基于去调频技术的斜视聚束SAR成像方法

针对具有方位谱混叠现象的斜视聚束式合成孔径雷达(SAR)成像问题,本文研究了一种基于去调频技术的成像方法.文中首先分析了斜视聚束SAR中的方位谱混叠现象,从理论上找出了斜视角影响方位粗聚焦的根本原因.基于分析结果,引入了回波信号非线性相位校正预处理法,彻底消除了斜视角的影响,从而得到正确的粗聚焦结果.然后基于斜视成像模型,推导了预处理回波信号的方位粗聚焦和精聚焦处理过程.在精聚焦的方位滤波处理中,针对非线性相位校正预处理导致的场景聚焦深度限制问题,提出了一种改进的非线性调频变标(NLCS)算法,实现了回波信号的高精度方位压缩.仿真实验结果证明了文中理论分析的正确性和所提方法的有效性.     

Compressive sensing SAR range compression with chirp scaling principle

Compressive sensing(CS) techniques offer a framework for the detection and allocation of sparse signal with a reduced number of measurements.This paper proposes a novel SAR range compression,namely compressive sensing with chirp scaling(CS-CS),achieving the same range resolution as conventional SAR approach,while using fewer range samplings.In order to realize accurate range cell migration correction(RCMC),chirp scaling principle is used to construct reference matrix for compressive sensing recovery.Additionally,error diagrams are designed for measurement of the performance of CS-CS,and some experiments of using real data are performed to deal with the errors caused by three conditions:SNR,sparsity and sampling.     

天车称重系统解析

以河北钢铁集团唐山钢铁有限责任公司一钢轧厂240t天车称重系统为例,介绍天车称重系统的硬件结构、工作原理、传输方式、仪表功能、称重传感器原理、钢丝绳补偿、信号传输、称重仪表等,结合在生产中的实际运行状况,总结出在生产维护中的常见问题,并提出具体的解决方法。     

平行双关节坐标测量机的精度设计

平行双关节坐标测量机是一种新型非正交坐标测量设备,具有结构简单,精度高,便携等优点。文章首先介绍了平行双关节坐标测量机的测量原理,然后分析了影响仪器测量精度的误差源及误差源的可能修正精度,计算了仪器测量总误差。根据仪器设计精度进行了误差分配,并对误差分配进行了仿真计算,总结了仪器误差分布规律。本文的研究为指导测量机的结构设计和标定提供了依据,为实现平行双关节坐标测量机的测量精度指标提供了扎实的理论基础。     

FY-3气象卫星MERSI数据快速预处理的IDL实现

作为新型卫星数据源,FY\|3/MERSI(风云三号中分辨率光谱成像仪)影像的快速预处理方法与模块目前较少见。采用基于三角网的几何校正算法,根据研究区Shapefile文件和FY\|3/MERSI自带定位数据提取处理区域,实现对应区域全部20个通道几何校正,并利用后向映射重采样输出各通道图像纠正后像元点DN值,随后进行辐射定标、太阳高度角订正等预处理。该系列过程用IDL编写相关程序实现了用户界面化交互操作。运行结果表明:设计的算法流程占用内存小,计算速度快。对于一个面积约45万km²的区域,所有通道处理耗时仅450 s,且校正后影像质量和精度均较好。相较于相同区域借助ENVI软件下地理位置查找表法(GLT)仅实现单通道几何校正耗时超30 min,本文开发的模块大大提高了FY\|3/MERSI数据处理效率,为其在城市热环境、积雪等领域的应用做好准备工作。     

A novel deep learning scheme for multi-condition remaining useful life prediction of rolling element bearings

The remaining useful life (RUL) prediction of a rolling element bearing is important for more reasonable maintenance of machinery and equipment. Generally, the information of a failure can hardly be acquired in advance while running and the degradation process varies in terms of different faults. Thus, fault identification is indispensable for a multi-condition RUL prediction, where, however, the fault identification and RUL prediction are separated in most studies. A new hybrid scheme is proposed in this paper for the multi-condition RUL prediction of rolling element bearings. The proposed scheme contains both classification and regression, where the 2D-DCNN based classifier and predictors are built concerning typical fault conditions of a bearing. For the online prediction, the raw signals are spanned in the time-frequency domain and then transferred into images as the input of the scheme. The classifier is used to monitor the vibration of rolling bearings for online fault recognition and excite the corresponding predictor for RUL prediction once a fault is detected. The output from the predictor is amended by the proposed adaptive delay correction method as the final prediction results. A demonstration is performed based on the XJTU-SY datasets and the results are compared with those from the state-of-the-art methods, which proves the superiority of the proposed scheme in improving the accuracy and linearity of RUL prediction. The time cost of the proposed online prediction scheme is also investigated and the results indicate high time effectiveness.     

Response correction techniques for surrogate‐based design optimization of microwave structures

Simulation‐based optimization has become an important design tool in microwave engineering. However, using electromagnetic (EM) solvers in the design process is a challenging task, primarily due to a high‐computational cost of an accurate EM simulation. In this article, we present a review of EM‐based design optimization techniques exploiting response‐corrected physically based low‐fidelity models. The surrogate models created through such a correction can be used to yield a reasonable approximation of the optimal design of the computationally expensive structure under consideration (high‐fidelity model). Several approaches using this idea are reviewed including output space mapping, manifold mapping, adaptive response correction, and shape‐preserving response prediction. A common feature of these methods is that they are easy to implement and computationally efficient. Application examples are provided. © 2011 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2012.     

一种制做三维牙——颌骨光弹性模型的新方法

本文提出一种用“整体浇注法”制做三维牙——颌骨光弹性模型的新方法,即用价格便宜的石膏做阴模,先制出与真实牙几何相似的牙光弹性模型和模拟牙周膜的乳胶套,将它们粘接好,然后将其放入颌骨石膏阴模的适当位置,浇入环氧树脂混合液,用“二次固化法”进行固化,即可制成三维牙——颌骨整体光弹性模型。此法能保证模型与实物的严格几何相似和牙周的边界条件相似,使实验精度大大提高且工艺简单、成本低。     

一种虚拟式的自动控制原理实验平台设计

目前多用MATLAB进行自动控制原理的各类仿真,而它所需编写代码繁琐且界面不够灵活。鉴于此,提供了利用基于G语言的LABVIEW设计的自动控制原理虚拟实验平台。从模块组成上介绍了虚拟平台所完成的设计及分析功能,并以频域响应分析、频率法校正为例详细阐述了平台设计、分析系统的原理,最后经过与MATLAB仿真结果的对比验证,表明该平台系统分析的准确性与可靠性。     

Edge diffraction correction for 3D scattering center modeling based on the shooting and bouncing ray technique

In the traditional scattering center extraction method based on the shooting and bouncing ray(SBR) technique,only the physical optics contribution of the target is considered.However,the physical optics method is unable to describe the contribution of the actual edge diffraction.By comprehensively considering the specular reflection and edge diffraction contribution of the target,an edge diffraction correction method for 3D scattering center modeling based on the SBR technique is proposed.Using the SBR technique and combining the image domain ray tube integration and equivalent edge currents method,the edge diffraction correcting formula for the 3D inverse synthetic aperture radar image is derived.Simulation results show that the proposed method is able to effectively improve the modeling accuracy of the 3D scattering center.