Net shape formation of sub-micron alumina with reduced flaws by high-speed centrifugal compaction process

A new compacting method for powder materials is presented. High-Speed Centrifugal Compaction Process (HCP) utilizes centrifugal force of about 10,000 g for the compaction. HCP is suitable for net shape compaction of fine sub-micron and nano-powders. HCP possesses a unique compacting mechanism that is different from other colloidal processes including Pressure Casting (PC), and has a number of useful characteristics. HCP has a higher compacting speed than PC, wide applicability for net shape formation, as well as a defect removing function. Because of homogeneous and flawless green microstructure, HCP alumina shows superior sinterability and higher strength and hardness than most of other aluminas. This article is based on a presentation made in the symposium “The 3rd KIM-JIM Joint Symposium on Advanced Powder Materials“, held at Korea University, Seoul, Korea, October 26–27, 2001 under auspices of The Korean Institute of Metals and Materials and The Japan Institute of Metals.     

机床的静压系统及润滑

对机床的静压系统及其发展过程进行了综述 ,介绍了静压系统的基本结构、特点及其在机床中的各种运用。     

实用M2052合金阻尼行为表征

名义组分为Mn-20Cu-5Ni-2Fe(原子分数，％)的M2052合金，具有很高的强度和阻尼性能．对该合金在不同条件下的阻尼性能采用多种方法进行了表征．该合金的高阻尼态出现在一个临界温度以下，该温度可以通过改变组分和热处理来调整．合金的室温阻尼性能强烈地依赖于频率、应变振幅以及静载荷的大小．     

车床静刚度计算机测试系统研制

在分析了车床的结构特点和车削工艺系统的受力情况和借鉴传统车床静刚度仪优点的基础上，研制了一套基于计算机控制的车床静刚度测试系统。系统由计算机作为信号检测、数据处理和控制核心，并配以精密位移传感器、压力传感器和步进电机及其驱动器等。实现了自动加载、卸载，采样，数据处理，直接绘制、显示和打印刚度曲线等功能。系统的成功研制为车床静刚度的测试提供了一种先进手段。实测结果表明，该系统具有自动化程度高、测试效率高、精度高、可靠性高、测试性能稳定的优点。     

Quantitation of volatile compounds in heated triolein by static headspace capillary gas chromatography/infrared spectroscopy-mass spectrometry

Static headspace and capillary gas chromatography/infrared spectroscopy-mass spectrometry were used to collect, separate, identify and quantitate the oxidative and thermal decomposition products in heated triolein. Approximately 4 L of triolein was heated in a deep-fat fryer at 190°C for 12 h each day for a total of 60 h, until it contained>-20% polymeric material. The concentration of heptane and octane increased after 12 h heating, then decreased upon further heating, while the concentration of volatile aldehydes decreased gradually during heating. After 12 h of heating, the concentrations of the major volatiles changed as follows: heptane (16.36 to 30.17 ppm), octane (24.48 to 40.77 ppm), heptanal (21.68 ppm to 9.11 ppm), octanal (35.53 to 36.64 ppm), nonanal (68.95 to 43.16 ppm), (E)-2-decenal (135.00 to 89.00 ppm) and (E)-2-undecenal (88.50 to 61.00 ppm). After 60 h of heating, when the oil contained over 20% polymeric material, the concentrations of heptane, octane, heptanal, octanol, nonanal, (E)-2-decenal and (E)-2-undecenal were 5.16, 4.39, 5.45, 7.02, 18.07, 12.50 and 6.00 ppm, respectively.     

Torque Transmission Capabilities of Bonded Polygonal Lap Joints for Carbon Fiber Epoxy Composites

Although carbon fiber epoxy composite materials have excellent properties for structures, the joint in composite materials often reduces the efficiency of the composite structure because the joint is often the weakest area in the composite structure.

In this paper, the effects of the adhesive thickness and the adherend surface roughness on the static and fatigue strengths of adhesively-bonded tubular polygonal lap joints have been investigated by experimental methods. The dependencies of the static and fatigue strengths on the stacking sequences of the composite adherends were observed.

From the experimental investigations, it was found that the fatigue strength of the circular adhesively-bounded joints was quite dependent on the surface roughness of the adherends and that polygonal adhesively-bonded joints had better fatigue strength characteristics than circular adhesively-bonded joints.     

陶瓷材料断裂韧性测试新技术：静态爆破剂预制裂纹的研究

准确测试陶瓷材料断裂韧性Ｋ１Ｃ的关键是预制具有原生裂纹的试样。本文以单边切口梁法测试Ｋ１Ｃ为基础，提出了一种简便而有效的陶瓷材料原生裂纹的预制方法－静态膨胀法。研究结果表明：静态膨胀法中裂纹的扩展是稳态的；通过调节影响微裂纹产生与扩展的多种因素，可以准确地控制裂纹扩展的深度，预制出合适的原生裂纹，为准确评价结构陶瓷的断裂韧性提供了一种有效可行的方法。     

锌系工件的静电粉末涂装和工艺管理

讨论了锌系工件喷涂的相关工艺、现场管理、技术参数、质量检验和环境要求等。     

导静电乳液胶粘剂的研制

用多元乳液共聚法制备了用于粘贴导静电PVC地板胶粘剂,加入乙炔碳黑赋予乳液胶粘剂导静电性能。研究了影响胶接强度和初粘力的主要因素,确定m(VAc)/m(BA+VAc)较合适比为1∶3;研究了乳化剂和交联单体对乳液性能的影响,研究得出,适量加入AA和HMAM可以减少乳化剂的用量,提高乳液的性能;考查了影响导静电性能的因素,研究表明,导静电性能由乙炔碳黑决定,其加入量越大,导静电性能越好。得到的导静电乳液胶粘剂胶接强度达到0.51MPa以上,导静电可达到7.2×103Ω,两项指标均超过国家标准。     

动态水力旋流技术发展综述

介绍了动态水力旋流器的结构、操作原理及国内外发展概况,对比分析了动态水力旋流器与静态水力旋流器在处理含油污水方面的不同利弊,总结了动态水力旋流器的主要结构特性、操作特性及分离性能,并归纳了动态水力旋流技术在应用中的一些研究结论。