含损伤软化材料层合板承压时的分叉分析

本文讨论了由纤维和树脂-损伤应变软化材料组成的层合板在面内受压时的压缩分叉。用有限变开理论和半解析有限元法建立了相应的分叉方程,并进行数值模拟。计算结果表明,分叉将在损伤材料的应变软化阶段发生,为剪切带形分叉,损伤材料骨有剪应变集中,而且在纤维和树脂的界面附近有较大的剪应变突变等现象。     

Mechanoluminescent pulse pressure sensors. Processing of output optical signal

The process of mechanoluminescence transformation of a pulse pressure sensor is considered. The process consists in excitation of emission under the action of mechanical loading. An algorithm for use in processing the output optical signal of the sensor that makes it possible to determine an input shock pulse is presented. __________ Translated from Izmeritel’naya Tekhnika, No. 10, pp. 28–31, October, 2007.     

基桩反射波法动测曲线的数值模拟与特征分析

采用美国PDI公司开发的PDI-S软件,对不同缺陷基桩的反射波法低应变动测曲线进行数值模拟,对动测曲线的特征进行归纳与总结,以便在解释反射波法曲线时作为参考与借鉴,提高基桩质量检测的可靠度。     

钛合金的银脆,镉脆敏感性及其控制

利用慢应变速率拉伸技术（ＳＳＲＴ），并结合恒载实验，较全面地研究了Ｔｉ－６Ａｌ－４Ｖ合金的银脆行为、固态与液态镉脆行为，确定了应变速率、接触条件、热处理制度、试样取向、温度等因素对Ｔｉ－６Ａｌ－４Ｖ合金银脆与镉脆敏感性的影响，探讨了Ｎｉ阻挡层对控制Ｔｉ－６Ａｌ－４Ｖ合金和ＴＣ１１合金银脆开裂的作用。     

压阻式压力传感器及其应用电路设计

介绍了压阻式传感器的工作原理以及相关应用电路，并给出了一个应用示例加以说明。     

K0.9Li0.1（Ta0.5Nb0.5）O3晶体压电应变系数的测量

用准静态ｄ＿（３３）测量仪和干涉法相结合。测量了Ｋ＿（０．９）Ｌｉ＿（０．１）（Ｔａ＿（０．５）Ｎｂ＿（０．５）Ｎｂ＿（０．５））Ｏ＿３晶体的压电应变系数。结果为：ｄ＿（３３）＝８６．０，ｄ＿（３３）＝一２９．５，ｄ＿（１５）＝１１２．９×１０￣（－１２）Ｃ／Ｎ．     

关于离散Kirchhoff薄板单元的研究

本文对离散Kirchhoff薄板单元进行了深入的分析。文中将用于建立离散Kirchhoff单元的泛函分为三部分,分别用应变第一不变量、绕Z轴的转动偶和有关的单元边界上的积分来表达,并阐明了各部分的作用。其中单元的收敛性质完全由第一、三部分所决定,而第二部分则控制了单元的计算精度。在此基础上,文中建议了一种提高离散Kirchhoff单元精度的新方法,并由此推导了一个任意四边形离散Kirchhoff单元。计算表明,本文的改进单元与原来的离散Kirchhoff单元及其改进型相比,计算精度有了显著提高。     

硝酸铵的膨化机理研究

膨化硝酸铵是一种自敏化改性硝酸铵,由硝酸铵溶液在专用表面活性剂作用下,经真空强制析晶工艺制得.文中研究了膨化硝酸铵制备的膨化过程和专用表面活性剂的作用,结果表明:在真空和表面活性剂作用下,硝酸铵溶液由不饱和状态至饱和状态,进而达到过饱和状态,最终导致硝酸铵的快速结晶和体系的膨胀.在真空干燥过程中,形成中心空穴、微细孔道和裂缝,它们使膨化硝酸铵的起爆感度提高;专用表面活性剂具有降低硝酸铵溶液表面张力、发泡剂和加快结晶成核的作用.     

Analytical solution for the axisymmetric plane strain electroelastic dynamics of a special non-homogeneous piezoelectric hollow cylinder

By virtue of the introduction of a dependent variable and the separation of variables technique, the axisymmetric plane strain electroelastic dynamic problem of a special non-homogeneous piezoelectric hollow cylinder is transformed to a Volterra integral equation of the second kind about a function with respect to time, which can be solved successfully by means of the interpolation method. Then the solutions of displacements, stresses, electric displacements and electric potential are obtained. The present method is suitable for a piezoelectric hollow cylinder with an arbitrary thickness subjected to arbitrary mechanical and electrical loads. Numerical results are finally presented.     

Neutron Stress Measurement of W‐Fiber Reinforced Cu Composite

Stress measurement methods using neutron and X‐ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten‐fiber reinforced copper‐matrix composite. Surface stresses were measured by X‐ray stress measurement with the sin²ψ method. Furthermore, the sin²ψ method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement.