the YSZ/TGO interface, which will accelerate the interfacial damage and debonding. For the TGO/BC interface, the normal compressive stress and small shear stress at the valley hinder the further crack propagation. The growth of YSZ crack and the formation of through-TGO crack are the main causes of TBC delamination. The accelerated BC oxidation increases the lateral growth strain of TGO, which will promote crack propagation and coalescence. The optimization design proposed in this work can provide another option for developing TBC with high durability.     

Damage mechanism at different transpassive potentials of solution-annealed 316 and 316l stainless steels

Electrochemical impedance spectroscopy (EIS), anodic polarization and scanning electron microscopy techniques were used to investigate the damage mechanism in the transpassive potential region of AISI ...     

氧化石墨烯改性碳纤维复合材料抗冲击行为研究

使用单层纳米氧化石墨烯（NGO）粒子对环氧树脂进行改性处理，采用真空辅助树脂传递模塑成型工艺制备了[±45/0/90]_2S铺层角度下的纯树脂及单层NGO改性碳纤维复合材料（CFRP）层合板。通过落锤冲击试验、超声C扫描检测、冲击后压缩试验等对纯树脂及单层NGO改性CFRP进行实验研究。结果表明，纯树脂及单层NGO改性CFRP在损伤阻抗及损伤容限实验中均存在拐点现象，且拐点出现在相同深度位置，其中纯树脂CFRP拐点位置为0.51 mm，单层NGO改性CFRP拐点位置为0.43 mm；相对于纯树脂CFRP，单层NGO改性CFRP可以显著提高复合材料的抗冲击性能及冲击后的压缩性能；通过对冲击后凹坑深度及凹坑面积进行数据模拟，可以用拟合公式实现对复合材料的损伤预测。     

CO2驱沥青质沉积对致密储层的伤害机理——以鄂尔多斯盆地延长组长8储层为例

为了揭示CO2驱替过程中沥青质沉积对致密储层的伤害机理,文中基于岩心核磁共振T2谱测试原理,开展了CO2注入压力下的岩心驱替实验,研究了沥青质在岩心中的沉积特征,评价了沥青质沉积对储层的伤害程度。实验结果表明:沥青质沉积量和渗透率伤害率随着CO2注入压力的升高呈现先快速上升后趋于平缓的趋势;在CO2注入过程中,沥青质主要沉积在弛豫时间大于10 ms的大、中孔隙,导致大、中孔隙占比下降,微细、小孔隙占比增加,且随着CO2注入压力的升高,大、中孔隙占比下降幅度增大,微细、小孔隙占比上升幅度增大;此外,沥青质沉积会引起润湿性发生反转,随着沥青质沉积量的增加,润湿反转指数增大,岩心润湿性不断向强油湿方向转变。     

Ballistic behavior of plain and reinforced concrete slabs under high velocity impact

This work presents a numerical simulation of ballistic penetration and high velocity impact behavior of plain and reinforced concrete slabs. In this paper, we focus on the comparison of the performance of the plain and reinforced concrete slabs of unconfined compressive strength 41 MPa under ballistic impact. The concrete slab has dimensions of 675 mm × 675 mm × 200 mm, and is meshed with 8-node hexahedron solid elements in the impact and outer zones. The ogive-nosed projectile is considered as rigid element that has a mass of 0.386 kg and a length of 152 mm. The applied velocities vary between 540 and 731 m/s. 6 mm of steel reinforcement bars were used in the reinforced concrete slabs. The constitutive material modeling of the concrete and steel reinforcement bars was performed using the Johnson-Holmquist-2 damage and the Johnson-Cook plasticity material models, respectively. The analysis was conducted using the commercial finite element package Abaqus/Explicit. Damage diameters and residual velocities obtained by the numerical model were compared with the experimental results and effect of steel reinforcement and projectile diameter were studies. The validation showed good agreement between the numerical and experimental results. The added steel reinforcements to the concrete samples were found efficient in terms of ballistic resistance comparing to the plain concrete sample.     

氧气底吹熔炼氧枪浅析

系统地论述了氧气底吹熔炼氧枪的结构、工作原理、设计计算方法、材质及蚀损机理．指出了延长氧枪使用寿命的措施。     

双河油田注入水适应性及注水井酸化解堵研究

考察了双河油田双河联、江河联注入水堵塞地层的因素;膨胀性黏土，悬浮固体颗粒。细菌及悬浮污油。含膨胀性黏土的双河南、双河北及不含膨胀性黏土的双江岩心粉，在注入水中相对于地层水中的体积膨胀度分别为14．5％、11．1％及0．02％；注入100PV不含悬浮颗粒的等体积比地层水、注入水混合水使双河、双江岩心渗透率分别下降7％和4％、9％和7％。注入水中悬浮颗粒引起岩心渗透率下降，粒径越大、颗粒浓度越大、注入量越大，则渗透率越低。在粒径2．1μm或颗粒浓度3mg／L前后下降幅度变化较大。注入水中硫酸盐还原菌引起岩心渗透率下降，含菌量越大则渗透率开始下降时的注水量越小，注入含菌50个／L的水100PV使岩心渗透率下降7％。岩心对注水合油量敏感，注入含油量20mg／L的水50PV使岩心渗透率下降20％。在岩心注水实验中渗透率下降最严重的是双河南岩心，其次是双河北岩心．江河岩心较轻，注入精细过滤水的双河北岩心渗透率下降大大减少．说明悬浮固体是造成注水堵塞的主要因素。为了解除双河油田注水井的堵塞，研制了含黏土稳定剂、缓蚀剂、铁离子稳定剂、互溶剂的土酸液，与南阳油田使用的低伤害酸液一起，用于1口注水井的解堵，效果良好。图7表4参5。     

污染地层渗透率分布特征研究

关于悬浮物固相侵入造成的地层伤害，研究人员做了大量的工作，并在文献上发表了一些模型的建立方法。但是没有对地层中渗透率的具体情况作详细研究。文中介绍了一个以颗粒通过多孔介质的物质平衡为基础的数学模型，采用有限差分法求解，编制计算机软件，将渗透率在不同污染距离和时间的结果描绘出来，并作了一些详细研究。这对研究污染状况和后面要采取的酸化等解堵措施提供了更好的条件。     

非渗透抗压钻井液处理剂KSY的研究与应用

非渗透抗压钻井液技术是解决钻进压力衰竭地层、裂缝发育地层、破碎或弱胶结性地层、低渗储层及深井长裸眼大段复杂泥页岩和多套压力层系等地层的压差卡钻、钻井液漏失和井壁垮塌等复杂问题以及油气层损害问题的关键技术，其核心是非渗透抗压处理剂。研制开发了非渗透抗压处理剂KSY，并进行了钻井液性能评价和泥饼结构分析，结果表明，KSY加入钻井液后，对钻井液流变性影响小，滤失量明显降低，形成的封堵膜薄，易于返排，封堵强度高，能够有效提高地层的承压能力和破裂压力，保护油气层效果好。现场应用表明，KSY能够显著提高地层承压能力，防止井壁坍塌，保持井径规则，有利于固井和完井作业。