场效应管设计

本文概述了场效应管的分类和设计。设计按常规程序考虑，特殊的ＭＯＳ管还要考虑相关许多其它因素，以及理论与实践结合后的取舍。     

Partial scan design and test sequence generation based on reduced scan shift method

This paper presents a partial scan algorithm, calledPARES (PartialscanAlgorithm based onREduced Scan shift), for designing partial scan circuits. PARES is based on the reduced scan shift that has been previously proposed for generating short test sequences for full scan circuits. In the reduced scan shift method, one determines proch FFs must be controlled and observed for each test vector. According to the results of similar analysis, PARES selects these FFs that must be controlled or observed for a large number of test vectors, as scanned FFs. Short test sequences are generated by reducing scan shift operations using a static test compaction method. To minimize the loss of fault coverage, the order of test vectors is so determined that the unscanned FFs are in the state required by the next test vector. If there are any faults undetected yet by a test sequence derived from the test vectors, then PARES uses a sequential circuit test generator to detect the faults. Experimental results for ISCAS'89 benchmark circuits are given to demonstrate the effectiveness of PARES.     

氧化铝丝的研制

氧化铅丝生产过程中最关键的工艺是连续阳极氧化。氧化膜击穿电压决定于氧化膜厚度。控制膜厚度的三要素为:电解液(成份、浓度及温度),槽电压和铝丝走速。     

浅谈电力系统的压电控制

对当前电力系统电压控制的设备及运行进行了比较全面的总结，指出了各种控制设备的优缺点及适用范围，并结合灵活交流输电技术(FACTS技术）的发展而出现的新型FACTS设备，提出了设备的分类。     

Synthesizing Energy-Efficient Embedded Systems with LOPOCOS

In this paper, we introduce the LOPOCOS (Low Power Co-synthesis) system, a prototype CAD tool for system level co-design. LOPOCOS targets the design of energy-efficient embedded systems implemented as heterogeneous distributed architectures. In particular, it is designed to solve the specific problems involved in architectures that include dynamic voltage scalable (DVS) processors. The aim of this paper is to demonstrate how LOPOCOS can support the system designer in identifying energy-efficient hardware/software implementations for the desired embedded systems. Hence, highlighting the necessary optimization steps during design space exploration for DVS enable architectures. The optimization steps carried out in LOPOCOS involve component allocation and task/communication mapping as well as scheduling and dynamic voltage scaling. LOPOCOS has the following key features, which contribute to this energy efficiency. During the voltage scaling valuable power profile information of task execution is taken into account, hence, the accuracy of the energy estimation is improved. A combined optimization for scheduling and communication mapping based on genetic algorithm, optimizes simultaneously execution order and communication mapping towards the utilization of the DVS processors and timing behaviour. Furthermore, a separation of task and communication mapping allows a more effective implementation of both task and communication mapping optimizationsteps. Extensive experiments are conducted to demonstrate the efficiency of LOPOCOS. We report up to 38% higher energy reductions compared to previous co-synthesis techniques for DVS systems. The investigations include a real-life example of an optical flow detection algorithm.     

发展高电压等级真空断路器的技术问题探讨

本文对发展高电压等级真空断路器的关键技术问题，如触头材料，灭弧室耐压特性、电弧特性、弧后特性、波纹管设计及触头运动特性等进行了探讨，可为高电压等级真空断路器的设计提供依据。     

定电流对LED的重要性

高功率超高亮度LED已经开始大量应用.要实际体现LED(尤其是高功率超高亮度LED)的优点,采用定电流驱动方式必要条件之一.     

纵向零序电压保护新方案及其应用

由于结构设计的原因，综合性能较好的一些保护方案如横差保护和不完全纵差保护等将不能应用于大型超临界汽轮发电机。文中重点讨论了纵向零序电压保护方案的改进及其在应用中的问题。研究表明，发电机发生匝间短路故障时3次谐波电势减小，而机组外部故障时发电机3次谐波电势增大。因此，为了提高纵向零序电压保护方案的性能，可以根据故障时3次谐波电压增量的特性作为选取制动量的依据，从而提高保护性能。亦即:当3次谐波电压表现为负增量时，制动量取为0或接近0;而当3次谐波电压表现为正增量时，以该增量值作为制动量。此外，对匝间保护纵向零序电压元件增加一个小延时是可行的，它可以提高保护躲暂态3次谐波影响的能力。仿真计算表明，比例制动式纵向零序电压保护能可靠区分内外部故障，符合大型超临界汽轮发电机的保护要求。     

带有长测量电缆的电容分压器的传输特性

该文研究了z_3=z_0,z_4=∞情况下电容分压器测量系统的传输特性,得出了U_(in)(s)=G(s)~(-1)U_0(s)在时间域的解析解及其差分形式,此解正可用于进行波形重建。给出了波形畸变与分压器、电缆及被测波形参数间的定量关系。     

特高压输电线路负序方向纵联保护

采用数字式二阶RC低通滤波器和半波差分傅里叶算法，结合相序变换滤取负序分量，可在微机保护中实现负序方向元件，并可在故障初几毫秒内正确动作。用该方法实现的负序方向元件可正确及时地捕捉到由不对称故障发展起来的三相短路故障瞬间的不对称，故可以反映各种不对称故障和由不对称故障发展起来的三相故障。仿真试验验证了用所提出的方法实现的负序方向元件用于特高压输电线路的可行性和优越性。